ABB IRB 2600 Series Manuel utilisateur

Product manual

IRB 2600

Trace back information:

Workspace R15-1 version a3

Checked in 2015-03-25

Skribenta version 4.1.349

Product manual

IRB 2600 - 20/1.65

IRB 2600 - 12/1.65

IRB 2600 - 12/1.85

IRB 2600ID - 15/1.85

IRB 2600ID - 8/2.0

M2004

Document ID: 3HAC035504-001

Revision: G

The information in this manual is subject to change without notice and should not

be construed as a commitment by ABB. ABB assumes no responsibility for any errors

that may appear in this manual.

Except as may be expressly stated anywhere in this manual, nothing herein shall be

construed as any kind of guarantee or warranty by ABB for losses, damages to

persons or property, fitness for a specific purpose or the like.

In no event shall ABB be liable for incidental or consequential damages arising from

use of this manual and products described herein.

This manual and parts thereof must not be reproduced or copied without ABB's

written permission.

Additional copies of this manual may be obtained from ABB.

The original language for this publication is English. Any other languages that are

supplied have been translated from English.

ABB AB

Robotics Products

Se-721 68 Västerås

Sweden

Table of contents
9Overview of this manual ...................................................................................................................
15Product documentation, IRC5 ..........................................................................................................
17How to read the product manual ......................................................................................................
191 Safety
191.1 Introduction to safety information ......................................................................... 201.2 General safety information .................................................................................. 201.2.1 Introduction to general safety information .................................................... 211.2.2 Safety in the robot system ........................................................................ 221.2.3 Safety risks ............................................................................................ 221.2.3.1 Safety risks during installation and service work on robots .................. 251.2.3.2 CAUTION - Hot parts may cause burns! ........................................... 261.2.3.3 Safety risks related to tools/work pieces .......................................... 271.2.3.4 Safety risks related to pneumatic/hydraulic systems .......................... 281.2.3.5 Safety risks with pressure relief valve .............................................. 291.2.3.6 Safety risks during operational disturbances ..................................... 301.2.3.7 Risks associated with live electric parts ........................................... 321.2.4 Safety actions ......................................................................................... 321.2.4.1 Safety fence dimensions ............................................................... 331.2.4.2 Fire extinguishing ........................................................................ 341.2.4.3 Emergency release of the robot arm ............................................... 351.2.4.4 Brake testing .............................................................................. 361.2.4.5 Risk of disabling function "Reduced speed 250 mm/s" ........................ 371.2.4.6 Safe use of the jogging device ....................................................... 381.2.4.7 Work inside the working range of the robot ....................................... 391.2.4.8 Signal lamp (optional) ................................................................... 401.2.5 Safety stops ........................................................................................... 401.2.5.1 What is an emergency stop? .......................................................... 421.3 Safety related instructions .................................................................................. 421.3.1 Safety signals in the manual ...................................................................... 441.3.2 Safety symbols on product labels ............................................................... 491.3.3 DANGER - Moving robots are potentially lethal! ............................................ 501.3.4 DANGER - First test run may cause injury or damage! ................................... 511.3.5 WARNING - The brake release buttons may be jammed after service work ........ 521.3.6 DANGER - Make sure that the main power has been switched off! .................... 531.3.7 WARNING - The unit is sensitive to ESD! ..................................................... 541.3.8 WARNING - Safety risks during handling of batteries ..................................... 551.3.9 WARNING - Safety risks during work with gearbox lubricants (oil or grease) ......
572 Installation and commissioning
572.1 Introduction ...................................................................................................... 582.2 Unpacking ....................................................................................................... 582.2.1 Pre-installation procedure ......................................................................... 622.2.2 Working range and type of motion .............................................................. 672.2.3 Risk of tipping/stability ............................................................................. 682.3 On-site installation ............................................................................................ 682.3.1 Lifting robot with roundslings .................................................................... 712.3.2 Lifting and turning a suspended mounted robot ............................................ 722.3.3 Setting the system parameters for a suspended or tilted robot ......................... 752.3.4 Manually releasing the brakes ................................................................... 782.3.5 Orienting and securing the robot ................................................................ 822.3.6 Fitting equipment on robot ........................................................................ 942.3.7 Loads fitted to the robot, stopping time and braking distances ......................... 952.4 Restricting the working range .............................................................................. 952.4.1 Introduction ............................................................................................ 962.4.2 Mechanically restricting the working range of axis 1 ......................................
Product manual - IRB 2600 5
3HAC035504-001 Revision: G
© Copyright 2009-2015 ABB. All rights reserved.
Table of contents

982.5 Installing options ............................................................................................... 982.5.1 Installation of cooling fan for motors (option) ................................................ 1022.5.2 Installing an expansion container ............................................................... 1042.5.3 Installation of Foundry Plus Cable guard (option no. 908-1) ............................. 1052.5.4 Installation of signal lamp (option) .............................................................. 1062.6 Robot in hot environments .................................................................................. 1062.6.1 Start of robot in hot environments .............................................................. 1072.7 Robot in cold environments ................................................................................. 1072.7.1 Start of robot in cold environments ............................................................. 1082.8 Electrical connections ........................................................................................ 1082.8.1 Robot cabling and connection points .......................................................... 1102.8.2 Customer connection on robot ................................................................... 1122.8.3 Customer connections on upper arm ..........................................................
1153 Maintenance
1153.1 Introduction ...................................................................................................... 1163.2 Maintenance schedule and expected component life ............................................... 1163.2.1 Specification of maintenance intervals ........................................................ 1173.2.2 Maintenance schedule ............................................................................. 1203.2.3 Expected component life ......................................................................... 1213.3 Inspection activities ........................................................................................... 1213.3.1 Inspecting oil level, axis-1 gearbox ............................................................ 1283.3.2 Inspecting the oil level, axis 2 gearbox ........................................................ 1303.3.3 Inspecting the oil level, axis 3 gearbox ........................................................ 1323.3.4 Inspecting the oil level, axis 4 gearbox ........................................................ 1343.3.5 Inspecting oil level, gearbox axes 5 - 6 ........................................................ 1363.3.6 Inspecting the cable harness ..................................................................... 1383.3.7 Inspecting information labels ..................................................................... 1403.3.8 Inspecting the mechanical stop pin, axis 1 ................................................... 1433.3.9 Inspecting additional mechanical stops ....................................................... 1453.3.10 Inspecting dampers ................................................................................. 1473.3.11 Inspecting the pressure relief valve ............................................................ 1493.3.12 Inspecting Signal lamp (option) .................................................................. 1513.4 Replacement / Changing activities ........................................................................ 1513.4.1 Type of lubrication in gearboxes ................................................................ 1533.4.2 Changing the oil, axis 1 gearbox on floor mounted robots ............................... 1583.4.3 Changing the oil, axis-1 gearbox on suspended robots ................................... 1643.4.4 Changing the oil, axis-2 gearbox ................................................................ 1683.4.5 Changing the oil, axis-3 gearbox ................................................................ 1723.4.6 Changing the oil, axis-4 gearbox ................................................................ 1763.4.7 Changing oil, axes-5 and -6 gearboxes ........................................................ 1803.4.8 Replacing SMB battery ............................................................................. 1853.5 Cleaning .......................................................................................................... 1853.5.1 Cleaning the IRB 2600 ..............................................................................
1894 Repair
1894.1 Introduction ...................................................................................................... 1904.2 General procedures ........................................................................................... 1904.2.1 Performing a leak-down test ...................................................................... 1914.2.2 Mounting instructions for bearings ............................................................. 1934.2.3 Mounting instructions for seals .................................................................. 1954.3 Complete robot ................................................................................................. 1954.3.1 Removing the complete cable harness ........................................................ 2064.3.2 Refitting the complete cable harness .......................................................... 2214.3.3 Replacing the cable harness in the upper arm - IRB 2600ID ............................ 2324.3.4 Replacing SMB unit ................................................................................. 2374.3.5 Replacing the brake release unit ................................................................ 2414.3.6 Replacing the base ..................................................................................
6 Product manual - IRB 2600
3HAC035504-001 Revision: G
© Copyright 2009-2015 ABB. All rights reserved.
Table of contents

2494.4 Upper arm ....................................................................................................... 2494.4.1 Replacing the complete upper arm ............................................................. 2584.4.2 Replacing complete tubular shaft unit ......................................................... 2644.4.3 Replacing wrist unit ................................................................................. 2684.4.4 Measuring the play, axis 5 ........................................................................ 2704.4.5 Measuring the play, axis 6 ......................................................................... 2724.4.6 Measuring the play, axis 5 (ID upper arm) .................................................... 2754.4.7 Measuring the play, axis 6 (ID upper arm) .................................................... 2784.5 Lower arm ....................................................................................................... 2784.5.1 Replacing the lower arm ........................................................................... 2834.6 Frame and base ................................................................................................ 2834.6.1 Replacing stop pin axis 1 .......................................................................... 2864.7 Motors ............................................................................................................ 2864.7.1 Removing motors .................................................................................... 2984.7.2 Refitting motors ...................................................................................... 3144.7.3 Replacing motor axis 5 - IRB 2600ID ........................................................... 3254.7.4 Replacing motor axis 6 and wrist unit - IRB 2600ID ........................................ 3344.7.5 Adjusting the play ................................................................................... 3394.8 Gearboxes ....................................................................................................... 3394.8.1 Replacing gearbox axis 1 .......................................................................... 3454.8.2 Replacing gearbox axis 2 .......................................................................... 3544.8.3 Replacing gearbox axis 3 ..........................................................................
3615 Calibration information
3615.1 Introduction ..................................................................................................... 3625.2 Calibration methods ........................................................................................... 3645.3 Calibration scale and correct axis position ............................................................. 3675.4 Calibration movement directions for all axes .......................................................... 3685.5 Updating revolution counters ............................................................................... 3705.6 Checking the zero position ..................................................................................
3716 Decommissioning
3716.1 Introduction ...................................................................................................... 3726.2 Environmental information .................................................................................. 3736.3 Scrapping of robot .............................................................................................
3757 Reference information
3757.1 Introduction ...................................................................................................... 3767.2 Applicable safety standards ................................................................................ 3787.3 Unit conversion ................................................................................................. 3797.4 Screw joints .................................................................................................... 3827.5 Weight specifications ......................................................................................... 3837.6 Standard tools .................................................................................................. 3847.7 Special tools .................................................................................................... 3867.8 Lifting accessories and lifting instructions ..............................................................
3878 Spare part lists
3878.1 Spare part lists and illustrations ...........................................................................
3899 Circuit diagram
3899.1 Circuit diagrams ................................................................................................
391Index
Product manual - IRB 2600 7
3HAC035504-001 Revision: G
© Copyright 2009-2015 ABB. All rights reserved.
Table of contents

This page is intentionally left blank

Overview of this manual

About this manual

This manual contains instructions for:

• mechanical and electrical installation of the robot

• maintenance of the robot

• mechanical and electrical repair of the robot.

The manual also contains reference information for all procedures detailed in the

manual.

Usage

This manual should be used during:

• installation, from lifting the robot to its work site and securing it to the

foundation, to making it ready for operation

• maintenance work

• repair work and calibration.

Who should read this manual?

This manual is intended for:

• installation personnel

• maintenance personnel

• repair personnel.

Prerequisites

A maintenance/repair/installation craftsman working with an ABB Robot must:

• be trained by ABB and have the required knowledge of mechanical and

electrical installation/repair/maintenance work.

Organization of chapters

The manual is organized in the following chapters:

ContentsChapter

Safety information that must be read through before performing

any installation or service work on the robot. Contains general

safety aspects as well as more specific information on how to

avoid personal injuries and damage to the product.

Safety

Required information about lifting and installation of the robot.Installation and commis-

sioning

Step-by-step procedures that describe how to perform mainten-

ance of the robot. Based on a maintenance schedule that may

be used to plan periodical maintenance.

Maintenance

Step-by-step procedures that describe how to perform repair

activities of the robot. Based on available spare parts.

Repair

Procedures that do not require specific calibration equipment.

General information about calibration.

Calibration information

Environmental information about the robot and its components.Decommissioning

Continues on next page

Product manual - IRB 2600 9

3HAC035504-001 Revision: G

Overview of this manual

ContentsChapter

Useful information when performing installation, maintenance

or repair work. Includes lists of necessary tools, additional doc-

uments, safety standards etc.

Reference information

Complete spare part list and complete list of robot components,

shown in exploded views.

Spare part / part list

Detailed illustrations of the robot with reference numbers to the

part list.

Exploded views

Reference to the circuit diagram for the robot.Circuit diagram

References

Document IdReference

3HAC035959-

001

Product specification - IRB 2600

3HAC029570-

007

Circuit diagram - IRB 2600

3HAC049106-

001

Product manual, spare parts - IRB 2600

3HAC031045-

001

Operating manual - General safety information

3HAC021313-

001

Product manual - IRC5

IRC5 with main computer DSQC 639.

3HAC047136-

001

Product manual - IRC5

IRC5 with main computer DSQC1000.

3HAC027098-

001

Operating manual - Emergency safety informa-

tion

3HAC050941-

001

Operating manual - IRC5 with FlexPendant

3HAC020738-

001

Operating manual - Trouble shooting IRC5

3HAC16578-

Operating manual - Calibration Pendulum

3HAC050944-

001

Operating manual - Service Information System

3HAC042927-

001

Technical reference manual - Lubrication in

gearboxes

3HAC050948-

001

Technical reference manual - System parameters

3HAC051016-

001

Application manual - Additional axes and stand

alone controller

3HAC050996-

001

Application manual - Electronic Position Switches

3HAC030421-

001

Application manual - CalibWare Field 5.0

iThis manual contains all safety instructions from the product manuals for the manipulators and the

controllers.

Continues on next page

10 Product manual - IRB 2600

3HAC035504-001 Revision: G

Overview of this manual

Continued

Autres manuels pour IRB 2600 Series

Table des matières

Autres manuels ABB Robotique

ABB

ABB IRBP A Instructions d'utilisation

ABB

ABB IRB 120 Manuel du propriétaire

ABB

ABB IRB 910INV Manuel utilisateur

ABB

ABB IRB 930 Manuel utilisateur

ABB

ABB IRB 8700 Manuel utilisateur

ABB

ABB IRB 365 Manuel utilisateur

ABB

ABB IRB 2600 Series Manuel utilisateur

ABB

ABB 180 Comfort Manuel utilisateur

ABB

ABB IRB 640 Manuel utilisateur

ABB

ABB IRB 6660 - 130/3.1 Manuel utilisateur

ABB

ABB IRC5 Compact Manuel utilisateur

ABB

ABB PickMaster Twin - PowerPac Instructions d'utilisation

ABB

ABB IRB 760 Series Manuel utilisateur

ABB

ABB IRB 1200 Manuel du propriétaire

ABB

ABB IRC5 Compact Manuel utilisateur

ABB

ABB CRB 1100 Manuel utilisateur

ABB

ABB CRB 15000 Manuel utilisateur

ABB

ABB IRB 6620LX Manuel utilisateur

ABB

ABB IRB6400 Manuel de programmation

ABB

ABB SpotPack IRB 6620 Manuel utilisateur

ABB

ABB OmniCore V400XT Manuel utilisateur

ABB

ABB IRC5 Compact Guide de l'utilisateur

ABB

ABB Scalable I/O Instructions d'utilisation

ABB

ABB IRB 4400/60 Manuel utilisateur

Manuels Robotique populaires d'autres marques

STEMCenter USA

STEMCenter USA Pi-Bot v2.00 Manuel utilisateur

SunFounder

SunFounder PiDog Manuel utilisateur

Universal Robots

Universal Robots UR5 Manuel utilisateur

Universal Robots

Universal Robots E Series Manuel utilisateur

YASKAWA

YASKAWA MOTOMAN-MPL80 II Manuel utilisateur

EFORT

EFORT ECR5 Manuel d'instructions

Epson

Epson C8 Series Manuel utilisateur

WowWee

WowWee ROBOQUAD Manuel utilisateur

Milvus Robotics

Milvus Robotics SEIT 100 Manuel utilisateur

RoboMaster

RoboMaster AI Robot 2020 Standard Version Manuel utilisateur

fischertechnik

fischertechnik Mini Bots Manuel utilisateur

YASKAWA

YASKAWA MA2010 Manuel

Abicor Binzel

Abicor Binzel iCAT mini Manuel utilisateur

YASKAWA

YASKAWA Motoman DX200 Manuel utilisateur

pitsco

pitsco Tetrix Max Manuel utilisateur

ECOVACS

ECOVACS DEEBOT R95 Manuel utilisateur

Feng Yuan

Feng Yuan Interstellar Warrior Manuel utilisateur

SCHUNK

SCHUNK AGE-S-XYZ Instructions d'utilisation