ADTRAN DSU IQ Manuel utilisateur

DSU IQ

Data Service Unit

with Frame Relay

Performance Monitoring

User Manual

61200212L1-1D

December 2000

DSU IQ Unit 1200212L1

Ethernet Card 1204005L1

4-wire SW56 DBU Card 1204001L1

V.34 DBU Card 1204002L1

ISDN DBU Card 1204004L1

External DCE Card 1204006L1

PRI DBU Card 1204008L1

V.34 DBU Card 1204002L2

Trademark Information

Open View is a registered trademark of Hewlett-Packard Company.

SunNet Manager is a registered trademark of Sun Microsystems, Inc.

Netview is a registered trademark of IBM.

IQ View is a trademark of ADTRAN, Inc.

This product includes software developed by the University of California, Berkeley,

and its contributors.

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

(256) 963-8000

Printed in U.S.A.

iii

The following conventions are used in this manual.

Notes provide additional useful information.

Cautions signify information that could prevent service interruption.

Warnings provide informationthatcould preventdamage tothe equip-

ment or endangerment to human life.

FCC regulations require that the following information be provided in this manual:

1. This equipment complies with Part 68 of the FCC rules. On the bottom of the equipment

housing is a label that shows the FCC registration number and Ringer Equivalence Num-

ber (REN) for this equipment, if applicable. If required, this information must be given to

the telephone company.

2. The following information may be required when applying to the local telephone company

for leased line facilities.

3. An FCC compliant telephone cord with a modular plug may be provided with this equip-

ment. This equipment is designed to be connected to the telephone network or premises

wiring using a compatible modular jack, which is FCC Part 68 compliant. See installation

instructions for details.

4. If this equipment causes harm to the telephone network, the telephone company may tem-

porarily discontinue service. If possible, advance notification is given; otherwise, notifica-

tion is given as soon as possible. The telephone company will advise the customer of the

right to file a complaint with the FCC.

5. The telephone company may make changes in its facilities, equipment, operations, or pro-

cedures that could affect the proper operation of this equipment. If this happens, the tele-

phone company will provide advance notification and the opportunity to make the

necessary modifications to maintain uninterrupted service.

6. If experiencing difficulty with this equipment,please contact ADTRAN for repair and war-

ranty information. If the equipment is causing harm to the network, the telephone com-

pany may request this equipment to be disconnectedfrom the network until the problem is

resolved or it is certain that the equipment is not malfunctioning.

7. This unit contains no user-serviceable parts.

8. The FCC recommends that the AC outlet to which equipment requiring AC power is to be

installed, be provided with an AC surge arrester.

Service Type REN/SOC FIC Network Jacks

56/64 Kbps Digital Interface 6.0F 04DU5-56/64 RJ48S

Affidavit for Connection of Customer Premises Equipment to 1.544

MBPS and/or Subrate Digital Services

For the work to be performed in the certified territory of ______________ (telco name)

State of ________________________________

County of ______________________________

I, _______________________ (name), ____________________ (business address),

_____________________ (telephone number) being duly sworn, state:

I have the responsibility for the operation and maintenance of the terminal equipment

to be connected to 1.544 Mbps and/or __________________ subrate digital services.

The terminal equipment to be connected complies with Part 68 of the FCC rules

except for the encoded analog content and billing protection specification.

With respect to encoded analogcontent and billing protection:

( ) I attest that all operations associated with the establishment, maintenance and

adjustment of the digital CPE with respect to encoded analog content and billing pro-

tection information continuously complies with Part 68 of the FCC rules and Regula-

tions.

( ) The digital CPE does not transmit digital signals containing encoded analog con-

tent or billing information which is intended to be decoded within the telecommuni-

cations network.

( ) The encoded analog content and billing protection is factory set and is not under

the control of the customer.

I attest that the operator(s) maintainer(s) of the digital CPEresponsible for the estab-

lishment, maintenance and adjustment of the encoded analog content and billing

information has (have) been trained toperform these functions by successfully having

completed one of the following (check appropriate blocks):

( ) A. A training course provided by the manufacturer/grantee of the equipment used

to encode analog signals; or

( ) B. A training course provided by the customer or authorized representative, using

training materials and instructions provided by the manufacturer/grantee of the

equipment used to encode analog signals; or

( ) C. An independent training course (e.g., trade school or technical institution) rec-

ognized by the manufacturer/grantee of the equipment used to encode analog sig-

nals; or

( ) D. In lieu of the proceeding training requirements, the operator(s)/maintainer(S) is

(are) under the control of a supervisor trained in accordance with _______________

(circle one) above.

I agree to provide ____________________ (telco’s name) with proper documentation

to demonstrate compliance with the information in the preceding paragraph, if so

requested.

_____________________ Signature

_____________________ Title

_____________________ Date

Subscribed and sworn to before me

This _________ day of ___________________, 20__

_______________________________________

Notary Public

My commission expires: _________________________

vii

Affidavit Requirements for Connection to Digital Services

• An affidavit is required to be given to the telephone company whenever digital

terminal equipment without encoded analog content and billing protection is

used to transmit digital signals containing encoded analog content which are

intended for eventual conversion into voice band analog signal and transmitted

on the network.

• The affidavit shall affirm that either no encoded analog content or billing informa-

tion is being transmitted or that the output of the device meets Part 68 encoded

analog content or billing protection specification.

• End use/customer will be responsible to file an affidavit with the local exchange

carrier when connecting unprotected CPE to a 1.544 Mbps or subrate digital ser-

vice.

• Until such time as subrate digital terminal equipment is registered for voice appli-

cations, the affidavit requirements for subrate services are waived.

viii

FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY

INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class A dig-

ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in

a commercial environment. This equipment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in accordance with the instruction man-

ual, may cause harmful interference to radio frequencies. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense.

Shielded cables must be used with this unit to ensure compliance with Class A FCC

limits.

CANADIAN EMISSIONS REQUIREMENTS

This digital apparatus does not exceed the Class A limits for radio noise emissions

from digital apparatus as set out in the interference-causing equipment standard enti-

tled “Digital Apparatus," ICES-003 of the Department of Communications.

Cet appareil nuerique respecte les limites de bruits radioelectriques applicables aux

appareils numeriques de Class A prescrites dans la norme sur le materiel brouilleur:

"Appareils Numeriques," NMB-003 edictee par le ministre des Communications.

Change or modifications to this unit not expressly approved by the par-

ty responsible for compliance could void the user’s authority to operate

the equipment.

CANADIAN EQUIPMENT LIMITATIONS

Notice: The Canadian Industry and Science Canada label identifies certified equip-

ment. This certification means that the equipment meets certain telecommunications

network protective, operational, and safety requirements. The Department does not

guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be con-

nected to the facilities of the local telecommunications company. The equipment must

also be installed using an acceptable methods of connection. In some cases, the com-

pany’s inside wiring associated with a single line individual service may be extended

by means of a certified connector assembly (telephone extension cord). The customer

should be aware that compliance with the above limitations may not prevent degra-

dation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian mainte-

nance facility designated by the supplier. Any repairs or alterations made by the user

to this equipment, or equipment malfunctions, may give the telecommunications

company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of

the power utility, telephone lines and internal metallic water pipe system, if present,

are connected together. This precaution may be particularly important in rural areas.

The Load Number (LN) assigned to each terminal device denotes the percentage of

the total load to be connected to a telephone loop which is used by the device, to pre-

vent overloading. The termination on a loop may consist of any combination of

devices subject only to the requirement that the total of the Load Numbers of all

devices does not exceed 100.

Users should not attempt to make such connections themselves, but should

contract the appropriate electric inspection authority, or an electrician, as

appropriate.

IMPORTANT SAFETY INFORMATION

When using your telephone equipment, please follow these basic safety precautions

to reduce the risk of fire, electrical shock, or personal injury:

1. Do not use this product near water, such as near a bath tub, wash bowl, kitchen

sink, laundry tub, in a wet basement, or near a swimming pool.

2. Avoid using a telephone (other than a cordless-type) during an electrical storm.

There is a remote risk of shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord, power supply, and/or batteries indicated in the manual.

Do not dispose of batteries in a fire. They may explode. Check with local codes

for special disposal instructions.

SAVE THESE INSTRUCTIONS

Warranty and Customer Service

ADTRAN will replace or repair this product within five years from the date of ship-

ment if it does not meet its published specifications or fails while in service. For

detailed warranty, repair, and return information refer to the ADTRAN Equipment

Warranty and Repair and Return Policy Procedure.

Return Material Authorization (RMA) is required prior to returning equipment to

ADTRAN.

For service, RMA requests, or further information, contact one of the numbers listed

at the end of this manual.

Autres manuels pour DSU IQ

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ADTRAN Matériel réseau

ADTRAN

ADTRAN NT1 ACE Manuel utilisateur

ADTRAN

ADTRAN DS3 NIU3 PM Mode d’emploi

ADTRAN

ADTRAN 12804108L1A Guide de l'utilisateur

ADTRAN

ADTRAN DDS T200 Mode d’emploi

ADTRAN

ADTRAN NetVanta 6330 Series Manuel utilisateur

ADTRAN

ADTRAN Total Access 1500 Dual FXS/DPO Manuel utilisateur

ADTRAN

ADTRAN Total Access 3000 Manuel

ADTRAN

ADTRAN ENHANCED PSD 239 H2R Manuel utilisateur

ADTRAN

ADTRAN 1442880G1 Manuel utilisateur

ADTRAN

ADTRAN ATLAS 800 Series Module QUAD E1 Manuel utilisateur

ADTRAN

ADTRAN NIU3 Mode d’emploi

ADTRAN

ADTRAN T1 Nx64 HTU-R Mode d’emploi

ADTRAN

ADTRAN TRACER 64 0 Series Manuel utilisateur

ADTRAN

ADTRAN jobAid NetVanta 838T Manuel utilisateur

ADTRAN

ADTRAN NetVanta 873 Manuel utilisateur

ADTRAN

ADTRAN Total Access 900E Series Manuel utilisateur

ADTRAN

ADTRAN NetVanta E1/FE1 Network Interface Module Manuel utilisateur

ADTRAN

ADTRAN TRACER 4305 Manuel utilisateur

ADTRAN

ADTRAN Total Reach DDS-DP 5 Series Mode d’emploi

ADTRAN

ADTRAN 1442390G1 Manuel utilisateur

ADTRAN

ADTRAN 1200312L5 Manuel utilisateur

ADTRAN

ADTRAN TR OCU DP Mode d’emploi

ADTRAN

ADTRAN DSU III ARdc Manuel utilisateur

ADTRAN

ADTRAN NetVanta 1335 Series Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur