ACTi ACM-1310 series Manuel utilisateur

IP Indoor IR Bullet Camera

(with DC 12V / PoE)

ACM-1310 series

Ver. 061101

Quick Installation Guide

0-1

0Getting Started

1.1 PACKAGE CONTENTS

ACM-1310 series Power Adaptor (Option)

(DC12V / PoE)

Product CD Terminal Block for Power

Warranty Card

0-2

1.2 PHYSICAL DESCRIPTION

1. Audio Input / Output

The IP device supports audio input and output with earphone jack

2. Power Input

If your power input is DC12V. Please follow the description on

the connector to connect to power.

3. Ethernet Port

The IP device connects to the Ethernet via a standard RJ45

connector. Supporting NWAY, this IP device can auto detect the

speed of local network segment (10Base-T/100Base-TX

Ethernet).

4. Reset Button

Step 1: Switch off IP device by disconnecting the power cable

PIN NAME DESCRIPTION

1 12V DC Power Input

2 GND Ground Pin

0-3

Step 2: Press and continue to hold the Reset Button. Reconnect

the power cable while continuing to hold the reset button.

Step 3: Keep holding the reset button depressed around 6 seconds,

release the reset button. The unit will start up with factory default

settings.

5. Analog Video Output

The IP outdoor rugged dome supports one channel analog video

output.

0-4

1.3 BASIC CONNECTIONS

Follow the procedures below to connect the IP device to the respective

apparatuses.

1. Connect an analog monitor to IP device video out (BNC connector).

2. Connect the power adaptor to IP device

3. Connect IP device’s ethernet port to an Ethernet (RJ45 connectors). If your

IP device has PoE built-in, you can regard it as a PD and connect it

directly to a PSE device like PoE switch.

4. Connect a PC to the Ethernet hub (RJ45 connectors)

NOTE: You may find a support package for help you getting familiar

with PoE. Please visit our web site, and get the support document

TS-00040.

1-5

1Quick Tour

This section guides you with a quick tour on this IP device.

2.1 Configure this IP Device

2.1.1 Make sure network environment

Default IP of this IP device is 192.168.0.100. Please make sure this IP device and

your PC are on the same network segment before running the installation.

Please set the settings as below.

IP address: 192.168. 0.xxx

Subnet mask: 255.255.255. 0

(NOTE: xxx should be a number

from 1 to 254, but 100 is

excepted.)

1-6

2.1.2 Open Internal Explorer with IP address

NOTE: If your web browser is earlier than IE6, then download IE6 is

recommended.

NOTE: This IP device default IP address is set to 192.168.0.100

2.1.3 Login with default administrator’s account & password

NOTE: Default administrator account is set to Admin, password is set to

123456, and click button.

1-7

2.1.4 Preview the video

2.1.5 Set the new IP address

1-8

*IP Address : The default IP address is 192.168.0.100.

*Subnet Mask : The default subnet mask is 255.255.255.0

*Click button

NOTE: In your Client PC, please make sure the setting of Network

Connections Type is set to Auto Negotation, since this IP device follows

MII standard. Otherwise, you might not see the live image.

IMPORTANT: After the IP address is changed, please record this IP

address. There’s no way to connect to the IP device if user forgets the

new IP address.

2.1.6 Check Default Video Setting

NOTE: Please make sure the TV Input (NTSC / PAL) is meet your

requirement, and click button.

2.1.7 Click Save Reboot to restore all settings and please wait about 30 seconds

for system reboot.

Table des matières

Autres manuels ACTi Caméra IP

ACTi

ACTi KCM-5311 Instructions d'utilisation

ACTi

ACTi CAM-5100M Manuel utilisateur

ACTi

ACTi ACM-4100 series Manuel utilisateur

ACTi

ACTi ACM-8511 Manuel utilisateur

ACTi

ACTi CAM-5100M Manuel utilisateur

ACTi

ACTi ACM-3401 Series Manuel utilisateur

ACTi

ACTi ACM-1430 series Instructions d'utilisation

ACTi

ACTi CAM-5120 Manuel utilisateur

ACTi

ACTi ACM-5611 Instructions d'utilisation

ACTi

ACTi TCM-7811 Instructions d'utilisation

ACTi

ACTi ACM-5801 Instructions d'utilisation

ACTi

ACTi KCM-7911 Instructions d'utilisation

ACTi

ACTi ACM-4201 Instructions d'utilisation

ACTi

ACTi ACM-4000 Instructions d'utilisation

ACTi

ACTi ACM-4200 series Instructions d'utilisation

ACTi

ACTi TCM-3111 Manuel utilisateur

ACTi

ACTi TCM-4301 Manuel utilisateur

ACTi

ACTi KCM-7911 Manuel utilisateur

ACTi

ACTi CAM-5120 Manuel utilisateur

ACTi

ACTi CAM-5300H Manuel utilisateur

ACTi

ACTi ACM-4200 series Manuel utilisateur

ACTi

ACTi ACM-5811 series Manuel utilisateur

ACTi

ACTi ACM-1511 Series Instructions d'utilisation

ACTi

ACTi TCM-4301 Manuel utilisateur

Manuels Caméra IP populaires d'autres marques

FLIR

FLIR Exx series Manuel utilisateur

Avigilon

Avigilon H4A-BO1-IR Manuel utilisateur

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuel utilisateur

ShareTech

ShareTech AV1 Manuel utilisateur

Ezviz

Ezviz C6C Manuel utilisateur

Melchioni

Melchioni UCAM 2015 Manuel utilisateur

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuel utilisateur

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuel utilisateur

Mitel

Mitel 6800i Series Manuel de service

Vitek

Vitek VTC-IR403-212NP Manuel utilisateur

THOMSON

THOMSON DSC - 323W Manuel utilisateur

AVer

AVer FB2027 Manuel utilisateur

ENFORCER

ENFORCER EV-T5105-N2SQ Manuel utilisateur

Wansview

Wansview NC543 Manuel utilisateur

Eneo

Eneo MCB-64A0003M0A Manuel utilisateur

deView electronics

deView electronics CBDNI36F Manuel utilisateur

Swann

Swann SwannEye Manuel utilisateur

LevelOne

LevelOne IP CamSecure Manuel utilisateur