Advantech AIMB-788 Manuel utilisateur

The information contained in this document has been carefully researched and is, to the best of our

knowledge, accurate. However, we assume no liability for any product failures or damages, immediate or

consequential, resulting from the use of the information provided herein. Our products are not intended for

use in systems in which failures of product could result in personal injury. All trademarks mentioned herein

are property of their respective owners. All specifications are subject to change without notice.

Manual

ADVANTECH

AIMB-788

Industrial ATX Motherboard for Intel® 12th generation Core™ i9/i7/i5/i3 & Pentium®/Celeron®

processor with Q670E chipset

AIMB-788 Startup Manual 1

AIMB-788 LGA1700 12th Generation Intel®Core™ i9/i7/

i5/i3 ATX Motherboard with DP/HDMI/VGA, DDR4, USB

3.2, M.2

Startup Manual

Specications (Cont.) Packing List

For more information on this and other Advantech prod-

ucts, please visit our website at:

http://www.advantech.com

For technical support and service, please visit our sup-

port website for AIMB-788 at:

http://advt.ch/aimb788spt

extra warranty for Free at:

http://www.register.advantech.com

This manual is for the AIMB-788 series Rev. A1, and all

specications are subject to the data-sheet on the o󰀩cial

website. The information in this manual is subject to

change without notice..

Part No. 2041078800

Printed in China

1st Edition

May 2022

• M.2 socket: One M.2 socket supports up to PCIe x4 Gen

3 M-key 2280 type storage devices.

• SATA interface: Four on-board Serial ATA 3.0 connectors

support data transmission rates up to 600 MB/s. All four

SATA 3.0 ports support Advanced Host Controller Inter-

face (AHCI) technology.

• PCIe and PCI slot: 1 PCIe x16 Gen 4 expansion slot, 1

PCIe x8 expansion slot (x4 Gen 3 link), 3 PCIe x4 Gen

3 expansion slots, 2 PCI slots 32-bit/33 MHz PCI 2.2

compliant.

• USB 3.2/2.0: 2 USB 3.2 Gen 2 ports on rear with up to

10 Gb/s data rate, 4 USB 3.2 Gen 1 ports (2 rear, 2 via

header), 8 USB 2.0 ports (4 rear, 2 via header, 2 internal

Type-A).

• Serial port: Six serial ports: COM1, COM2 and COM4 ~

6 are RS-232; COM3 is RS-232/422/485 with jumper and

BIOS menu options.

• SPI interface: Advantech-designed SPI connector sup-

ports optional TPM 2.0 module.

• Watchdog timer: 255 sec timer level intervals.

Graphic Interface

• Chipset: CPU integrated graphics controller.

• Display memory: 1 GB maximum shared memory with 2

GB and above system memory installed.

• DisplayPort: Resolution up to 4096 x 2304 @ 60 Hz

refresh rate.

• HDMI: Resolution up to 3840 x 2160 @ 30 Hz refresh

rate.

• VGA: Resolution up to 1920 x 1200 @ 60 Hz refresh rate.

Ethernet Interface

• Interface: 10/100/1000 Mbps.

• Controller: LAN1: Intel

I219-LM; LAN2: Intel

I210-AT.

Mechanical and Environmental

• Dimensions (L x W): 304.8 x 244 mm (12” x 9.6”)

• Power consumption:

Intel Core i 65W; DDR4 32 GB x 4

Maximum: +3.3 V at 1.41 A, +5 V at 2.42 A, +12 V at 9.3 A,

+5 Vsb at 0.13 A, -12 V at 0.04 A, -5 V at 0.05 A

• Operating temperature: 0 ~ 60° C (depending on CPU load-

ing and thermal solution)

• Weight of board: 0.7 kg (1.54 lb)

Before you begin installing your card, please make sure that

the following items have been shipped:

• 1 x AIMB-788 motherboard

• 1 x AIMB-788 startup manual

• 2 x Serial ATA HDD data cables

• 1 x I/O port bracket

If any of these items are missing or damaged, please con-

tact your distributor or sales representative immediately.

