Addonics Technologies MMTPRO Manuel utilisateur

Technical Support

If you need any assistance to get your unit functioning properly, please have your

product information ready and contact Addonics Technical Support at:

Hours: 8:30 am - 6:00 pm PST

Phone: 408-453-6212

Email: http://www.addonics.com/support/query/

T E C H N O L O G I E S

www.addonics.com

User Guide

Multi-Media Tower Pro

(MMTPRO)

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Unpacking and Overview

Bay 1

Bay 2

Bay 3

Bay 4

1. Power Button

3. Bay 1 HDD

4. Bay 2 HDD

5. Bay 3 flash media LED

6. Bay 4 HDD drive

2. Power LED

eSATA connector

AC Input

Power Switch

Power Supply

Voltage Switch

100 cm eSATA Cable Power cord (US version shown)

123456

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Connecting the Multi-Media Tower Pro

WARNING: Please remember to set the power supply to your local outlet

voltage prior to plugging in the power cord. Failure to do so may

damage the power supply.

1. Set the power supply voltage switch to the correct main input voltage, then

connect the power cord to an AC outlet.

2. Turn on the power switch on the back of the unit.

3. Connect the eSATA cable from the eSATA port on the back of the unit to an

eSATA host adapter.

4. Turn on the unit using the power button on the front.

The Multi-Media Tower Pro includes an internal 5x1 Port Multiplier. The unit

must be directly connected to an eSATA host adapter that supports port

multipliers. If the host adapter does not support port multipliers, only the first

device found in the cabinet will be seen by the controller. The unit cannot be

connected to another port multiplier.

The Multi-Media Tower Pro also supports hot swapping for all media types.

This feature must also be supported by the eSATA host adapter. If a drive or

media is inserted or removed when the unit is connected to a host adapter

that does not support hot swapping, the operating system may not reflect the

change at all or it may crash.

Identify your eSATA controller adapter and check with its hardware manufac-

turer if you are unsure if these features are supported. Addonics offers

several port multiplier compatible adapters that also support hot swapping.

Drive Installation: Bay 1 (Snap-In Mobile Rack)

1. Use the key to set the lock to the unlocked position if necessary, then

gently pull the lever.

2. Insert a 3.5” SATA drive or device installed in a Snap-In 25 adapter (not

included), SATA connector first with contacts down. The drive should give

little resistance, DO NOT FORCE IT.

3. Gently close the door over the drive until the drive is completely inserted,

then press firmly until the door snaps closed.

4. Turn the lock to the locked position. The drive will not power up until the

door is locked.

Drive Installation: Bay 2 (Internal Micro SATA UDD)

Gently insert a Micro SATA hard disk or media adapter into the bay, Micro

SATA connector with contacts first, facing down until it resists further travel.

Then press firmly to seat the Micro SATA connector. The drive will be protrud-

ing from the bay.

www.addonics.com

Phone: 408-573-8580

Fax: 408-573-8588

Email: http://www.addonics.com/sales/query/

Media Installation: Bay 3 (Internal SATA/USB DigiDrive)

The SATA Digi Drive will recognize only one media device at a time. If more

than one media device is inserted, the device found earlier on this list of slots

will be used: CompactFlash, SmartMedia/xD, SD/MMC/miniSD, MS/MS Duo.

The CompactFlash slot accepts CompactFlash media including CF Micro-

drives. Insert media connector first with label side up.

The SmartMedia/xD slot accepts SmartMedia (SmartCard) or xD Picture Card

devices. Insert SmartMedia contacts down with the “cut” corner toward the slot

on the left side. Insert xD Picture card media contacts first, facing down.

The SD/MMC/MiniSD slot will accept SD, SDHC and SdxC devices or a

miniSD installed in an adapter as well as Multi Media Card (Smart MMC)

devices. Insert media contacts first, facing down.

The MS/MS Duo slot accepts Memory Stick or Memory Stick Pro Duo devices,

insert media contacts first, facing down.

Drive Installation: Bay 4 (Multimedia Bay Hard drive)

1. Gently pull the lever until the door swings open.

2. Gently insert a SATA 3.5” hard drive or device installed in a Snap-In 25

adapter (not included), SATA connectors first, facing down. The drive should

give little resistance, DO NOT FORCE IT.

3. Gently close the door over the drive until it closes, then press firmly until it

snaps in place. The drive will power up immediately.

Table des matières

Autres manuels Addonics Technologies Matériel informatique

Addonics Technologies

Addonics Technologies MSUDDSA Manuel utilisateur

Addonics Technologies

Addonics Technologies ADSA3R5-E Manuel utilisateur

Addonics Technologies

Addonics Technologies CipherChain CCMSPC1 Manuel utilisateur

Addonics Technologies

Addonics Technologies HDUS5SNDX Manuel utilisateur

Addonics Technologies

Addonics Technologies AEMK35CB Manuel utilisateur

Addonics Technologies

Addonics Technologies CCHESEXC34 Manuel utilisateur

Addonics Technologies

Addonics Technologies RR2035ASDES Manuel utilisateur

Addonics Technologies

Addonics Technologies ADSA2 Manuel utilisateur

Addonics Technologies

Addonics Technologies HDUS1125LT Manuel utilisateur

Addonics Technologies

Addonics Technologies DGC11 Manuel utilisateur

Addonics Technologies

Addonics Technologies ADPEXC Manuel utilisateur

Addonics Technologies

Addonics Technologies ADS3GX4R5-MLM Manuel utilisateur

Addonics Technologies

Addonics Technologies AD5U2SA Manuel utilisateur

Addonics Technologies

Addonics Technologies AD5SAHPM-E Manuel utilisateur

Addonics Technologies

Addonics Technologies AD5SAPM Manuel utilisateur

Addonics Technologies

Addonics Technologies ADST114R5 Manuel utilisateur

Addonics Technologies

Addonics Technologies ADSAUSPCB Manuel utilisateur

Addonics Technologies

Addonics Technologies AD2IDEPRJ Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur