ADCMT 5350 Manuel utilisateur

MANUAL NUMBER

Printed in Japan

ADC CORPORATION

5350

Digital Electrometer

Operation Manual

FOE-00000151A00

First printing Apr 9, 2019

2019

Cover

Safety-1

Safety Summary

FOE-ANZENA01

To ensure thorough understanding of all functions and to ensure efficient use of this instrument, please read the

manual carefully before using. Note that ADC Corporation (hereafter referred to as ADC) bears absolutely no re-

sponsibility for the result of operations caused due to incorrect or inappropriate use of this instrument.

If the equipment is used in a manner not specified by ADC, the protection provided by the equipment may be im-

paired.

• Warning Labels

Warning labels are applied to ADC products in locations where specific dangers exist. Pay care-

ful attention to these labels during handling. Do not remove or tear these labels. If you have any

questions regarding warning labels, please ask your nearest ADC dealer. Our address and phone

number are listed at the end of this manual.

Symbols of those warning labels are shown below together with their meaning.

DANGER: Indicates an imminently hazardous situation which will result in death or serious

personal injury.

WARNING: Indicates a potentially hazardous situation which will result in death or serious

personal injury.

CAUTION: Indicates a potentially hazardous situation which will result in personal injury or

a damage to property including the product.

• Basic Precautions

Please observe the following precautions to prevent fire, burn, electric shock, and personal inju-

ry.

• Use a power cable rated for the voltage in question. Be sure however to use a power cable

conforming to safety standards of your nation when using a product overseas.

• When inserting the plug into the electrical outlet, first turn the power switch OFF and then

insert the plug as far as it will go.

• When removing the plug from the electrical outlet, first turn the power switch OFF and then

pull it out by gripping the plug. Do not pull on the power cable itself. Make sure your hands

are dry at this time.

• Before turning on the power, be sure to check that the supply voltage matches the voltage

requirements of the instrument.

• Connect the power cable to a power outlet that is connected to a protected ground terminal.

Grounding will be defeated if you use an extension cord which does not include a protective

conductor terminal.

• Be sure to use fuses rated for the voltage in question.

• Do not use this instrument with the case open.

• If there is any abnormality such as abnormal heart, smoke, smell or noise, immediately stop

using the instrument, turn off the power and disconnect the plug from the outlet.

Safety Summary

Safety-2

FOE-ANZENA01

• Do not place anything on the product and do not apply excessive pressure to the product. Al-

so, do not place flower pots or other containers containing liquid such as chemicals near this

product.

• When the product has ventilation outlets, do not stick or drop metal or easily flammable ob-

jects into the ventilation outlets.

• When using the product on a cart, fix it with belts to avoid its drop.

• When connecting the product to peripheral equipment, turn the power off.

• Caution Symbols Used Within this Manual

Symbols indicating items requiring caution which are used in this manual are shown below to-

gether with their meaning.

DANGER: Indicates an item where there is a danger of serious personal injury (death or seri-

ous injury).

WARNING: Indicates an item relating to personal safety or health.

CAUTION: Indicates an item relating to possible damage to the product or instrument or relat-

ing to a restriction on operation.

• Safety Marks on the Product

The following safety marks can be found on ADC products.

: ATTENTION - Refer to manual.

: Protective ground (earth) terminal.

: DANGER - High voltage.

: CAUTION - Risk of electric shock.

• Replacing Parts with Limited Life

The following parts used in the instrument are main parts with limited life.

Replace the parts listed below before their expected lifespan has expired to maintain the perfor-

mance and function of the instrument.

Note that the estimated lifespan for the parts listed below may be shortened by factors such as

the environment where the instrument is stored or used, and how often the instrument is used.

The parts inside are not user-replaceable. For a part replacement, please contact the ADC sales

office for servicing.

Each product may use parts with limited life.

For more information, refer to the section in this document where the parts with limited life are

described.

Safety Summary

Safety-3

FOE-ANZENA01

Main Parts with Limited Life

• Hard Disk Mounted Products

The operational warnings are listed below.

• Do not move, shock and vibrate the product while the power is turned on.

Reading or writing data in the hard disk unit is performed with the memory disk turning at a

high speed. It is a very delicate process.

• Store and operate the products under the following environmental conditions.

An area with no sudden temperature changes.

An area away from shock or vibrations.

An area free from moisture, dirt, or dust.

An area away from magnets or an instrument which generates a magnetic field.

• Make back-ups of important data.

The data stored in the disk may become damaged if the product is mishandled. The hard disc

has a limited life span which depends on the operational conditions. Note that there is no

guarantee for any loss of data.

• Precautions when Disposing of this Instrument

When disposing of harmful substances, be sure dispose of them properly with abiding by the

state-provided law.

Harmful substances: (1) PCB (polycarbon biphenyl)

(2) Mercury

(3) Ni-Cd (nickel cadmium)

(4) Other

Items possessing cyan, organic phosphorous and hexadic chromium

and items which may leak cadmium or arsenic (excluding lead in sol-

der).

Example: fluorescent tubes, batteries

Part name Life

Unit power supply 5 years

Fan motor 5 years

Electrolytic capacitor 5 years

LCD display 6 years

LCD backlight 2.5 years

Memory backup battery 5 years

Environmental Conditions

Safety-4

FOE-ANZENA01

This instrument should be only be used in an indoor area which satisfies the following conditions:

• An area free from corrosive gas

• An area away from direct sunlight

• A dust-free area

• An area free from vibrations

• Altitude of up to 2000 m

Figure-1 Environmental Conditions

• Operating position

Figure-2 Operating Position

• Storage position

Figure-3 Storage Position

• The classification of the transient over-voltage, which exists typically in the main power supply, and

the pollution degree is defined by IEC61010-1 and described below.

Impulse withstand voltage (over-voltage) category II defined by IEC60364-4-443

Pollution Degree 2

Vibration

Direct sunlight

Corrosive

gas

Dust

Front

The instrument must be used in a hor-

izontal position.

To prevent the internal temperature

from rising, cooling fans are installed

in some instruments.

The air vents on the case must be un-

blocked.

A clear space of 10 centimeters or more

must be kept around the air vents.

Front

This instrument should be stored in a horizontal

position.

When placed in a vertical (upright) position for

storage or transportation, ensure the instrument is

stable and secure.

-Ensure the instrument is stable.

-Pay special attention not to fall.

Safety-5

Types of Power Cable

FOE-ANZENA01

Replace any references to the power cable type, according to the following table, with the appropriate power cable

type for your country.

Plug configuration Standards Rating, color

and length

Model number

(Option number)

PSE: Japan

Electrical Appliance and

Material Safety Law

125 V at 7 A

Black

2 m (6 ft)

Straight: A01402

Angled: A01412

UL: United States of America

CSA: Canada

125 V at 7 A

Black

2 m (6 ft)

Straight: A01403

(Option 95)

Angled: A01413

CEE: Europe

DEMKO: Denmark

NEMKO: Norway

VDE: Germany

KEMA: The Netherlands

CEBEC: Belgium

OVE: Austria

FIMKO: Finland

SEMKO: Sweden

250 V at 6 A

Gray

2 m (6 ft)

Straight: A01404

(Option 96)

Angled: A01414

SEV: Switzerland 250 V at 6 A

Gray

2 m (6 ft)

Straight: A01405

(Option 97)

Angled: A01415

SAA: Australia, New Zealand 250 V at 6 A

Gray

2 m (6 ft)

Straight: A01406

(Option 98)

Angled: ---------

BS: United Kingdom 250 V at 6 A

Black

2 m (6 ft)

Straight: A01407

(Option 99)

Angled: A01417

CCC:China 250 V at 10 A

Black

2 m (6 ft)

Straight: A114009

(Option 94)

Angled: A114109

5350 Digital Electrometer Operation Manual

C-1

TABLE OF CONTENTS

1. PREFACE ...................................................................................................... 1-1

1.1 Product Overview .............................................................................................. 1-1

1.2 Supplied Accessories ........................................................................................ 1-2

1.3 Input Cables ...................................................................................................... 1-3

1.4 Optional Accessories ......................................................................................... 1-4

1.5 Operating Environment ..................................................................................... 1-5

1.6 Unpacking Inspection ........................................................................................ 1-6

1.7 Cleaning, Storage, and Transport Methods ...................................................... 1-7

1.7.1 Cleaning ...................................................................................................... 1-7

1.7.2 Storage ........................................................................................................ 1-7

1.7.3 Transport ..................................................................................................... 1-7

1.8 Life Limited Parts ............................................................................................. 1-8

1.9 Product Disposal and Recycling ....................................................................... 1-9

2. FRONT PANEL AND REAR PANEL .................................................. 2-1

2.1 Front Panel ........................................................................................................ 2-1

2.1.1 Display ........................................................................................................ 2-1

2.1.2 Control Panel .............................................................................................. 2-3

2.1.3 Input Terminal Section ............................................................................... 2-6

2.2 Rear Panel ......................................................................................................... 2-7

2.3 Displayed Messages .......................................................................................... 2-8

3. BASIC MEASUREMENTS ...................................................................... 3-1

3.1 Power Supply .................................................................................................... 3-1

3.1.1 Power Specifications .................................................................................. 3-1

3.1.2 Changing Power Voltage, and Checking and Replacing Power Fuse ........ 3-2

3.1.3 Connecting Power Cable ........................................................................... 3-4

3.1.4 Power ON and Self Test ............................................................................. 3-5

3.1.5 Setting Line Frequency ............................................................................... 3-6

3.1.6 Warm Up .................................................................................................... 3-6

3.2 DC Voltage Measurement ................................................................................ 3-7

3.2.1 Connection for DC Voltage Measurement ................................................. 3-8

3.2.2 Precautions for DC Voltage Measurement ................................................. 3-11

3.3 DC Current Measurement ................................................................................ 3-12

3.3.1 Connection for DC Current Measurement ................................................ 3-13

3.3.2 Precautions for DC Current Measurement ................................................. 3-16

4. MENU ............................................................................................................. 4-1

4.1 Menu Structure .................................................................................................. 4-1

4.2 Menu Operation Overview ................................................................................ 4-3

4.2.1 Parameters to Be Selected .......................................................................... 4-4

4.2.2 Parameters to Be Numerically Input .......................................................... 4-5

4.2.3 Parameters to Be Executed ......................................................................... 4-7

TABLE OF CONTENTS

5350 Digital Electrometer Operation Manual

Table of Contents

C-2

5. FUNCTIONAL REFERENCE ................................................................. 5-1

5.1 Sampling Operation .......................................................................................... 5-1

5.1.1 Sampling FREE RUN/HOLD .................................................................... 5-2

5.1.2 Sampling Rate ............................................................................................ 5-2

5.1.3 Trigger Delay .............................................................................................. 5-3

5.1.4 Sampling Count .......................................................................................... 5-4

5.1.5 Sampling Interval ....................................................................................... 5-4

5.2 Integration Time ................................................................................................ 5-6

5.3 Measurement Range ......................................................................................... 5-7

5.3.1 Measurement Auto Range .......................................................................... 5-8

5.3.2 Measurement Range Upper Limit/Lower Limit ......................................... 5-8

5.3.3 Measurement Auto Range Level ............................................................... 5-9

5.4 Auto Zero ......................................................................................................... 5-10

5.5 Driving Guard ................................................................................................... 5-11

5.6 Zero Check ....................................................................................................... 5-13

5.7 Measurement Data Display .............................................................................. 5-14

5.7.1 Measurement Data Display OFF ................................................................ 5-14

5.7.2 Measurement Data Display Digits .............................................................. 5-14

5.8 Math Operations ................................................................................................ 5-15

5.8.1 NULL Operation ........................................................................................ 5-15

5.8.2 Smoothing Operation .................................................................................. 5-16

5.8.3 Averaging Operation ................................................................................. 5-18

5.8.4 Totalizing Operation ................................................................................... 5-19

5.8.5 Scaling Operation ....................................................................................... 5-21

5.9 Display OFF ...................................................................................................... 5-22

5.10 Setting Parameters ............................................................................................ 5-23

5.10.1 Setting Parameters at Power ON ................................................................ 5-23

5.10.2 Setting Parameter Saving ........................................................................... 5-23

5.10.3 Setting Parameter Loading ........................................................................ 5-24

5.10.4 Setting Parameter Initialization ................................................................. 5-24

5.11 Measurement Data Memory .............................................................................. 5-28

5.11.1 Measurement Memory Store ...................................................................... 5-28

5.11.2 Measurement Data Memory Recall ............................................................ 5-29

5.12 System Functions ............................................................................................. 5-31

5.12.1 Buzzer ......................................................................................................... 5-31

5.12.2 Self Test ..................................................................................................... 5-32

5.12.3 Key Test ...................................................................................................... 5-32

5.12.4 Display Test ................................................................................................ 5-33

5.12.5 Error Log .................................................................................................... 5-33

5.12.6 Information Display .................................................................................... 5-34

5.12.7 Panel Lock .................................................................................................. 5-35

5.12.8 Password Setting ........................................................................................ 5-37

6. REMOTE CONTROL ................................................................................ 6-1

6.1 Interface Overview ............................................................................................ 6-1

6.1.1 Interface Selection ...................................................................................... 6-1

6.1.2 Compatibility with Former Model .............................................................. 6-3

6.2 GPIB .................................................................................................................. 6-5

Table des matières

Autres manuels ADCMT Instrument de mesure

ADCMT

ADCMT 8471 Manuel utilisateur

ADCMT

ADCMT 12706A Manuel utilisateur

ADCMT

ADCMT 12702A Manuel utilisateur

ADCMT

ADCMT 8230E Manuel utilisateur

ADCMT

ADCMT 8250A Manuel utilisateur

ADCMT

ADCMT 4601 I-V Meter Manuel utilisateur

ADCMT

ADCMT 8230 Manuel utilisateur

ADCMT

ADCMT 6243 Manuel utilisateur

ADCMT

ADCMT 6166 Manuel utilisateur

ADCMT

ADCMT 12704A Manuel utilisateur

ADCMT

ADCMT 8341 Manuel utilisateur

ADCMT

ADCMT 6240B Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur