ADTRAN TRACER 4x06 Manuel de référence

Converting the Frequency Plan of a TRACER 4x06(L2) System

Introduction

TRACER 4x06 systems are shipped from the factory with the frequency plan programmed as Plan A or

Plan B. Each wireless link must contain a Plan A radio on one end and a Plan B on the other. A frequency

plan conversion may be performed in the field, but should only be attempted if absolutely necessary and

must always be performed by qualified personnel. This document outlines the procedure for changing the

frequency plan of a List 2 (L2) TRACER 4x06 system (TRACER 4106 - P/N 12804106L2A/B or

TRACER 4206 - P/N 12804206L2A/B).

Prerequisite Procedures

The current frequency plan configuration is listed on a label located on the rear panel of the unit (near the

Antenna connector). Record the current configuration before beginning this procedure.

Tools and Materials Required

• 5/16” Torque wrench (8 in-lbs)

• 3/16” nut driver

• Phillips-head screw driver

Disconnect all cables attached to the TRACER 4x06 system (including power, data,

terminal RS-232, etc.) before performing this procedure.

Do not attempt to perform the conversion without the proper tools (see list below). Using

improper tools will damage the unit.

Electronic equipment can be damaged by static electrical discharge. Before handling

equipment, put on an antistatic discharge wrist strap to prevent damage to components.

Place equipment in antistatic packing material when transporting or storing. When

working on equipment, always place it on an approved antistatic mat that is electrically

grounded.

TRACER 4x06(L2) Frequency Conversion Document

1. Remove the screws from the chassis cover using a Phillips-head screwdriver (see Figure 1).

Figure 1. Removing the Cover Screws (TRACER 4x06)

2. Remove the nuts on either side of the RS-232 connector (on the rear panel of the unit) using the 3/16”

nut driver (see Figure 2).

Figure 2. Removing the RS-232 Nuts

3. Carefully slide the cover toward the back of the unit until the front edge of the cover is disconnected

from the front of the unit. Lift the cover off and set aside.

Perform the steps below in the order listed.

Remove all connected mounting brackets before attempting to remove the unit cover.

TRACER 4x06(L2) Frequency Conversion Document

4. Verify the current frequency plan configuration. To verify the plan, check the connections between the

J connectors (located on the board and labeled J1 and J2) and the Chan connectors (located on the

diplexer). The Chan connectors are labeled 2421 (Chan 1) and 2462 (Chan 2) for most TRACER 4106

systems and CH1 and CH2 for most TRACER 4206 systems. The following table outlines the

connections for Plan A and B.

Click to see a digital image of the J connectors or the Chan connectors.

5. Using the torque wrench, disconnect both cables from the Chan connectors on the diplexer. Do not

attempt to disconnect the J connectors (located on the board) as this will cause damage. Click here for

a digital picture of this step.

6. Carefully flex the cables to swap the connections. Be careful with the RF cables, making sure that the

minimum bend radius of the cable is greater than 0.75"; bends and loops smaller than a quarter will

cause the RF cable to break. Use the wiring guidelines in Figure 3 and Figure 4 on page 4 for help with

wire placement. Click here for a digital picture of this step.

Figure 3. TRACER 4106 Cable Routing Diagrams

TRACER 4x06

PLAN CHAN 1 CHAN 2

AJ2 J1

BJ1 J2

Allowing the RF cables to sit on the processor and radio boards (green) could cause

damage to the boards; keep the RF cables off the boards while re-routing them. Click here

for a digital picture of this mistake.

ANT

PLAN B

J1 CABLE OVER ANT CABLE

2421

2462

ANT

PLAN A

J2 CABLE UNDER J1 CABLE

2421

2462

TRACER 4x06(L2) Frequency Conversion Document

Figure 4. TRACER 4206 Cable Routing Diagrams

7. Use the torque wrench to reconnect the RF cables to the Chan connectors. Tighten the cables by

turning clockwise until you hear a click from the wrench. DO NOT overtighten connectors as this will

cause the RF cable to break. The TRACER 4x06 system will not operate properly with broken RF

cables.

8. Reinstall the cover and carefully tighten all screws.

9. Change label on back of the unit to reflect the Plan change.

J1 J2

CH2 CH1

PLAN B

J1 J2

CH2 CH1

PLAN A

>> BACK

Autres manuels ADTRAN Matériel réseau

ADTRAN

ADTRAN Total Access 3000 Manuel

ADTRAN

ADTRAN DDS T200 Mode d’emploi

ADTRAN

ADTRAN JOBAID Total Access 838 Manuel utilisateur

ADTRAN

ADTRAN Express 6500 Series Mode d’emploi

ADTRAN

ADTRAN 1200864L1 Manuel utilisateur

ADTRAN

ADTRAN 1442823F1 Manuel utilisateur

ADTRAN

ADTRAN HDSL4 Mode d’emploi

ADTRAN

ADTRAN Total Access 850 Guide de l'utilisateur

ADTRAN

ADTRAN NetVanta 1700801G1 Manuel utilisateur

ADTRAN

ADTRAN 1442702PG1 Manuel utilisateur

ADTRAN

ADTRAN ESU LT Manuel utilisateur

ADTRAN

ADTRAN NetVanta 8044M Manuel utilisateur

ADTRAN

ADTRAN 500 Series Manuel utilisateur

ADTRAN

ADTRAN NetVanta Series Manuel utilisateur

ADTRAN

ADTRAN 424 ONT Manuel utilisateur

ADTRAN

ADTRAN NETVANTA UNIFIED COMMUNICATIONS DEMO KIT Manuel utilisateur

ADTRAN

ADTRAN NetVanta 1531 Series Manuel

ADTRAN

ADTRAN Express 6530 6530 Manuel

ADTRAN

ADTRAN ENHANCED PSD 239 H2R Manuel utilisateur

ADTRAN

ADTRAN Total Access 900E Series Manuel utilisateur

ADTRAN

ADTRAN NetVanta 2000 Series Manuel utilisateur

ADTRAN

ADTRAN TOTAL ACCESS 600R Manuel utilisateur

ADTRAN

ADTRAN NIU3 Mode d’emploi

ADTRAN

ADTRAN 24-Port DSLAM Access Module IADSL Module Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur