AFL Hyperscale 96HP Manuel utilisateur

Level 4 96f Backboard

Installation Guide

96f POC

Backboard

Conguration SKU Code

96HP 10014768

Safety Precautions

Laser Precautions

Warning: The laser light used to transmit information over optical ber cables can cause severe eye

damage. Because this light is invisible, it will not cause the iris of the eye to contract involuntarily as when

viewing a bright visible light, and no pain is felt as the retina is burned.

Never look into the end of a ber or connector which may have a laser coupled to it. Should accidental

eye exposure to laser light be suspected, arrange for an eye examination immediately.

General Precautions

Personnel must be thoroughly familiarized with all applicable Occupational Health and Safety (OH&S)

regulations, local regulations, and your company safety practices and policies.

Warning: To reduce the chance of accidental injury:

Before work begins, all personnel must be thoroughly familiar with the operation of all equipment

and procedures to be used during the installation.

Before use, all equipment, especially safety gear, must be inspected and tested for proper operation.

Replace and repair as necessary.

96f PoC Backboard

Before installing or adjusting this product, please read these instructions carefully.

Please keep this guide for future reference.

Level 4 96f PoC Backboard

Component Overview

1. Backboard

2. Cassette Chassis

3. Cable Manager

4. Pedestal Cable Manager

5. 3 Finger Cable Manager

6. Splice Tray

7. 1x4 Splitter Tray

8. Modular Raceway

9. Cable/Tube Manifold

10. Single Duct Tie Point

11. Universal Duct Tie Point

12. Installation Guide / QR Code

In the Box

Item

Number Item Qty

01 Backboard 1

02 Cassette Chassis 2

03 Cable Manager 2

04 Pedestal Cable Manager 4

05 3 Finger Cable Manager 2

06 Splice Tray 6

07 1x4 Splitter Tray 6

08 Modular Raceway 4

09 Cable/Tube Manifold 1

10 Single Duct Tie Point 2

11 Universal Duct Tie Point 12

12 Installation Guide / QR Code 1

(01) Backboard

(06) 8mm Splice Tray

(03) Cable Manager

(02) Cassette

Chassis

(07) 1x4 Splitter Tray (08) Modular Raceway

(11) Universal 8-way

Duct Tie point

(12) nstallation Guide

/ QR Code

(05) 3 Finger Cable

Manager

(09) ) Cable/Tube

Manifold

(10) Single Duct Tie Point

(04) Pedestal Cable

Manager

Cable Ties Splice ProtectorsTube Cutter

Marker PenScissors Cross-Head

Screwdriver

What You Will Need Related Products

FCP2 Fiber Cleaning Kit for SC/ST/FC/LC

Level 4 96f PoC Backboard

Backboard Installation

Slot studs into back panel - no tools required.

Backboard must be central, top, location as shown.

Rear Section View

24f cable looped inside the raceway.

Use tie-off positions for network duct/cable.

Secure using hose clip.

Install 24f cable – minimum overlength 3m from

gas block (Ø3mm blowing cable only).

Cut the ducts to length and push duct into teeth

and secure with cable tie. Push on blowing

indicator (not supplied).

Installation Process

Level 4 96f PoC Backboard

Splitter input bre map

Tray / Module map – Colours for document visualization only

Cable/Tray – Fibre Map

Installation Process

Tray Type Tray Position Linked to Module

8mm Splice Tray

4 x 1x4

Splitter Tray

812

710

8mm Splice Tray

* Virgin Media

recommended

ber routing.

Please check

splicing schedule

* Virgin Media

recommended

ber routing.

Please check

splicing schedule

Overall Routing

1:4 Splitter Outputs

(routed to modules)

1:4 Splitter Outputs

(routed to splice tray)

Network ber

from L3 – all 24

into one tray

Cable Routing

Level 4 96f PoC Backboard

Routing 1:4 Splitter Outputs trays 3-5 down to network splice tray. Excess splitter input tail length should be

stored in the splitter trays, not the splice trays.

1:4 Splitter Outputs

(routed to modules)

1:4 Splitter Inputs

(routed to splice tray)

1x4 G.657A2

splitter

1:4 Routing: Trays 3-5

1:4 Routing: Trays 6-8

Routing 1:4 Splitter Outputs trays 6-8 down to network splice tray. Excess splitter input tail length should be

stored in the splitter trays, not the splice trays.

1:4 Splitter

Outputs

(routed to

modules)

1:4 Splitter Inputs

(routed to splice

tray)

1x4 G.657A2

splitter

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels AFL Hyperscale Matériel informatique

AFL Hyperscale

AFL Hyperscale 288f Manuel utilisateur

AFL Hyperscale

AFL Hyperscale H-Series 7RU Housing Manuel utilisateur