ACME VB-8-10FC Manuel utilisateur

VBar Integral

VB-4-10FC

VB-8-10FC

User Manual

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions

2. Technical Specifications

3. Installation

4. How To Set The Fixture

5. How To Control The Fixture

6. DMX 512 Configuration

7. DMX 512 Connections

8. Troubleshooting

9. Fixture Cleaning

1. Safety Introductions

WARNING

Please keep this User Manual for future consultation. If you sell the unit to another user,

be sure that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the

power requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

Disconnect mains power before fuse replacement or servicing.

Make sure there are not flammable materials close to the unit while operating as it is fire

hazard.

Use safety cable when fixes this unit.

Maximum ambient temperature is TA: 40℃and don’t operate it where the temperature

is higher than this.

There are no user serviceable parts inside the fixture. Do not open the housing or

attempt any repairs by yourself. In the unlikely event your fixture may require service,

please contact the nearest authorized technical assistance center and always use the

same type spare parts. .

Don’t connect the device to any dimmer pack or power pack.

Do not look directly at the LED light beam while the fixture is on.

The housing must be replaced if they are visibly damaged.

Do not touch any wire during operation as high voltage might be causing electric shock.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

2. Technical Specifications

VB-4-10FC

Voltage: 100~250V 50/60Hz

Power Consumption: 46W

LEDs: 4 X 10W(RGBW)

IP:66

Dimension: 637 x 79 x 126 mm

Weight: 4kg

VB-8-10FC

Voltage:100~250V 50/60Hz

Power Consumption: 89 W

LEDs: 8 X 10W(RGBW)

IP:66

Dimension:1238 x 79 x 126 mm

Weight: 5.5kg

3. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of

the unit’s weight.

The equipment must be fixed by professionals. And it must be fixed at a place where is out

of the touch of people and has no one pass by or under it.

4. How To Set The Fixture

4.1 Main Function

Unscrew the 4 screws shown on the diagram,

move the cover away to set the unit.

Press MENU button to enter menu mode, press

DOWN and UP button until the required one is shown on the display. Select the function by

ENTER button and the display will blink. Use DOWN and UP button to change the mode.

Once the required mode has been selected, press ENTER button to setup or it will

automatically return to the main functions without any change after idling one minute. Back

to the functions without any change press MENU button. The main functions are shown

below:

DMX 512 Address Setting

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX 512 address.

Once the address has been selected, press ENTER button to setup (or automatically exit

menu mode after idling one minute). To go back to the main functions press the MENU

button.

Channel Mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the (4

channels) or (5 channels) or (7 Channels) mode. Once the mode

has been selected, press the ENTER button to setup (or automatically exit menu mode after

idling one minute). To go back to the main functions press the MENU button.

Show 1~16

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (show 1) or (Show 2)

or … or (show 16). Press ENTER button to confine, (fade time) will

blinking on the display, use DOWN and UP button to adjust the fade time, press ENTER

button to setup and (wait time) will blinking on the display, use DOWN and UP

button to adjust the wait time, press ENTER button to setup (or automatically exit menu

mode after idling one minute). Back to the previous functions without any change press

MENU button.

Blackout mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (blackout) or (normal).

Once select, press ENTER button to setup (or automatically exit menu mode after idling one

minute). To go back to the main functions press the MENU button.

Manual Test

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the , ,

, , (dimmer) or (strobe). Press ENTER button to confine

and use DOWN and UP button to adjust the values. Once select, press the ENTER button to

setup (or automatically exit menu mode after idling one minute). Back to the previous

functions without any change press MENU button.

White Balance

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the , ,

, press ENTER button to confine and use DOWN and UP button to adjust white

balance. Once select, press ENTER button to store (or automatically exit menu mode after

idling one minute). Back to the previous functions without any change press MENU button.

Display Inverse

Press MENU button until is blinking on the display. Use DOWNand UP button to

select (display normal) or (display inverse), Once select, press ENTER

button to store (or automatically exit menu mode after idling one minute). To go back to the

main functions press the MENU button.

