Abocom ISM56CR Manuel utilisateur
M73-APO02-300
Internal
Fax Modem 56K
Quick Installation Guide
- 1 -
FCC REGULATORY STATEMENTS
FCC Part 68 Registration
This device complies with FCC Part 68 rules, and the use of
this device is subject to the following restrictions:
1. The FCC has established rules which permit this device to
be directly connected to the telephone network.
Standardized jacks are used for these connections. This
equipment should not be used on party lines or coin
phones.
2. If this device is malfunctioning, it may also be causing
harm to the telephone network; this device should be
disconnected until the source of the problem can be
determined and until repair has been made. If this is not
done, the telephone company may temporarily disconnect
service.
3. The telephone company may make changes in it's facilities,
equipment, operation and procedures; if such changes
affect the compatibility or use of this device, the telephone
company is required to give adequate notice of the
situation with the FCC.
4. If the telephone company requests information on what
equipment is connected to their lines, inform them of:
a. The telephone number to which this unit is connected.
b. The Ringer Equivalence Number (REN).
c. The USOC jack required.
d. The FCC Registration number.
Items (b) and (d) are indicated on the label. The Ringer
Equivalence Number (REN) is used to determine how many
devices can be connected to your telephone line. In most
areas, the sum of the REN's of all the devices on any one line
should not exceed 5.0. If too many devices are attached, they
may not ring properly.
FCC Part 15 Registration
This device complies with Part 15 of FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interface, and
2. This device must accept any interface received including
interface that may cause undesired operation.
- 2 -
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and
receiver
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult an experienced radio/TV technician for help.
CTR 21 pan-European Certification
This equipment has been approved in accordance with
Council Decision 98/482/EC for pan-European single
terminal connection to the public switched telephone network
(PSTN). However, due to differences between the individual
PSTNs provided in different countries, the approval does not,
of itself, give an unconditional assurance of successful
operation on every PSTN network termination point. In the
event of problems, you should contact your equipment
supplier in the first instance.
This device is designed to work with the notified networks in
all EC member states. Nevertheless, some of the network
services in individual countries might not be supported, but
they will not affect the normal data and fax applications. For
example, the metering charge service in Germany. Besides
you may encounter difficulty of using PULSE dialing
function in some of the countries, such as Nordic countries.
This kind of network compatibility is dependent on the
- 3 -
physical and software settings of this device. If the users are
desired to use this device on those networks, they should
contact the vendor or supplier first.
-
Table of Contents
HARDWARE INSTALLATION ................... 1
SOFTWARE INSTALLATION..................... 2
WINDOWS 95/98/98SE
INSTALLATION................................................ 2
WINDOWS 2000 INSTALLATION ..................... 4
WINDOWS ME INSTALLATION........................ 7
WINDOWS XP INSTALLATION ........................ 9
WINDOWS NT INSTALLATION ...................... 15
HARDWARE INSTALLATION
Precautions:
Please be sure you take adequate anti-static
precautions when handling this product. The
simplest way to achieve this is; before you begin
and every minute or so during the hardware
installation touch a non-painted surface of the
computer’s chassis.
1. Before installing the device, make sure the
computer is turned off.
2. Remove the expansion slot cover from the
computer.
3. Carefully slide the PCI modem card into an
available PCI slot, push it evenly and firmly
home and ensure it is screwed securely in
place using the mounting screw (PCI slots
are 85mm long and positioned 40mm from
the PC’s rear panel. Generally there are
several PCI slots side by side).
4. Plug one end of the telephone cable into the
Modem line jack and the other end to the
telephone jack in the wall.
5. Replace the cover.
6. After hardware installation is done, move on
to the software installation.
-1-
SOFTWARE INSTALLATION
Windows 95/98/98SE Installation
1. Restart the computer system after the
modem is correctly plugged into the PCI
slot of your computer. Windows will
automatically detect the device. Click Next.
2. When the following dialog box appears,
insert the device driver compact disc into
your CD-ROM drive and click Next.
3. Select Specify a location and press Browse
to choose the folder driver/win95/98 in
your CD-ROM drive. Then click Next.
-2-
-3-
4. Click Next to continue.
5. When the following figure appears, click
Finish. The Installation program will
continue.
-4-
6. The program will proceed automatically.
Click Finish to complete software
installation.
Windows 2000 Installation
1. Restart the computer system after the
modem is correctly plugged into the PCI
slot of your computer. Windows will
automatically detect the device. Click Next.
-5-
2. Follow the on-screen instructions to proceed.
(Click Next to continue.)
3. Select Specify a Location. Click the Next
button.
4. Load the Compact Disc that contains the
device driver into your CD-ROM drive.
Click Browse and select the proper file
Table des matières
Autres manuels Abocom Modem
Abocom
Abocom AFM-102 Manuel utilisateur
Abocom
Abocom AFM-102 Manuel utilisateur
Abocom
Abocom UFM560 Manuel utilisateur
Abocom
Abocom EFM560 Manuel utilisateur
Abocom
Abocom USB ADSL Modem UAM700 Manuel utilisateur
Abocom
Abocom EFM560 Manuel utilisateur
Abocom
Abocom FM560C Manuel utilisateur
Abocom
Abocom IFM560B Manuel utilisateur
Abocom
Abocom FM56CC Manuel utilisateur
Abocom
Abocom IFM560 Manuel utilisateur
Abocom
Abocom IAM800 Manuel utilisateur
Abocom
Abocom ISM56CL Manuel utilisateur
Abocom
Abocom Internal Fax Modem 56K Manuel utilisateur
Abocom
Abocom UTA128 Manuel utilisateur
Abocom
Abocom MC-56SVV Manuel utilisateur
Abocom
Abocom FM560MX Manuel utilisateur
Abocom
Abocom EFM56CC Manuel utilisateur
Abocom
Abocom Harley RS232/USB Modem Moudle AFM-100 Manuel utilisateur
Abocom
Abocom ULF560 Manuel utilisateur
Abocom
Abocom UCM56CR Manuel utilisateur
Manuels Modem populaires d'autres marques
Davicom
Davicom DM562AP Manuel utilisateur
EpiValley
EpiValley TATA indicom SXC-1080 Manuel utilisateur
Zte
Zte WiMAX Manuel utilisateur
Intelimax
Intelimax MA-2060 Manuel utilisateur
SMC Networks
SMC Networks D3CM1604V Manuel d'utilisation et d'entretien
Telstra
Telstra Wi-Fi 4G Advanced Pro X Manuel utilisateur
US Robotics
US Robotics 3453C Manuel utilisateur
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuel utilisateur
Zte
Zte MF823 Manuel utilisateur
Four-Faith
Four-Faith F1403 Manuel utilisateur
Sierra Wireless
Sierra Wireless AIRLINK MP595W Manuel utilisateur
Gemtek
Gemtek WiMAX WIXFBR-103 Manuel utilisateur