Abit BX6 Manuel utilisateur

Notice

The information in this document is subject to change without notice and

does not represent a commitment on part of the vendor, who assumes no

liability or responsibility for any errors that may appear in this manual.

No warranty or representation, either expressed or implied, is made with

respect to the quality, accuracy or fitness for any particular part of this

document. In no event shall the manufacturer be liable for direct, indirect,

special , incidental or consequential damages arising from any defect or error

in this manual or product.

Product names appearing in this manual are for identification purpose only

and trademarks and product names or brand names appearing in this

document are property of their respective owners.

This document contains materials protected under International Copyright

transmitted or transcribed without the expressed written permission of the

manufacturer and authors of this manual.

Part No:MN-133-2A1-41 Rev:1.01

BX6 Motherboard

USER’S MANUAL

Table of Contents

Chapter 1 Introduction of BX6 Features 1-1

(1) Specifications 1-1

(2) Layout Diagram 1-3

(3) The System Block Diagram 1-4

Chapter 2 Installing the Motherboard 2-1

(1) Installing the Motherboard to the Casing 2-2

(2) Standard External Connectors 2-3

(3) Jumper and Switches 2-9

(4) Installation of the PentiumII/III, CeleronCPU 2-11

(5) Installing System Memory 2-12

Chapter 3 Introduction of BIOS 3-1

(1) CPU Setup <CPU SOFT MENU™

II> 3-3

(2) Standard CMOS Setup Menu 3-8

(3) BIOS Features Setup Menu 3-11

(4) Chipset Features Setup Menu 3-17

(5) Power Management Setup Menu 3-21

(6) PnP/PCI Configuration 3-28

(7) Load Setup Defaults 3-31

(8) Integrated Peripherals 3-32

(9) Password Setting 3-37

(10) IDE Hard Disk Detection 3-37

(11) Save & Exit Setup 3-38

(12) Exit Without Saving 3-38

Appendix A Quick Installation A-1

Appendix B General Discussion About HDD Installation B-1

Appendix C BIOS Flashing User Instructions C-1

Appendix D How to install the IDE Bus Master driver D-1

Appendix E How to install the PCI bridge driver for the 440BX chipset E-1

Appendix F Install HighPoint XStore Pro Utility F-1

Appendix G Install Winbond Hardware Doctor Utility G-1

Appendix H Technical Support H-1

Introduction of BX6 Features 1-1

Chapter 1 Introduction of BX6 Features

The motherboard is designed for a new generation CPUs. It supports the Intel

SLOT1 structure (PentiumII/III and Celeronprocessors), up to 1GB of memory,

super I/O, and Green PC functions. The motherboard provides high performance

for server systems and meets the requirements for desktop system for multimedia

in the future.

(1) Specifications

1. CPU

qCPU SOFT MENU™II eliminates the need for jumpers or DIP switches

needed to set CPU parameters

qEmploys switching type regulators to stabilize CPU operation

qSupports 66 and 100MHz MHz CPU external clock speeds

qSupports Intel®

Pentium®

III450 ~ 500MHz processor cartridge (Based on

100MHz)

qSupports Intel®

Pentium®

II 350 ~ 450MHz processor cartridge (Based on

100MHz) and Pentium®

II 233 ~ 333MHz processor cartridge (Based on

66MHz)

qSupports Intel®

Celeron®

266~433MHz processor (Based on 66MHz)

2. Chipset

qIntel®

440BX chipset (82443BX and 82371EB)

qSupports Ultra DMA/33 IDE protocol

qSupports Advanced Configuration and Power Management Interface(ACPI)

qAccelerated Graphics Port connector supports AGP 1x and 2x mode

(Sideband) 3.3V device

3. Cache Memory

qLevel 1 and Level 2 cache built into Intel®

Pentium®

II/III processor cartridge

qLevel 1 cache (without L2 cache) built into Intel®

CeleronprocessorŒ

4. Memory(System Memory)

qFour 168-pin DIMM sockets support SDRAM modules

qSupports up to 1GB

qECC support

q6 Data Buffers

5. System BIOS

qAWARD BIOS

qSupports Plug-and-Play (PnP)

qSupports Advanced Configuration Power Interface (ACPI)

qSupports Desktop Management Interface (DMI)