Self-Test

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the unit will run the built-in programmer for self-test. To go back to the main

functions press the MENU button.

LED on/off

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the (LED

display always on) or ( LED display off one minute after exit menu mode). Once

select, press ENTER button to store (or automatically exit menu mode after idling one

minute). To go back to the main functions press the MENU button.

Fixture Hours

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the display will show the number of working hours of the unit. To go back to the

main functions press the MENU button.

Software version

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the display will show the software version of the unit. To go back to the main

functions press the MENU button again.

5. How To Control The Unit

You can operate the unit in two ways:

1. By master/slave built-in preprogram function

2. By DMX controller

No need to turn the unit off when you change the DMX address, as new DMX address

setting will be effected at once. Every time you turn the unit on, it will move all the motors to

their ‘home’position and you may hear some noises for about 20 seconds. After that the unit

will be ready to receive DMX signal or run the built-in programs.

5.1 Master/Slave Built In Preprogrammed Function

By linking the units in master/slave connection, the first unit or master unit will control the

other units to give an automatic light show. This function is good when you want an instant

show. You have to select (show 1) or (show 2) or (show 3) …or

(show 16) for the first unit. Its DMX input jack will have nothing plugged into it. The

other units will automatically be slave units, their DMX input jacks will connect with the DMX

output jacks of the last units.

5.2 DMX Controller

Use universal DMX controller to control the units, you have to set DMX address from 1 to

512 channel so that the units can receive DMX signal.

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX 512 address.

Once the address has been selected, press ENTER button to setup (or automatically exit

menu mode after idling one minute). To go back to the main functions press the MENU

button. Please refer to the following diagram to address your DMX512 channel for the first 4

units.

4 channels:

4D channels:

4C channels:

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ACME Luminaire

ACME

ACME GLAMOUR 700Z RGBY Manuel utilisateur

ACME

ACME Led Strobe 20 LED-ST20 Manuel utilisateur

ACME

ACME COOLIE 545 Manuel utilisateur

ACME

ACME Xperior 5R BEAM F Manuel utilisateur

ACME

ACME led-st05 Manuel utilisateur

ACME

ACME MH-6616S Manuel utilisateur

ACME

ACME XP-5000 SZ NF Manuel utilisateur

ACME

ACME xperior 15R spot XP-15R SZ Manuel utilisateur

ACME

ACME GEIST BEAM Manuel utilisateur

ACME

ACME LED BEAM 350 Manuel utilisateur

ACME

ACME LED-MB500 Manuel utilisateur

ACME

ACME CM-70Z Manuel utilisateur

ACME

ACME Xperior 5R BEAM F Manuel utilisateur

ACME

ACME Xperior XP-16R BEAM II Manuel utilisateur

ACME

ACME LPB-4P Manuel utilisateur

ACME

ACME Xperior XP-16R SZ Manuel utilisateur

ACME

ACME Aeco 20 Manuel utilisateur

ACME

ACME LED?MS700PE Manuel utilisateur

Manuels Luminaire populaires d'autres marques

Emos

Emos CLASSIC ZY1431T Manuel utilisateur

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuel utilisateur

Hedler

Hedler C 12 silent Manuel utilisateur

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuel utilisateur

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuel utilisateur

Lightmaxx

Lightmaxx Shaft 5R Manuel utilisateur

Triarch

Triarch 31083 Manuel utilisateur

Philips

Philips 32614 Series Manuel utilisateur

IKEA

IKEA TIVED Manuel utilisateur

Lightolier

Lightolier LP200 Manuel utilisateur

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Cooper Lighting

Cooper Lighting Halo L3232E Manuel utilisateur

Stageline

Stageline ODW-2410RGBW Manuel utilisateur

Light Sky

Light Sky Tornado Series Manuel utilisateur

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuel utilisateur

Lightolier

Lightolier Lytespan 83ED17S Manuel utilisateur

Lightolier

Lightolier Calculite CS8226 Manuel utilisateur