AG Neovo E-W22 Manuel utilisateur
Table of Contents
Precautions............................................................................................................... 2
Notice .................................................................................................................... 2
Installation ............................................................................................................. 2
Warning on power connection ............................................................................... 2
Maintenance .......................................................................................................... 2
Transportation ....................................................................................................... 3
Adjusting Your LCD display Viewing Angle ........................................................... 3
Wall mounting........................................................................................................ 4
Getting Started.......................................................................................................... 5
Unpacking Your LCD Display ................................................................................5
Product Features ................................................................................................... 6
Control Buttons...................................................................................................... 7
Setup ..................................................................................................................... 8
Software Configuration .......................................................................................... 9
Adjusting Your LCD Display....................................................................................10
Selecting OSD Features...................................................................................... 10
OSD Menus ......................................................................................................... 11
Warning Messages and Troubleshooting................................................................ 15
Warning Messages.............................................................................................. 15
Troubleshooting Guide ........................................................................................ 16
Specification ........................................................................................................ 17
Regulations............................................................................................................. 18
FCC Declaimers ..................................................................................................18
TCO’06 ................................................................................................................ 19
IT Equipment Recycling Information.................................................................... 20
WEEE.................................................................................................................. 20
Hg........................................................................................................................ 20
1
Precautions
Notice
• The product specifications and other information provided in this User Manual are for
reference only. Provided information was correct at time of print. All information is subject
to change without notice. Updated content can be downloaded from our website at
http://www.agneovo.com.
• To register online, please go to http://www.agneovo.com.
• To protect your rights as a consumer, do not remove any stickers from this product. Doing
so may affect the determination of the product’s warranty period.
Installation
• Do not cover or block the ventilation holes in the housing.
• Do not place the monitor near a heat source, such as a space heater or exhaust vent, nor
in direct sunlight.
• Do not place this device in any location subject to vibration or other physical shocks.
Warning on power connection
• Use an appropriate power cord to connect the monitor to a power outlet.
• The outlet should be installed near the monitor and be easily accessible.
• Do not allow anything to rest on the power cord.
• Disconnect the power plug from the power outlet in the following circumstances:
If you will not use the monitor for an indefinite period time.
When the power cord or plug is damaged of frayed.
If the product has been dropped or the housing has been damaged.
If the product exhibits a distinct change in performance, indicating a need for service.
Maintenance
• Clean the housing, glass panel and controls with a soft cloth lightly moistened with a mild
detergent solution. Do not use any type of abrasive pad, scouring powder or solvent, such
as alcohol or benzene.
• Do not rub, touch, or tap the surface of the screen with sharp or abrasive items such as a
pen or screwdriver. This type of contact may result in scratching the surface of the glass.
• Do not insert sharp objects or spill liquid into the monitor through ventilation holes. This
may cause accidental fire, electric shock or failure of the device.
• Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltages or other risks.
2
Transportation
When you transport this monitor for repair or shipment, use the original carton and packing
materials.
Retracting the base stand
If you want to bend up the base to 90 degrees for transportation, please push the 2
metal pillars on the bottom of base and fold to 90 degrees as shown in the illustration
below.
The maximum tilt angle of the monitor is 25°; the monitor can not be pushed down any further
when the tilt angle is at the 25° position.
Adjusting Your LCD display Viewing Angle
You can adjust your LCD display between 5°~25° by holding the top of the panel with both hands
and pushing back and forth to adjust the viewing angle to the desired angle.
3
Wall mounting
If you want to mount your LCD display on the wall, please follow the steps described below using
the wall mount kit or arm..
First, remove rear cover
Insert a coin or flat screwdriver into the rear cover slot and pull out the rear cover.
Second, unlock base assembly
1. Unlock two screws
2. Remove base assembly
Third, mount arm or wall mount kit on the rear side.
AG Neovo wall-mountable products (wall mount kit, WMK series) are recommended.
4
Getting Started
Unpacking Your LCD Display
After you have unpacked your LCD display, make sure that the following items are included in
the package.
• LCD display
• Adaptor (Output Voltage should be 12Vdc and Ampere should be min.4A)
• Power cord
• D-sub 15-pin VGA cable (*1)
• DVI-D digital cable (*1)
• Audio cable
• CD-ROM (*1) • Quick Guide (*1)
5
Product Features
1. Control buttons
2. Earphone jack
3. Built-in speakers
4. Foldable base
5. NeoV Optical GlassTM
6
Control Buttons
Front View
ON/OFF Button
Push once to turn your LCD display ON and push again to turn it OFF.
Power LED
The power LED will turn to green under normal operation and orange when in
standby mode.
Move RIGHT
Call out OSD menu.
Select OSD menu features from left to right, and bottom to top.
Move LEFT
Call out OSD menu.
Select OSD menu features from right to left, and bottom to top.
Increase
Call out the volume bar; increase the volume.
Navigate within the display.
Decrease
Turn mute on or off; decrease the volume.
Navigate within the display.
AUTO button / Video Mode
Press to select preferable video mode ：User, Text, Movie, Game or
Graphic. The option will toggle on the top right hand corner of the display.
Press button for 3 seconds to adjust the picture position and performance
automatically. You are recommended to press the button the first time you use
the monitor or every time you change the resolution and/or refresh rate of the
input signal.
7
Setup
Please follow the following instructions to setup monitor.
Step 1: Remove all packing materials and wrapping from the monitor and then tear down the
plastic dust cover from the screen surface.
Step 2: With the computer or video equipment turned off, connect the signal cable.
• Connecting to an IBM or IBM compatible computer
• Connecting to a video equipment with digital source
Step 3: With the monitor turned off, connect the monitor end power plug of adapter to the
power jack of the monitor. Then connect the power cord to the adapter and the
power plug to the power source.
Step 4: Turn on your computer or video equipment. Press power switch to turn on
monitor.
8
Step 5: Set for best performance.
Set for E-W22 LCD monitor, it will have the best performance at resolution 1680 x 1050.
Ensure that your computer display is set at 1680 x 1050 pixels and 60Hz. Press the
AUTO button. The monitor will optimizes the display automatically.
For E-W19 LCD monitor, it will have the best performance at resolution 1440 x 900.
Ensure that your computer display is set at 1440 x 900 pixels and 60Hz. Press the
AUTO button. The monitor will optimize the display automatically.
Software Configuration
Installing the Microsoft Windows data file
You can find the Microsoft Windows data file (also called the driver program) on the included AG
Neovo CD. To ensure smooth operation after initial installation, you can refer to the installation
guide, which can also be found on the CD.
9
Autres manuels pour E-W22
3
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels AG Neovo Moniteur
AG Neovo
AG Neovo PS-55 Manuel du propriétaire
AG Neovo
AG Neovo RX-W22 Manuel utilisateur
AG Neovo
AG Neovo X-17P Manuel du propriétaire
AG Neovo
AG Neovo E-19 Manuel utilisateur
AG Neovo
AG Neovo SX-17P Manuel utilisateur
AG Neovo
AG Neovo L-W27 Manuel utilisateur
AG Neovo
AG Neovo SC-17 Manuel utilisateur
AG Neovo
AG Neovo X-Series Manuel utilisateur
AG Neovo
AG Neovo TX-1502 Manuel utilisateur
AG Neovo
AG Neovo X-17 Manuel utilisateur
AG Neovo
AG Neovo TM-23 Manuel utilisateur
AG Neovo
AG Neovo F-215 Manuel utilisateur
AG Neovo
AG Neovo K-A19 Manuel utilisateur
AG Neovo
AG Neovo TS-15S Manuel utilisateur
AG Neovo
AG Neovo RX-W32 Manuel utilisateur
AG Neovo
AG Neovo SX-15 Manuel utilisateur
AG Neovo
AG Neovo QM-43 Manuel utilisateur
AG Neovo
AG Neovo DR-22 Manuel utilisateur
AG Neovo
AG Neovo H-19D Manuel utilisateur
AG Neovo
AG Neovo L-W24 Manuel utilisateur