qYear 2000 compliant

Chapter 11-2

Multi I/O Functions

qFloppy port supports up to 2.88MB, and 3 mode floppies

qUltra DMA/33 bus master IDE supports up to 4 IDE devices ( Including LS-

120 MB floppy drive )

qBuilt-in Standard/EPP/ECP parallel port connector

qTwo built-in 16550 fast UART compatible serial port connectors

qBuilt-in PS/2 keyboard and PS/2 mouse port connectors

qBuilt-in standard IrDA TX/RX header

qTwo built-in USB connectors

Miscellaneous

qATX form factor

qOne AGP slot, Five PCI slots and Two ISA slots

qWake Up On LAN header

qSB-LINK header

qHardware monitoring¡GIncluded fan speed, voltages, CPU and system

environment temperature

qKeyboard Wake Up or PS/2 Mouse Wake Up (need +5VSB at least720mA)

qBoard size: 305 * 210mm

Note:

All brand names and trademarks are the property of their respective owners.

ŒThe actual specs of Intel®

Celeron®

processor will depend on Intel’s shipping specs.

¯Above 66MHz/100MHz bus speed supported but not guaranteed due to the PCI and chipset

specs.

¯Sound Blaster™

is a registered trademark of Creative Technology Ltd.in the United States

and certain other countries. Sound Blaster - LINK™

and SB-LINK™are trademarks of

Creative Technology Ltd.

¯Specifications and information contained in this manual are subject to change without

notice.

Introduction of BX6 Features 1-3

(2) Layout Diagram

Figure 1-1 Motherboard Component Locations

Chapter 11-4

(3) The System Block Diagram

Installing the Motherboard 2-1

Chapter 2 Installing the Motherboard

This BX6 motherboard not only provides all standard equipment for classic

personal computers, but also provides great flexibility for meeting future upgrade

demands. This chapter will introduce step by step all the standard equipment

and will also present, as completely as possible, future upgrade capabilities. This

motherboard is able to support all IntelPentiumII/III processors and Intel

Celeronprocessor now on the market. (For details, see specifications in

Chapter 1.)

This chapter is organized according the following features:

(1) Installing the Motherboard to the Casing

(2) Standard external connectors

(3) Jumpers and switches

(4) Installation of the PentiumII/III, CeleronCPU

(5) Installing the system memory

NNNN

Before proceeding with the installation

Before installing the motherboard please be sure to turn off or disconnect the

power supply unit. Before making any modifications to the hardware

configuration of the motherboard, the power supply to any areas of the

motherboard you plan to modify should be turned off to avoid unnecessary

damage to the hardware.

User friendly instructions

Our objective is to enable the novice computer user to perform the installation by

themselves. We have attempted to write this document in a very clear, concise

and descriptive manner to help overcome any obstacles you may face during

installation. Please read our instructions carefully and follow them step-by-step.

Chapter 22-2

(1) Installing the Motherboard to the Casing

Most computer cases will have a base on which there will be many mounting

holes that allows the motherboard to be securely attached and at the same time,

prevents short circuits.

There are two ways to attach the motherboard to the base.

lwith spacers

lor with bolts

Please refer to the figure below that shows the studs and spacers, they may have

several types, but all look like the figures below:

Figure 2-1. The outline of stud and spacer

In principle, the best way to attach the motherboard is with bolts, and only if you

are unable to do this should you attach the board with spacers. Take a careful look

at the motherboard and you will see many mounting holes on it. Line these holes

up with the mounting holes on the base. If the holes line up, and there are screw

holes this means you can attach the motherboard with bolts. If the holes line up

and there are only slots, this means you can only attach the motherboard with

spacers. Take the tip of the spacers and insert it into the slots. After doing this to

all the slots, you can slide the motherboard into position aligned with the slots.

After the motherboard has been positioned, check to make sure everything is OK

before putting the casing back on.

Note: If the motherboard has mounting holes, but don’t line up with the holes on the base and

their are no slots to attach the spacers, don’t worry, you can still attach the spacers to

the mounting holes. Just cut the spacers (along the dotted line) (the spacer may be a

little hard so be careful of our hands). In this way you can still attach the motherboard

to the base without worrying about short circuits.

Autres manuels pour BX6

Table des matières

Autres manuels Abit Carte mère

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur