ABB SM500F Manuel utilisateur

—

ABB MEASUREMENT & ANALYTICS | INSTRUCTION | IN/RANDC/004-EN REV. A

SM500F

Field mountable paperless recorder

Color processor board replacement

This instruction is applicable only

to instruments manufactured after

October 2016

Measurement made easy

1 Introduction

This publication details replacing an SM500F

paperless recorder’s color processor board. The

procedure must be carried out by a trained

technician. The contents of the replacement kit are

shown in Table 1.

Description Part number Qty

Processor board assembly SM500/0215 1

Battery B12454 1

Screw B12406 6

Windows licence B12423 1

This publication IN/RandC/004-EN 1

Table 1 Color processor board assembly replacement

kit SM500/0736

Tools required

• No. 2 Pozidriv screwdriver

• T8 Torx driver

2 For more information

Further information is available from:

www.abb.com/recorders

or by scanning these codes:

Sales Service

SM500F

field mountable

paperless recorder

2 IN/RandC/004-EN Rev. A | SM500F | Field mountable paperless recorder

3 Processor board replacement

1. Disconnect the recorder from the power supply.

2. Referring to Fig. 3.1, unlock the door with the key A,

press release catch Band open the door.

3. Referring to Fig. 3.2, remove 6 Torx screws Csecuring

the door assembly rear cover and remove the rear cover.

Referring to Fig. 3.3:

4. Disconnect processor board flexi-cable D, display

flexi-cable Eand keypad membrane cable Ffrom the

processor board and lift out and discard the processor

board.

5. Position the new processor board in the door housing and

reconnect keypad membrane cable F, display flexi-cable

Eand processor board flexi-cable D.

6. Referring to Fig. 3.2, refit the door assembly rear cover and

secure using 6 Torx screws C.

7. Close and lock the door.

8. Restore the recorder's power supply.

NOTICE – Property damage

The recorder is vulnerable to electrostatic damage.

Wear an anti-static strap or place the instrument on

an anti-static workbench.

Fig. 3.1 Opening the door

Fig. 3.2 Removing the rear cover

Fig. 3.3 Disconnecting the processor board

SM500F | Field mountable paperless recorder | IN/RandC/004-EN Rev. A 3

4 Entering the recorder's serial number

1. Locate the serial number label on the outside of the

recorder and note the serial number.

2. Access the configuration level as described in Section 6 of

the User Guide (IM/SM500F).

3. Access the 'Common' configuration level and select the

Setup tab. Use the and keys to select the 'Options

enabled' parameter and press .

4. Select any option from the list box and press .

5. Use the and keys to select the button next to

the 'Serial number' field. Press the key and using the

displayed keypad, enter the recorder's serial number noted

at step 1.

6. Repeat steps 4 and 5 to enter software option security

codes in the security code field for each option as required.

7. Exit the configuration level as described in Section 6 of the

User Guide (IM/SM500F), saving the configuration as the

'Current Configuration'.

8. Reset archiving as described in Section 5.2 of the User

Guide (IM/SM500F).

IMPORTANT (NOTE) The format of the serial

number is either */*****/*/* or 3K21**********.

IN/RandC/004-EN Rev. A 12.2018

—

We reserve the right to make technical changes or modify the contents of this document

without prior notice. With regard to purchase orders, the agreed particulars shall prevail.

ABB does not accept any responsibility whatsoever for potential errors or possible lack of

information in this document.

We reserve all rights in this document and in the subject matter and illustrations contained

therein. Any reproduction, disclosure to third parties or utilization of its contents – in

whole or in parts – is forbidden without prior written consent of ABB.

—

ABB Limited

Measurement & Analytics

Howard Road, St. Neots

Cambridgeshire, PE19 8EU

Tel: +44 (0)0870 600 6122

Fax: +44 (0)1480 213 339

Email: instrumen[email protected]om

ABB Inc.

Measurement & Analytics

125 E. County Line Road

Warminster

PA 18974

USA

Tel: +1 215 674 6000

Fax: +1 215 674 7183

abb.com/measurement

Autres manuels pour SM500F

Autres manuels ABB Instrument de mesure

ABB

ABB FSM4000-SE41F Manuel utilisateur

ABB

ABB SM3000 Manuel utilisateur

ABB

ABB PFCL 201 Manuel utilisateur

ABB

ABB TOTALFLOW X G4 Series Guide de l'utilisateur

ABB

ABB RELION 650 SERIES Manuel utilisateur

ABB

ABB Relion RES670 Manuel utilisateur

ABB

ABB FXE4000 Manuel de formation

ABB

ABB 8241 Manuel utilisateur

ABB

ABB MagMaster MF/F Guide de démarrage rapide

ABB

ABB M4M 20 Manuel utilisateur

ABB

ABB M1M 30 Series Manuel utilisateur

ABB

ABB ScreenMaster RVG200 Manuel utilisateur

ABB

ABB CM-UFD.M21 Supplément

ABB

ABB FMT200-ECO2 Manuel utilisateur

ABB

ABB EL3000 Series Manuel utilisateur

ABB

ABB TMD-T4 Manuel utilisateur

ABB

ABB FV4000 Manuel utilisateur

ABB

ABB 2410 Manuel utilisateur

ABB

ABB FAM3200 Series Manuel d'installation et d'exploitation

ABB

ABB ProcessMaster FEP630 series Manuel utilisateur

ABB

ABB CoreSense M10 Manuel utilisateur

ABB

ABB TTF200 Manuel utilisateur

ABB

ABB PointMaster 200 Series Manuel utilisateur

ABB

ABB C11 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur