ActionTec External 56K Call Waiting Manuel utilisateur

56K External

Call Waiting Modem

User Manual

Table of Contents

Proprietary Notice and Disclaimer

Unless otherwise noted, this document and the information herein disclosed are proprietary

to Actiontec Electronics, Inc. Any person or entity to whom this document is furnished or

who otherwise has possession thereof, by acceptance agrees that it will not be copied or

reproduced in whole or in part, nor used in any manner except to meet the purposes for

which it was delivered.

The information in this document is subject to change without notice and should not be

construed as a commitment by Actiontec. Although Actiontec will make every effort to in-

form users of substantive errors, Actiontec disclaims all liability for any loss or damage result-

ing from the use of this document or any hardware or software described herein, including

without limitation contingent, special or incidental liability.

PC is a trademark of IBM Corporation. MS-DOS, Windows 3.10, Windows 3.11, Windows 95 and Windows NT are trademarks of

Microsoft, Inc., K56Flex is a trademark of Lucent Technologies, Inc. and Rockwell International.

Introduction ........................................................................................... 3

Contacting Actiontec Customer Support ............................................ 3

Product Registration ............................................................................. 4

Safety Information ................................................................................. 4

Product Features ................................................................................... 5

Getting Started ...................................................................................... 5

BeforeYou Begin ................................................................................... 6

Installing the Modem.............................................................................7

Installing the Interface Cables ...........................................................7

Modem Controls and Indicators ........................................................... 8

Device Driver Installation and Configuration ...................................... 9

ConfiguringWindows 95.................................................................... 9

Configuring Windows 95B ............................................................... 12

Configuring Windows 98.................................................................. 15

Configuring Windows NT 4.0........................................................... 18

Windows 3.1X, OS/2WARP, DOS, UnixWare, and Linux ................21

Installing Communications Software................................................. 22

The CallWaiting Feature ..................................................................... 24

UsingThe CallWaiting Control Utility ................................................ 25

AT Command Set................................................................................. 26

Basic AT Commands ....................................................................... 26

AT Commands Affecting ITU-TV.90 Operation............................... 27

Examples ........................................................................................ 28

Help and Service Information ............................................................. 29

Notices ................................................................................................. 31

Introduction

Thank you for purchasing the Actiontec External 56K Call Waiting Modem. The

combination of features in this modem offer you unprecedented flexibility. By mak-

ing the Call Waiting feature a part of this state-of-the-art 56K external modem, Ac-

tiontec provides you with an easy-to-use enhancement to your on-line and off-line

communications.

The Call Waiting feature of this modem allows you to be surfing the Web and receive

notification of an incoming call. Now you will not have to miss that call. When a call

comes in while the modem is using the line, the modem will ring, just like your

phone would have normally. You can pick up the phone to quickly screen the incom-

ing call. This suspends your internet connection, rather than ending it. You can then

either stay on the phone talking or hang up to get back to surfing the Web. (Requires

that Call Waiting Service is available in your area and purchased by you from your

phone company.)

The innovative Actiontec External 56K Call Waiting Modem is also controller based.

This means full compatibility with all common PC Operating Systems such as DOS,

OS/2, UNIX, Linux, and all versions of Windows. This level of compatibility paired

with the Call Waiting feature makes the Actiontec External Call Waiting Modem a

highly versatile personal communications tool.

Contacting

Action

tec Customer Support

Actiontec Electronics prides itself on making high-quality, durable, high-performance

products. If you should need assistance, the Actiontec Technical Support Department

is available from 7:00 AM to 7:00 PM Pacific Coast Time, Monday through Friday

to provide professional support.

New drivers and firmware are released as need arises to insure maximum compatibil-

ity and operation of your new External 56K Call Waiting Modem. Find out about

these and other new Actiontec products on the web at: http://www.actiontec.com.

Actiontec Electronics, Inc.

Technical Support

760 N. Mary Avenue

Sunnyvale, CA 94086

Phone: 408-752-7714 (Choose Option 7)

Fax: 408-732-0097

BBS: 408-732-0112

Email:[email protected]

Safety Information

This modem is for use only with Personal Computers that have installation instruc-

tions detailing user installation of this type of peripheral device.

CAUTION:

To avoid shock hazard:

The power cord and any other equipment to which this product will be attached

must be connected to properly wired receptacles. Do not connect or disconnect any

cables or perform installation, maintenance, or reconfiguration of this product dur-

ing an electrical storm.

When using your telephone equipment basic safety precautions should always be

followed to reduce the risk of fire, electrical shock, and injury. Never install tele-

phone jacks in wet locations unless the jack is specifically designed for wet locations.

