ABB ScreenMaster RVG200 Manuel d'utilisation original

Service instruction SI/RandC/001-EN

ScreenMaster RVG200

Paperless recorder

Terminal block failures

Measurement made easy

1Introduction

There have been instances reported where some or all inputs

on an RVG200 analog input card have shown as failed

immediately after installation, with no apparent cause for the

failure. In rare cases, this can be attributed to a faulty analog

input card but the most common cause has been identified as

a problem affecting the connection strips within the terminal

block assembly.

The reason for potential failure is that during installation,

unscrewing the terminal connection, inserting the wire and

tightening the screw can cause the spring assembly inside the

terminal block to move, breaking its contact with the PCB.

2Action

3 Tools required

— Medium, flat-bladed screwdriver

4 Identifying failures

1. Isolate the recorder from the power supply.

Referring to Fig. 4.1 (overleaf),

2. Press down into recess Aand pull terminal cover B

away from the case.

Continued...

Action when fault reported Action at next service

Information only Recall instruments

WARNING – Bodily injury

Isolate all power supplies to the recorder before removing

the terminal cover.

NOTICE – Property damage

The recorder is vulnerable to electrostatic damage.

Wear an anti-static strap or dismantle the unit on an

anti-static workbench.

SI/RandC/001-EN 10.2015

3. Insert a flat-bladed screwdriver into each slot Cin turn (2

slots) to release the locking arm and pull terminal block D

away from the case.

4. Check the position of spring contacts Ewithin the

terminal block assembly.

The correct position for the contacts is as shown in Fig. 4.1

– each contact must be positioned a minimum of halfway

across the slot in which the module board fits.

5. If a contact is positioned incorrectly or is damaged, replace

the terminal block assembly.

6. Fit the terminal block.

7. Refit terminal cover B.

Fig. 4.1 Examining the terminal block contacts

Note

We reserve the right to make technical changes or modify the contents of this

document without prior notice. With regard to purchase orders, the agreed

particulars shall prevail. ABB does not accept any responsibility whatsoever for

potential errors or possible lack of information in this document.

We reserve all rights in this document and in the subject matter and illustrations

contained therein. Any reproduction, disclosure to third parties or utilization of its

contents in whole or in parts – is forbidden without prior written consent of ABB.

ABB Limited

Process Automation

Howard Road

St. Neots

Cambridgeshire PE19 8EU

Tel: +44 (0)1480 475321

Fax: +44 (0)1480 217948

ABB Inc.

Process Automation

125 E. County Line Road

Warminster

PA 18974

USA

Tel: +1 215 674 6000

Fax: +1 215 674 7183

www.abb.com

Autres manuels pour ScreenMaster RVG200

Autres manuels ABB Instrument de mesure

ABB

ABB 2410 Manuel utilisateur

ABB

ABB FAM3200 Series Manuel d'installation et d'exploitation

ABB

ABB JDF300 Manuel utilisateur

ABB

ABB Sensyflow FMT200-D Manuel utilisateur

ABB

ABB Aztec 600 Color Manuel utilisateur

ABB

ABB EL3000 Series Manuel utilisateur

ABB

ABB AW101 Manuel utilisateur

ABB

ABB Relion 630 Series Fiche technique

ABB

ABB ISL-C 600 Manuel utilisateur

ABB

ABB MagMaster MF/F Guide de démarrage rapide

ABB

ABB RES670 2.1 Guide de démarrage rapide

ABB

ABB Relion 670 series Instructions d'utilisation

ABB

ABB M4M 30 Manuel utilisateur

ABB

ABB ProcessMaster FEM630 Manuel utilisateur

ABB

ABB SM1000 Manuel utilisateur

ABB

ABB Navigator 600 Silica Manuel utilisateur

ABB

ABB Endura AZ20 series Manuel utilisateur

ABB

ABB Sensyflow FMT400-VTS Manuel utilisateur

ABB

ABB Endura AZ20 series Manuel utilisateur

ABB

ABB Relion 670 series Guide de démarrage rapide

ABB

ABB GLA131 Series Manuel utilisateur

ABB

ABB AK101 Manuel utilisateur

ABB

ABB MagMaster Feuille d'instructions

ABB

ABB NETA-21 Manuel d'installation

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur