Advantech ADAM-6251 Manuel d'installation et d'exploitation

STARTUP MANUAL

1 Startup Manual

ADAM-6251

16-ch Digital Input Modbus TCP Module

Notes

For more information on this and other Advantech

products, please visit our websites at:

http://www.advantech.com

http://www.advantech.com/eAutomation

For technical support and service:

http://www.advantech.com.tw/eservice

This startup manual is for the ADAM-6251

Part No: 2003625100 1st Edition

February 2013

Switch Settings

It mainly presents the switch conguration for Dry Contact

and Wet Contact wiring in Digital Input interface.

Switch SW1 SW2

Position 12341234

DI Channel Ch3 Ch2 Ch1 Ch0 Ch7 Ch6 Ch5 Ch4

Switch SW3 SW4

Position 12341234

DI Channel Ch11 Ch10 Ch9 Ch8 Ch15 Ch14 Ch13 Ch12

ON Dry Contact (Default)

OFF Wet Contact

Overview

Thank you for purchasing this ADAM-6200 series

module.This is a quick guide to help you deploy the

ADAM-6200 series module in your application eld. It

will include power and application wiring. If you need a

more complicated or specic installation, you could try

to contact ADVANTECH for advanced technical support

or suggestions.

Input Power Requirements

The ADAM-6200 system is designed for a standard

industrial unregulated 24 VDC power supply. For further

applications, it can also accept +10 to +30 VDC of power

input, 200mV peak to peak of power ripple, and the

immediate ripple voltage should be maintained between

+10 and +30 VDC.

Application Wiring

Isolated Digital Input

Dry Contact

Wet Contact

STARTUP MANUAL

Startup Manual 2

Daisy Chain Limitations

Here are the limitations of daisy chain connection with

auto-bypass protection enabled.

Read the following statement carefully before

installation.

In general, the maximum cabling distance of each

100BASE-TX network segment is 100 meter. Based

on this limitation, the maximum total connection length

in daisy chain wiring should also be 100m as if auto-

bypass protection active. See the following gure as

example, the distance from rst to second module is

50m, so as second to third. When the power fails on

second (middle) module, the auto-bypass will activate to

bridge the network connection. The total distance from

rst to the 3rd will become 100m, that means the total

network segment is close to limitation.

Furthermore, for the reason of signal transmission

characteristics, the continuous auto-bypass node should

be less than 2, so that the network communication in

daisy chain wiring is workable.

The purpose of the auto-bypass protection is to help user

minimize the damage situation of module power outage.

Note that when a power outage occurs on ADAM-

6200 modules, there exists around 2.5 seconds buffer

time for internally switching to auto-pass circuit.That

means Ethernet packets can’t reach the other devices

by daisy-chaining after this power-down module in

around 2.5 seconds.The valid connection duration after

the auto-bypass function is enabled is at most around

4 days, otherwise, the Ethernet communication will be

interrupted until power is restored.

STARTUP MANUAL

Autres manuels Advantech Système d'E/S

Advantech

Advantech PCI-1750SO Manuel utilisateur

Advantech

Advantech ADAM-6100PN Series Manuel utilisateur

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Advantech

Advantech PCIE-1756H Manuel utilisateur

Advantech

Advantech PCIE-1762H Manuel utilisateur

Advantech

Advantech MIC-75G20 Manuel d'installation et d'exploitation

Advantech

Advantech ADAM-5000/TCP Series Manuel utilisateur

Advantech

Advantech PCL-720 Manuel utilisateur

Advantech

Advantech ADAM-5013 Manuel utilisateur

Advantech

Advantech UNO-2000-LKAE Manuel utilisateur

Advantech

Advantech PCI-1758UDIO Manuel d'installation et d'exploitation

Advantech

Advantech PCIE-1762H Manuel utilisateur

Advantech

Advantech USB-5817 Manuel d'installation et d'exploitation

Advantech

Advantech WISE-4050 Manuel utilisateur

Advantech

Advantech PCI-1730 Manuel utilisateur

Advantech

Advantech WISE-4000 Series Manuel utilisateur

Advantech

Advantech AMAX-5000 Series Manuel utilisateur

Advantech

Advantech PCM-3730 Manuel utilisateur

Advantech

Advantech ADAM-6000 series Manuel utilisateur

Advantech

Advantech PCIE-1730 Series Manuel utilisateur

Advantech

Advantech AIIS-E730 Manuel d'installation et d'exploitation

Advantech

Advantech USB-5820 Manuel utilisateur

Advantech

Advantech PCL-733 Manuel utilisateur

Advantech

Advantech USB-4716 Manuel utilisateur

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur

WAGO

WAGO I/O-SYSTEM 750 Manuel utilisateur