Never touch uninsulated telephone wires or terminals unless the telephone line has

been disconnected at the network interface. Use caution when installing or modify-

ing telephone lines. Avoid using a telephone (other than a cordless type) during an

electrical storm. There may be a remote risk of electrical shock from lightning. Do

not use the telephone to report a gas leak in the vicinity of the leak.

Do not connect your modem to a digital PBX (switchboard) system, because you

may damage the modem. Modems are designed to function with analog telephone

lines, such as residential lines. Do not connect your modem to an ISDN line. In

some areas, ISDN (digital) lines are being provided for residences and businesses.

These lines may damage the modem. Please note that this modem is fully compatible

with analog telephone lines that are connected to a Digital Exchange. Digital Ex-

changes are used in some areas to supply analog lines to homes and businesses.

Product Registration

The installation CD that came with your ActionLink Home Networking USB Cable

Single-Room Starter Kit contains a folder called Register. Inside this folder is a file

called “register.htm”. After installing the modem and its drivers, double-click on this

file. This will start up your browser and take you to the Actiontec web site:

http://www.actiontec.com/registration

Please fill in the required fields so that you can get prompt support and notification

of periodic product upgrades.

Product Features

This 56K* PnP (Plug-N-Play)† External Call Waiting Modem allows your computer

to connect to an ISP supporting V.90 or K56Flex™protocols (depending on your

model). This manual describes the hardware and software installation procedures for

your new 56K or external modem.

•Conforms to the ITU-T V.90 specification with auto-negotiation of V.90, V.34,

V.32bis, V.32, V.23, V.22bis, V.22, V.21, Bell 212A, and Bell 103 protocols.

•Supports Group 3: class 1 fax protocols.

•V.42bis and MNP 5 data compression. MNP2 - MNP4, V.42, and LAPM error

correction.

•Completely controller-based PCI modem for the widest range of supported

operating systems: DOS, Windows (3.1x, 95, 98, and NT), OS/2, UNIX, Linux

•Full-duplex

•Call Waiting

*The External 56K Call Waiting Modem is capable of 56K downloads. However, due to FCC rules which restrict the power output of

your ISP’s modems, current download speeds are limited to 53K bps. Depending on the conditions of your telephone lines, full 53K bps

connections may not be achieved. In these cases, you will achieve speeds up to 53K bps.

† “Plug-N-Play” installation is dependant upon your operating system and computer hardware. Some systems do not support Plug-N-

Play.

Getting Started

This package contains:

•External 56K Call Waiting Modem

•User’s Manual

•Voice/Fax Data Communications Software

•serial cable

•telephone cable

•power adapter

•A Bonus Software CD

BeforeYou Begin

Using the Telephone Answering Machine Functions with Windows 95

In order for the voice functions of the modem to work properly under 32-bit Tele-

phony API (TAPI) applications, you need to install the Unimodem V components

for Windows 95. This file needs to be copied and installed for earlier versions of

Windows 95. To find the Windows 95 version of your system, right-click the My

Computer icon on the windows desktop and chose Properties from the menu that

appears. A dialog box will appear displaying the version information for your instal-

lation of WIndows. Follow either 1 or 2 below.

1. If you have version 4.00.950 B

This is Windows 95 OEM Service Release 2, hereafter referred to as Windows

95B. You do not need to install the Unimodem V components as they are

already built into this version of windows. Proceed to “Installing the Modem.”

2. If you have version 4.00.950 or 4.00.950 A

The Unimodem V driver needs to be installed into Windows 95. Follow the

instructions below.

Step 1 Insert the modem’s CD into the CD-ROM drive. Double click on the ‘My

Computer’ icon, then again on the CD-ROM icon.

Step 2 In the window that appears, double-click on the Unimodem folder.

Step 2 From the new folder, find the icon for the UNIMODV.INF file and click

once to highlight it. Click the icon for the right mouse button. Choose

Install from the menu that appears. This will install the Unimodem drivers.

Step 3 Restart your computer. After Windows restarts with the drivers enabled,

you may proceed to “Installing the Modem.”

Installing the Modem

Installing the Interface Cables

The drawing below shows the back panel of the 56K External Call Waiting Modem

and the correct cable installation. The computer interface cable has both 9-pin and

25-pin serial port connectors for use on most computers See your computer owners

manual for the location and function of your serial (COM) ports.

Note: Connect only one connector (either 9 pin or 25 pin as appropriate) to your

computers serial (COM) port. Do not connect both.

Figure 1: Connecting the Cables

Modem Controls and Indicators

The front of the modem contains the power switch and modem indicator lights.

These are shown in the drawing below:

Figure 2: Modem Indicators and Controls

The power switch is a push-on/push-off type. This switch controls the ON and OFF

state of the modem. Please note that the external power adapter shown in fig. 1 also

needs to be correctly installed for power to be applied to the modem.

The LED (light emitting diode) indicators report modem status. They are:

CS (Clear to Send) On when CTS signal is active

RS (Request to Send) On when RTS signal is active

CD (Carrier Detect) On when remote carrier has been detected

OH (Off Hook) On when the modem is off hook

RD (Receive Data) On when the modem is receiving data

SD (Transmit Data) On when the modem is sending data

TR (Terminal Ready) On when DTR signal is active

MR (Modem Ready) On when power is applied to the modem

Device Driver Installation and Configuration

Configuring Windows 95

Step 1 Upon start-up, Windows 95 detects the modem and displays the New Hard-

ware Found dialog box. Select ‘Driver from disk provided by hardware

manufacturer’ then Click OK.

Step 2 Insert the modem’s installation CD-ROM. Change the drive letter that ap-

pears in the dialog box to the drive letter of your CD-ROM drive. Click

OK.

Step 3 After copying and installing the modem’s drivers, Windows will detect a

“Wave Device for Voice Modem”, displaying the dialog box below.

Step 4 With the modem’s installation CD-ROM still in the CD-ROM drive, click

OK.

Autres manuels pour External 56K Call Waiting

Table des matières

Autres manuels ActionTec Modem

ActionTec

ActionTec GT724WG Manuel utilisateur

ActionTec

ActionTec GT701-WG Manuel utilisateur

ActionTec

ActionTec UD800TP Manuel utilisateur

ActionTec

ActionTec V.92 Manuel utilisateur

ActionTec

ActionTec GT724WGR Manuel utilisateur

ActionTec

ActionTec 56K PCI Lite Modem HSP56I Manuel utilisateur

ActionTec

ActionTec GT701-WG Manuel utilisateur

ActionTec

ActionTec WirelessDSL Modem Manuel utilisateur

ActionTec

ActionTec 56K/V.92 Manuel utilisateur

ActionTec

ActionTec GT724WGR Manuel utilisateur

ActionTec

ActionTec 1520 Manuel d'utilisation

ActionTec

ActionTec PCI0839-01 Manuel utilisateur

ActionTec

ActionTec IS560LH Manuel utilisateur

ActionTec

ActionTec GT701D Manuel utilisateur

ActionTec

ActionTec GT724WG Manuel utilisateur

ActionTec

ActionTec Actiontec USB/Ethernet DSL Modem with Routing Capabilities... Manuel utilisateur

ActionTec

ActionTec Q1000Qwest Manuel utilisateur

ActionTec

ActionTec GT701-WG Manuel utilisateur

ActionTec

ActionTec External 56K Call Waiting Manuel utilisateur

ActionTec

ActionTec GT724WGR Manuel utilisateur

ActionTec

ActionTec Dual PC Modem R7000M Manuel utilisateur

ActionTec

ActionTec Plug n' Play Voice/Fax Modem V.90 ISA Manuel utilisateur

ActionTec

ActionTec GT784WN Manuel utilisateur

ActionTec

ActionTec 56K Internal PC Modem Manuel utilisateur

Manuels Modem populaires d'autres marques

Davicom

Davicom DM562AP Manuel utilisateur

EpiValley

EpiValley TATA indicom SXC-1080 Manuel utilisateur

Zte

Zte WiMAX Manuel utilisateur

Intelimax

Intelimax MA-2060 Manuel utilisateur

SMC Networks

SMC Networks D3CM1604V Manuel d'utilisation et d'entretien

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuel utilisateur

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuel utilisateur

Samsung

Samsung AceLink SAM-335A Manuel utilisateur

Enfora

Enfora Enabler-G Guide de configuration rapide

iRZ

iRZ ATM2-232 Manuel utilisateur

Zhone

Zhone 6310 Manuel utilisateur

Paradyne

Paradyne Hotwire 7976 Manuel utilisateur

US Robotics

US Robotics 3453C Manuel utilisateur

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuel utilisateur

Zte

Zte MF823 Manuel utilisateur

Four-Faith

Four-Faith F1403 Manuel utilisateur

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuel utilisateur

Gemtek

Gemtek WiMAX WIXFBR-103 Manuel utilisateur