Standard Functions

• CPU: LGA1700 socket supporting 12th generation Intel®

Core™ i9/i7/i5/i3/Pentium/Celeron processor.

• BIOS: AMI 256 Mbit SPI BIOS.

• Chipset: Intel® Q670E PCH.

Note: Legacy platforms are not supported.

• System memory: Up to 128 GB in four 288-pin DIMM

sockets supporting dual-channel DDR4 3200 SDRAM.

AIMB-788 supports non-ECC unbu󰀨ered DIMMs and

does not support any memory conguration that mixes

non-ECC with ECC unbu󰀨ered DIMMs.

Specications

2 AIMB-788 Startup Manual

The board has a number of jumpers that allow you to con-

gure your system to suit your application. The table below

lists the function of each jumper and connector.

Connector / Jumper List

Label Function

LAN1 ~ LAN2 GbE LAN

USB3C1 USB 3.2 Gen 2 port *2

USB3C2 USB 3.2 Gen 1 port *2

USB3H1 USB 3.2 Gen 1 port *2

(20-pin header)

USB2C1 USB 2.0 port *4

USB2A1 ~

USB2A2 USB 2.0 port (internal Type-A)

USB2H2 USB 2.0 port *2 (10-pin header)

COM1+VGA1 Serial port: RS-232 (DB-9 connec-

tor) / VGA connector

DP1+HDMI1 DP connector / HDMI connector

COM2,

COM4 ~ COM6 Serial port: RS-232 (9-pin header)

COM3 Serial port: RS-232/422/485 (9-pin

header)

CPUFAN1 CPU fan connector (4-pin)

SYSFAN1 ~

SYSFAN3 System fan connector (4-pin)

JFP3

Power LED

Suspend: fast ash (ATX/AT)

System on: on (ATX/AT)

System o󰀨: o󰀨 (ATX/AT)

JFP2 External speaker / HDD LED con-

nector / SMBus connector

JFP1 Power switch / reset connector

AUDIO1+AUDIO2 Audio connector (Line Out, Mic In)

VOLT1 Alarm board power connector

JCASE1 Case open connector

LANLED1 Front panel LAN indicator con-

nector

NVME1 M.2 2280 M-key socket

SATA4 ~ SATA7 Serial ATA 3.0 port

PCI1 ~ PCI2 PCI slot

PCIE1 PCIe x16 slot (x16 Gen 4 link)

PCIE2 , PCIE4,

PCIE5 PCIe x4 slot (x4 Gen 3 link)

PCIE3 PCIe x8 slot (x4 Gen 3 link)

DIMMA1 Channel A DIMM1

DIMMA2 Channel A DIMM2

DIMMB1 Channel B DIMM1

DIMMB2 Channel B DIMM2

ATX12V1+

ATX12V2

ATX 12 V auxiliary power connec-

tor (for CPU)

EATXPWR1 ATX 24-pin main power connector

(for system)

SPDIF_OUT1 SPDIF audio out pin header

GPIO1 8 bit GPIO from super I/O

SMBUS1 SMBus connector from PCH

FPAUD1 Front panel audio connector

SPI_TPM1 SPI(Serial Peripheral Interface)

connector

Note!

Due to Intel design specication, the PCIE1 slot can only

support graphic cards and storage cards (1x8 bifurcated

PCIe 5.0, 1x4 PCIe 4.0). Other types of add-on cards will

have no function installed on this slot.

JCMOS1: CMOS clear data

JME1: Intel ME update

Closed Pins Result

1-2 *Keep CMOS data

*Enable ME update

2-3

Clear CMOS data

Disable ME update

* Default

*Keep CMOS data Clear CMOS data

*Enable ME update Disable ME update

JWDT1+JOBS1: Watchdog timer output and OBS alarm

Closed Pins

Result

2-4, 8-10 Watchdog timer disable (2-4)

OBS beep (8-10)

4-6, 8-10 *Watchdog timer reset (4-6)

OBS beep (8-10)

* Default

Watchdog timer disable (2-4) *Watchdog timer reset (4-6)

OBS beep (8-10) OBS beep (8-10)

1 2 3

Jumpers and Connectors Jumpers and Connectors (Cont.)

AIMB-788 Startup Manual 3

PSON1: ATX/AT mode selection

Closed Pins

Result

1-2 AT mode

2-3 *ATX mode

* Default

AT mode *ATX mode

JUSB_2 (onboard USB): USB power source switch

between +5V and +5V_DUAL

Closed Pins

Result

1-2 *USB +5V_DUAL power

2-3 USB +5V power

* Default

*USB +5 V_DUAL power USB +5 V power

JPCICLK1: PCI clock selection

Closed Pins

Result

1-2 66 MHz

2-3 *33 MHz

* Default

66 MHz 33 MHz

SMB1 (clock), SMB2 (data): PCIe SMBus connec-

tion setting for PCIE2~PCIE5 slots

SMB3 (clock), SMB4 (data): PCIe SMBus connec-

tion setting for PCIE1 slot

Closed Pins

Result

1-2 *Enable PCIe SMBus connection

2-3 Disable PCIe SMBus connection

* Default

*Enable PCIe SMBus connection Disable PCIe SMBus connection

Note! SMB1+SMB2 or SMB3+SMB4 jumpers should be

switched to the same setting, either 1-2 closed or

2-3 closed.

1 2 3

JSETCOM3: COM3 RS-232/422/485 jumper setting

Closed Pins

Result

5-6, 7-9, 8-10, 13-15, 14-16 *RS-232

3-4, 9-11, 10-12, 15-17, 16-18 RS-422

1-2, 9-11, 10-12, 15-17, 16-18 RS-485

* Default

Note!

BIOS setting change is necessary if RS-422 or RS-485

is selected. Please refer to Chapter 3 of user manual for

further setting.

JT1(TX signal), JR1(RX signal): COM3 RS-422/485

termination resistor

Closed Pins

Result

1-2 Disable termination

2-3 *Enable termination

* Default

Disable termination *Enable termination

JFV1: VGA dummy load setting

Closed Pins

Result

1-2 Enable VGA dummy load

2-3 *Disable VGA dummy load

* Default

Enable VGA dummy load *Disable VGA dummy load

Note! It is recommended to leave this function disabled

if you use DVI/DP as your main display.

*RS-232

RS-422

RS-485

Jumpers and Connectors (Cont.) Jumpers and Connectors (Cont.)

4 AIMB-788 Startup Manual

Caution! The computer is supplied with a battery-powered

realtime clock circuit. There is a danger of explo-

sion if battery is incorrectly replaced. Replace

only with same or equivalent type recommended

by the manufacturer. Discard used batteries ac-

cording to manufacturer’s instructions.

This device complies with the requirements in Part 15 of

the FCC rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,

including interference that may cause undesired opera-

tion.

Declaration of Conformity

Figure 1: Board Layout: Jumper and Connector Locations

COM1

VGA1

DP1

HDMI1

AUDIO1+AUDIO2

LAN2

USB3C2

LAN1

USB3C1

USB2C1 SPDIF_OUT1 FPAUD1

LANLED1

SYSFAN3

JFV1

CPUFAN1

ATX12V1+ATX12V2

DIMMB2

DIMMB1

DIMMA2

DIMMA1

VOLT1 EATXPWR1 PSON1 JWDT1+JOBS1

JFP3

JFP1+JFP2

SPI_TPM1

SATA4 SATA6

SATA5 SATA7

SYSFAN2

SYSFAN1

GPIO1

NVME1

Intel LGA1700

Core i9/i7/i5/i3 CPU

Intel Q670E PCH

PCI1

PCIE2, PCIE3, PCIE4, PCIE5

PCI2

JPCICLK1

SMB4

SMB3

SMB2

SMB1

PCIE1

COM6

COM5

COM4

COM3

USB2A1

USB3H1

USB2H2

USB2A2

JUSB_2

JCMOS1

JME1

JCASE1

JESPI1+JESPI2

JSETCOM3

JT1+JR1

COM2

SMBUS1

3 6 9 12

25811

PWRSW RESET

HDDLED

SNMP

JFP1

2 5 8 11

1 4 7 10

HDDLED

SM_BUS

SPEAKER

JFP2

PWRLED & N/C

12345

JFP3

Board Layout

Our company network supports you worldwide with offices in Germany, Austria, Switzerland, the UK and the

USA. For more information please contact:

Headquarters

Germany

FORTEC Elektronik AG

Augsburger Str. 2b

82110 Germering

Phone: +49 89 894450-0

E-Mail: [email protected]

Internet: www.fortecag.de

Fortec Group Members

Austria

Distec GmbH Office Vienna

Nuschinggasse 12

1230 Wien

Phone: +43 1 8673492-0

E-Mail: [email protected]

Internet: www.distec.de

Germany

Distec GmbH

Augsburger Str. 2b

82110 Germering

Phone: +49 89 894363-0

E-Mail: [email protected]

Internet: www.distec.de

Switzerland

ALTRAC AG

Bahnhofstraße 3

5436 Würenlos

Phone: +41 44 7446111

E-Mail: [email protected]

Internet: www.altrac.ch

United Kingdom

Display Technology Ltd.

Osprey House, 1 Osprey Court

Hinchingbrooke Business Park

Huntingdon, Cambridgeshire, PE29 6FN

Phone: +44 1480 411600

E-Mail: info@displaytechnology.co.uk

Internet: www. displaytechnology.co.uk

USA

Apollo Display Technologies, Corp.

87 Raynor Avenue, Unit 1

Ronkonkoma, NY 11779

Phone: +1 631 5804360

E-Mail: info@apollodisplays.com

Internet: www.apollodisplays.com

Autres manuels pour AIMB-788

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Advantech Carte mère

Advantech

Advantech AIMB-767 Manuel utilisateur

Advantech

Advantech AIMB-562 series Manuel utilisateur

Advantech

Advantech AIMB-503 Manuel utilisateur

Advantech

Advantech ASMB-310IR Manuel d'installation et d'exploitation

Advantech

Advantech AIMB-560 Series Manuel utilisateur

Advantech

Advantech AIMB-240 Series Manuel d'installation et d'exploitation

Advantech

Advantech AIMB-562 KIOSK Manuel utilisateur

Advantech

Advantech PCI-6886F-M0A1 Manuel utilisateur

Advantech

Advantech PPC-MB-610 Manuel d'installation et d'exploitation

Advantech

Advantech AIMB-275 Manuel utilisateur

Advantech

Advantech SOM-4475 Manuel utilisateur

Advantech

Advantech AIMB-215 B1 Manuel utilisateur

Advantech

Advantech PCM-9376 Manuel utilisateur

Advantech

Advantech AIMB-308 Manuel d'installation et d'exploitation

Advantech

Advantech AIMB-760 Manuel utilisateur

Advantech

Advantech PCI-6771 series Manuel utilisateur

Advantech

Advantech AIMB-785 Manuel utilisateur

Advantech

Advantech PCA-6188 Manuel d'installation et d'exploitation

Advantech

Advantech PCM-9388 Manuel d'installation et d'exploitation

Advantech

Advantech AIMB-232 Manuel d'installation et d'exploitation

Advantech

Advantech AIMB-760 Manuel d'installation et d'exploitation

Advantech

Advantech PCM-9377 Manuel utilisateur

Advantech

Advantech SOM-6882 Manuel utilisateur

Advantech

Advantech PCE-5126 Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur