Advantech RUGGED PENTIUM IPPC-9120 Manuel utilisateur

IPPC-9120/9150 Series

Rugged Pentium®III/Celeron™

Industrial panel PC with

12.1"/15" LCD display

User’s Manual

This document is copyrighted 2001, by Advantech Co. Ltd. All rights are

reserved. Advantech Co., Ltd. reserves the right to alter the products de-

scribed in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or

transmitted in any form or by any means without the prior written

permission of Advantech. Information provided in this manual is intended to

be accurate and reliable. However, Advantech assumes no responsibility for use

of this manual, nor for any infringements upon the rights of third parties

which may result from such use.

All brand and product names mentioned herein are trademarks or

registered trademarks of their respective holders.

Part No. 2002000100

1st Edition Printed in Taiwan January 2001

Acknowledgments

ADAM is a trademark of Advantech Co., Ltd.

IBM and PC are trademarks of International Business Machines Corporation.

FCC Class B

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a residential environment. This equipment

generates, uses and can radiate radio frequency energy. If not installed and

used in accordance with this user's manual, it may cause harmful interference

to radio communications. Note that even when this equipment is installed and

used in accordance with this user’s manual, there is still no guarantee that

interference will not occur. If this equipment is believed to be causing

harmful interference to radio or television reception, this can be determined

by turning the equipment on and off. If interference is occuring, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment to a power outlet on a circuit different from that to

which the receiver is connected

• Consult a dealer or an experienced radio/TV technician for help

Warning: Any changes or modifications made to the equipment

which are not expressly approved by the relevant stan-

dards authority could void your authority to operate the

equipment.

Packing List

Before setting up the system, check that the items listed below are included

and in good condition. If any item does not accord with the table, please

contact our dealer immediately.

TheIPPC-9120/9150SeriesindustrialpanelPCsincludethefollowingmodels:

1. IPPC-9120T

RuggedPentium®III/Celeron™industrialpanelPCwith12.1”TFTLCD

2. IPPC-9120T-T

IPPC-9120T with resistive type touchscreen

3. IPPC-9150T

RuggedPentium®III/Celeron™industrialpanelPCwith15”TFTLCD

4. IPPC-9150T-T

IPPC-9150T with resistive type touchscreen

5. IPPC-9150T-N

IPPC-9150T with NFI touchscreen

Packing List

Item IPPC-9120T IPPC-9150T

Description Rugged Pentium® III/Celeron™

industrial panel PC with LCD display

LCD type 12.1" TFT SVGA 15" TFT XGA

Display

resolution 800 x 600 1024 x 768

Motherboard PCM-9571B

Floppy disk

drive 3.5" slim type

Power supply 80 W; 100 ~ 250 VAC

Items in

accessory box

One utility CD-ROM

One CPU fan with heat sink

One Y-shaped adapter for PS/2 mouse

and PS/2 keyboard

Optional Devices

Touchscreen Resistive Resistive or NFI

Slim type CD-

ROM drive

24X slim type CD-ROM

One floppy disk with CD-ROM drive

Additional Information and Assistance

1. Visit the Advantech websites at www.advantech.com or

www.advantech.com.tw, where you can find the latest information about

the product.

2. Contact your distributor, sales representative, or Advantech's customer

service center for technical support if you need additional assistance.

Please have the following information ready before you call:

• Product name and serial number

• Description of your peripheral attachments

• Description of your software (operating system, version, application

software, etc.)

• A complete description of the problem

• The exact wording of any error messages

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User's Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not

use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the

equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall

may cause damage.

7. The openings on the enclosure are for air convection. Protect the equipment from

overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the equipment to

the power outlet.

9. Position the power cord so that people cannot step on it. Do not place anything over the

power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source to avoid

damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be opened only by

qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work according to the

user's manual.

e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED

ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW

-20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY DAMAGE THE EQUIPMENT.

The sound pressure level at the operator's position according to IEC 704-1:1982 is no

more than 70dB(A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech

disclaims all responsibility for the accuracy of any statements contained herein.

Wichtige Sicherheishinweise

1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine

Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung.

4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen

könnte Verletzungen hervorrufen.

7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor überhitzung

schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden.

8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.

9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann. Es sollte

auch nichts auf der Leitung abgestellt werden.

10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten.

11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz

trennen. Somit wird im Falle einer Überspannung eine

Beschädigung vermieden.

12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das

Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen.

13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur

von authorisiertem Servicepersonal geöffnet werden.

14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von

einer qualifizierten Servicestelle zu überprüfen:

a - Netzkabel oder Netzstecker sind beschädigt.

b - Flüssigkeit ist in das Gerät eingedrungen.

c - Das Gerät war Feuchtigkeit ausgesetzt.

d - Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioni ert oder

Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.

e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.

f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

15. Bitte lassen Sie das Gerät nicht unbehehrt hinten unter -20° C (-4° F) oder oben 60° C

(140° F), weil diesen Temperaturen das Gerät zerstören könten.

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70dB(A)

oder weiger.

DISCLAIMER: This set of instructions is given according to IEC704-1. Advantech

disclaims all responsibility for the accuracy of any statements contained herein.

Contents

Chapter 1 General Information 1

1.1 Introduction............................................................................2

1.2 Specifications .......................................................................3

General .................................................................................... 3

Standard PC functions ............................................................... 3

PCI SVGA/flat panel interface..................................................... 4

Audio function ........................................................................... 4

PCI bus Ethernet interface.......................................................... 5

Analog Resistive Touchscreen (optional) ...................................... 5

NFI Touchscreen (optional) ......................................................... 5

Optional modules ...................................................................... 5

1.3 Dimensions ...........................................................................7

Chapter 2 System Setup 9

2.1 A Quick Tour of the IPPC-9120/9150 Series ..................10

2.1.1 PS/2 mouse and keyboard ................................................12

2.1.2 Parallel port .....................................................................12

2.1.3 Serial COM ports .............................................................13

2.1.4 VGA port .........................................................................13

2.1.5 USB ports .......................................................................14

2.1.6 Audio interface.................................................................14

2.1.7 Ethernet ..........................................................................14

2.1.8 Adjusting the LCD brightness ............................................14

2.2 Installing SDRAM ...............................................................15

2.3 Installing a CPU..................................................................16

2.4 Installing a 2.5" HDD..........................................................18

2.5 Installing a CD-ROM Drive ................................................21

2.6 Installing Add-on Cards .....................................................23

2.7 Mounting Instructions..........................................................24

2.7.1 Panel mounting ................................................................24

2.7.2 Rack mounting.................................................................26

Chapter 3 Jumper Settings and Connectors 29

3.1 Jumpers and Connectors ..................................................30

3.1.1 Setting jumpers ................................................................30

3.1.2 Jumpers and switch..........................................................31

3.1.3 Locating jumpers and switch .............................................32

3.1.4 Connectors ......................................................................33

3.1.5 Locating connectors .........................................................34

3.2 CPU Installation..................................................................35

3.3 COM-port Interface.............................................................35

3.3.1 COM2 RS-232/422/485 setting (JP3, JP4, JP5)...................35

3.3.2 COM1 / COM2 pin 9 output type setting (JP9) ....................36

3.3.3 COM3 / COM4 pin 9 output type setting (JP6) ....................37

3.4 CMOS Clear for External RTC (JP8) ...............................37

3.5 Internal -12 V Source Enable Setting (JP1) ....................38

3.6 VGA Interface .....................................................................38

3.6.1 LCD panel power setting ...................................................38

3.6.2 Panel type select (SW3) ...................................................38

3.7 Watchdog Timer Configuration.........................................39

3.7.1 Watchdog activity selection (JP7) ......................................39

Chapter 4 PCI Bus Ethernet Interface 41

4.1 Introduction..........................................................................42

4.2 Installation of Ethernet Driver ............................................42

4.2.1 Installation for Windows 95................................................43

4.2.2 Installation for Windows 98................................................46

4.2.3 Installation for Windows NT ...............................................49

4.3 Further Information .............................................................52

Chapter 5 PCI SVGA Setup 53

5.1 Introduction..........................................................................54

5.1.1 Chipset ...........................................................................54

5.1.2 Display memory ...............................................................54

5.1.3 Display types ...................................................................54

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Advantech Écran tactile

Advantech

Advantech PPC-S154T Manuel utilisateur

Advantech

Advantech PPC-6151C Manuel d'installation et d'exploitation

Advantech

Advantech PPC-310W EHL Manuel utilisateur

Advantech

Advantech PPC-150T-RT Manuel utilisateur

Advantech

Advantech PPC-L62T Manuel utilisateur

Advantech

Advantech PPC-100 Manuel utilisateur

Advantech

Advantech PPC-157T Manuel utilisateur

Advantech

Advantech PPC-L128T Manuel utilisateur

Advantech

Advantech PPC-3150SW Manuel utilisateur

Advantech

Advantech PPC-3150SW Manuel d'installation et d'exploitation

Advantech

Advantech TPC-1560 Manuel utilisateur

Advantech

Advantech PPC-3151W Manuel d'installation et d'exploitation

Advantech

Advantech IPPC-5211WS Series Manuel utilisateur

Advantech

Advantech PPC-321W TGL Manuel utilisateur

Advantech

Advantech PPC-3150 Manuel utilisateur

Advantech

Advantech ITA-8100 Manuel utilisateur

Advantech

Advantech PPC-415W Manuel d'installation et d'exploitation

Advantech

Advantech PPC-A84 Manuel utilisateur

Advantech

Advantech TPC-1261H Manuel utilisateur

Advantech

Advantech UltraSlim PPC-S153 Manuel utilisateur

Advantech

Advantech PPC-L158T Manuel utilisateur

Advantech

Advantech POC-174 Manuel utilisateur

Advantech

Advantech SPC-57 Manuel utilisateur

Advantech

Advantech PPC-S123 Manuel utilisateur

Manuels Écran tactile populaires d'autres marques

FlowLine

FlowLine Data loop Manuel utilisateur

ALPEX

ALPEX AEx-8 P Series Manuel utilisateur

Ltech

Ltech E5S Manuel utilisateur

Harman

Harman AMX MODERO S MSD-701-L2 Manuel utilisateur

Acnodes

Acnodes PC 1150 Manuel utilisateur

AIS

AIS IP10IA99 series Manuel utilisateur

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manuel utilisateur

YASKAWA

YASKAWA TP 610C Manuel utilisateur

B&R

B&R Power Panel C Series Manuel utilisateur

Beijer Electronics

Beijer Electronics X2 control Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT321W-521 Manuel utilisateur

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manuel utilisateur

Qomo

Qomo QIT1386 Manuel utilisateur

DFI

DFI KS104-CD Manuel utilisateur

AMX

AMX AXP-PPC Mode d’emploi

Sartorius

Sartorius X3 PR 5410 Manuel utilisateur

AMX

AMX Modero X Series Manuel utilisateur

B&R Industries

B&R Industries MAPPC900-ENG Manuel utilisateur