Advantech PPC-S154T Manuel utilisateur

PPC-S154T

UltraSlim™ Mobile Intel®

Pentium® 4 processor-M based

15" panel PC

User’s Manual

PPC-S154T User’s Manual ii

nal manufacturer reserves the right to make improvements to the products

described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or transmit-

ted in any form or by any means without the prior written permission of

the original manufacturer. Information provided in this manual is

intended to be accurate and reliable. However, the original manufacturer

assumes no responsibility for its use, nor for any infringements upon the

rights of third parties that may result from such use.

Acknowledgements

Award is a trademark of Award Software International, Inc.

VIA is a trademark of VIA Technologies, Inc.

IBM, PC/AT, PS/2 and VGA are trademarks of International Business

Machines Corporation.

Intel and Pentium are trademarks of Intel Corporation.

Microsoft Windows® is a registered trademark of Microsoft Corp.

RTL is a trademark of Realtek Semi-Conductor Co., Ltd.

ESS is a trademark of ESS Technology, Inc.

UMC is a trademark of United Microelectronics Corporation.

SMI is a trademark of Silicon Motion, Inc.

Creative is a trademark of Creative Technology LTD.

All other product names or trademarks are properties of their respective

owners.

For more information on this and other Advantech products, please visit

our websites at: http://www.advantech.com

http://www.advantech.com.tw

For technical support and service, please visit our support website at:

http://service.advantech.com.tw/eservice

This manual is for the PPC-154T.

Part No. 2008S15400 1st. Edition

Printed in Taiwan September 2003

iii

FCC Class B

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interfer-

ence when the equipment is operated in a residential environment. This

equipment generates, uses and can radiate radio frequency energy. If not

installed and used in accordance with this user's manual, it may cause

harmful interference to radio communications. Note that even when this

equipment is installed and used in accordance with this user's manual,

there is still no guarantee that interference will not occur. If this equip-

ment is believed to be causing harmful interference to radio or television

reception, this can be determined by turning the equipment on and off. If

interference is occurring, the user is encouraged to try to correct the inter-

ference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment to a power outlet on a circuit different from that

to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Warning! Any changes or modifications made to the

equipment which are not expressly approved by

the relevant standards authority could void your

authority to operate the equipment.

PPC-S154T User’s Manual iv

Packing List

Before you begin installing your card, please make sure that the following

materials have been shipped:

• PPC-154T series panel PC

• User's manual (note 1)

• Accessories for PPC-154T

- Y-shaped adapter for PS/2 mouse and keyboard

- Warranty card

- Power cord: USA type

- AC/DC power adapter

- Floppy disk with CD-ROM drive driver

-"Drivers and Utilities" CD-ROM disc

-VESA-standard bracket for mounting

- Mounting kits and packet of screws

- Heat sink (note 1)

- Heat sink support plate kits (note 2)

-Thermal pad (note 3)

-Thernal grease (note 4)

If any of these items are missing or damaged, contact your distributor or

sales representative immediately.

Note 1: If the unit is without a CPU, this is included in

the accessory box. If the unit comes with a

CPU, the heat sink is installed in the unit

Note 2: If the support plate kits are on the motherboard,

then the heat sink can be installed on the plate

Note 3: The thermal pad needs to put around the CPU

die as a buffer between heat sink and CPU

Note 4: Put the thermal grease on the CPU die for

transferring the heat to heat sink

Additional Information and Assistance

Step 1. Visit the Advantech web site at www.advantech.com or

www.advantech.com.tw where you can find the latest informa-

tion about the product.

Step 2. Contact your distributor, sales representative, or Advantech's cus-

tomer service center for technical support if you need additional

assistance. Please have the following information ready before

you call:

• Product name and serial number

• Description of your peripheral attachments

• Description of your software (operating system, version, application

software, etc.)

• A complete description of the problem

• The exact wording of any error messages

Warning! 1. Input voltage rated 16V ~ 25Vdc, 3.5 A max

2. Use a 3 V @ 195 mA lithium battery

3. Packing: please carry the unit with both

hands, handle with care

4. Maintenance: to properly maintain and clean

the surfaces, use only approved products or

clean with a dry applicator

5. CompactFlash: Turn off power before insert-

ing or removing CompactFlash storage card.

Contact information:

Our European representative:

Advantech Europe GmbH

Kolberger Straße 7

D-40599 Düsseldorf, Germany

Tel: 49-211-97477350

Fax: 49-211-97477300

PPC-S154T User’s Manual vi

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User's Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp

cloth. Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the

equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or let-

ting it fall may cause damage.

7. The openings on the enclosure are for air convection. Protect the equipment

from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

9. Position the power cord so that people cannot step on it. Do not place anything

over the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power

source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be

opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service

personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work according

to the user's manual.

e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE

THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR

ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE

EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.

16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY

REPLACED.REPLACE ONLY WITH THE SAME OR EQUIVALENT

TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED

BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUC-

TIONS.

The sound pressure level at the operator's position according to IEC 704-1:1982 is

no more than 70 dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advan-

tech disclaims all responsibility for the accuracy of any statements contained

herein.

vii

W i c h t i g e S i c h e r h e i s h i n w e i s e

1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie

Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch

zur Reinigung.

4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht

zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen

oder Fallen könnte Verletzungen hervorrufen.

7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor überhit-

zung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden.

8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.

9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann.

Es sollte auch nichts auf der Leitung abgestellt werden.

10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu

beachten.

11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom

Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädi-

gung vermieden.

12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten

in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag aus-

lösen.

13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen

Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.

14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen

und von einer qualifizierten Servicestelle zu überprüfen:

a - Netzkabel oder Netzstecker sind beschädigt.

b - Flüssigkeit ist in das Gerät eingedrungen.

c - Das Gerät war Feuchtigkeit ausgesetzt.

d - Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert

oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.

e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.

f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

15. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Batte-

rie.Ersatz nur durch densellben order einem vom Hersteller empfohlene-

mahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des

Herstellers.

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000

beträgt 70dB(A) oder weiger.

PPC-S154T User’s Manual viii

DISCLAIMER: This set of instructions is given according to IEC704-1.

Advantech disclaims all responsibility for the accuracy of any statements

contained herein.

1 Table of Contents

CONTENTS

Chapter 1 General Information ........................................2

1.1 Introduction ....................................................................... 2

1.2 General Specifications....................................................... 3

1.3 LCD Specifications ........................................................... 6

1.4 Dimensions........................................................................ 6

Figure 1.1:Dimensions of PPC-154T.............................. 6

Chapter 2 System Setup.....................................................8

2.1 A Quick Tour of the Panel PC .......................................... 8

Figure 2.1:Front view of the panel PC............................ 8

Figure 2.2:Left side view of the panel PC ...................... 9

Figure 2.3:Rear view of the panel PC........................... 10

Figure 2.4:Rear and bottom view of the panel PC........ 10

2.2 Installation Procedures .................................................... 11

2.2.1 Connecting the power cord ........................................... 11

2.2.2 Connecting the keyboard or mouse .............................. 11

2.2.3 Switching on the power ................................................ 11

Figure 2.5:Connecting the power cord to the DC inlet. 11

Figure 2.6:Power switch in lock status ......................... 12

Figure 2.7:Power switch in open status ........................ 12

2.3 Running the BIOS Setup Program .................................. 13

2.4 Installing System Software.............................................. 14

2.5 Installing the Drivers....................................................... 15

Chapter 3 Hardware and Peripheral Installation .........18

3.1 Overview of Hardware Installation and Upgrading ........ 18

3.2 Installing the 2.5" Hard Disk Drive (HDD) .................... 18

Figure 3.1:Install the HDD on the HDD bracke ........... 19

Figure 3.2:Connect HDD to the HDD cable................. 19

3.3 Installing the SDRAM Memory Module and

Central Processing Unit (CPU) ....................................... 20

Figure 3.3:Detaching the CPU plastic cover and

heat sink .................................................... 20

Figure 3.4:CPU with thermal pad ................................. 21

Chapter 4 Jumper Settings and Connectors..................24

4.1 Setting jumpers................................................................ 24

4.1.1 Jumpers and switch....................................................... 25

Table 4.1:Jumpers and their functions.......................... 25

4.1.2 Locating jumpers and switch ........................................ 25

Figure 4.1:Locating jumpers on the PPC-S154T mother-

board25

PPC-S154TUser’sManual 2

4.1.3 Installing the 2.5" Hard Disk Drive (HDD).................. 26

Table 4.2:Panel PC connectors ..................................... 26

4.1.4 Locating connectors...................................................... 27

Figure 4.2:Locating connectors on the PPC-S154T

motherboard .............................................. 27

4.2 CPU Installation .............................................................. 27

4.3 CMOS Clear for External RTC (JP3) ............................. 28

Table 4.3:Clear CMOS / External RTC (JP3) .............. 28

4.4 COM-port Interface......................................................... 28

4.4.1 COM2 RS-232/422/485 setting (JP4)........................... 28

Table 4.4:COM2 RS-232/422/485 setting (JP4)........... 28

Table 4.5:COM2 RS-232/422/485 setting (JP4)........... 29

Table 4.6:COM2 RS-232/422/485 setting (J4)............. 29

Table 4.7:Serial port default settings ............................ 29

4.4.2 COM1/COM2/COM3/ pin 9 output setting (JP5) ........ 30

Table 4.8:COM1/2/3 pin 9 output setting(JP5) ............ 30

4.5 VGA Interface................................................................. 30

4.5.1 LCD panel power setting .............................................. 31

4.5.2 Panel type select (SW1)................................................ 31

Table 4.9:Panel type select (SW1)................................ 31

4.6 Watchdog Timer Configuration ...................................... 31

Chapter 5 Intel Chipset....................................................34

5.1 Introduction ..................................................................... 34

5.1.1 Installation INF driver for Windows 98/2000/XP ........ 34

5.1.2 Installation IAA driver for Windows 98/2000/XP ....... 34

5.2 Further Information......................................................... 35

Chapter 6 AGP SVGA Setup ..........................................38

6.1 Introduction ..................................................................... 38

6.1.1 Chipset .......................................................................... 38

6.1.2 Display memory............................................................ 38

6.2 Installation of SVGA Driver ..................... 38

6.2.1 Installation for Windows 98 ......................................... 39

6.2.2 Installation for Windows 2000/XP ............................... 39

6.3 Further Information......................................................... 40

Chapter 7 PCI Bus Ethernet Interface...........................42

7.1 Introduction ..................................................................... 42

7.2 Installation of Ethernet Driver......................................... 42

7.2.1 Installation for Windows 98/NT/ME/2000................... 43

7.2.2 Installation for Windows 2000/ME/XP ........................ 43

7.3 Further Information......................................................... 44

Chapter 8 Audio ...............................................................46

8.1 Introduction ..................................................................... 46

Table des matières

Autres manuels Advantech Écran tactile

Advantech

Advantech IPPC-7158 Series Manuel utilisateur

Advantech

Advantech PPC-L157T Manuel utilisateur

Advantech

Advantech UTC-318H Manuel utilisateur

Advantech

Advantech POC-W152 Manuel d'instructions

Advantech

Advantech PPC-315W TGL Manuel d'installation et d'exploitation

Advantech

Advantech PPC-3100S Manuel utilisateur

Advantech

Advantech PPC-150 Series Manuel utilisateur

Advantech

Advantech PPC-112W Manuel d'installation et d'exploitation

Advantech

Advantech IPPC-6172A Series Manuel utilisateur

Advantech

Advantech PPC-123 Manuel utilisateur

Advantech

Advantech PPC-306 EHL Manuel d'installation et d'exploitation

Advantech

Advantech PPC-3120-RE9A Instructions d'installation

Advantech

Advantech TPC-1881WP Series Manuel utilisateur

Advantech

Advantech PPC-3100-RE9A Manuel utilisateur

Advantech

Advantech PPC-306 EHL Manuel utilisateur

Advantech

Advantech TPC-650H Manuel utilisateur

Advantech

Advantech SPC-57 Manuel utilisateur

Advantech

Advantech TPC-51WP Series Manuel utilisateur

Advantech

Advantech IPPC-5211WS Series Manuel utilisateur

Advantech

Advantech HMI-640S Manuel utilisateur

Advantech

Advantech PPC-L127T Manuel utilisateur

Advantech

Advantech PPC-6151C Manuel d'installation et d'exploitation

Advantech

Advantech TPC-1581WP Manuel utilisateur

Advantech

Advantech PPC-177T Manuel utilisateur

Manuels Écran tactile populaires d'autres marques

FlowLine

FlowLine Data loop Manuel utilisateur

ALPEX

ALPEX AEx-8 P Series Manuel utilisateur

Ltech

Ltech E5S Manuel utilisateur

Harman

Harman AMX MODERO S MSD-701-L2 Manuel utilisateur

Acnodes

Acnodes PC 1150 Manuel utilisateur

AIS

AIS IP10IA99 series Manuel utilisateur

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manuel utilisateur

YASKAWA

YASKAWA TP 610C Manuel utilisateur

B&R

B&R Power Panel C Series Manuel utilisateur

Beijer Electronics

Beijer Electronics X2 control Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT321W-521 Manuel utilisateur

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manuel utilisateur

Qomo

Qomo QIT1386 Manuel utilisateur

DFI

DFI KS104-CD Manuel utilisateur

AMX

AMX AXP-PPC Mode d’emploi

Sartorius

Sartorius X3 PR 5410 Manuel utilisateur

AMX

AMX Modero X Series Manuel utilisateur

B&R Industries

B&R Industries MAPPC900-ENG Manuel utilisateur