ABB ISL-C 600 Manuel utilisateur

2024-01-24 1/7

—

INSTRUCTION MANUAL

ISL-C 600

INSULATION MONITORING DEVICE FOR ISOLTAED IT (AC) NETWORKS

—

GENERAL

In IT electrical distribution networks with isolated neutral, the high insulation impedance prevents earth faults

from generating currents that would dangerously elevate the potential of exposed conductive parts.

Therefore, in case of earth leakage in an IT network it is not necessary to interrupt the supply, but it is still es-

sential to continually monitor the insulation level in order to detect faults and restore optimal functioning of

the system.

The ISL-C 600 is an Insulation Monitoring Device for IT networks with voltages up to 760 Vac.

By putting a continuous component measure signal between the insulated line and earth, it’s possible to con-

trol the insulation resistance by reading the dispersion current generated to earth.

These devices have two trip thresholds (ALARM and TRIP) adjustable using the front micro-switches to signal

when the insulation falls below the threshold level.

The front LED signals the trip.

Two free voltage changeover contact relays allow the remote trip signalling. The relays can be programmed

with the fail-safe (normally excited). The device is equipped on the front panel with a TEST and a RESET push-

button.

The test can be activated either by the push-button on the device or an external push-button, while the reset,

that can be set to manual or automatic, is activated, as is the test, with the local or remote push-button.

The level of the insulation resistance is displayed on the bar LED on the front panel with a scale of 5-500 kΩ at

8 points.

—

MODEL

ISL-C600 network voltage and auxiliary supply 110-230V 50-60 Hz (100÷130 / 220÷240V ± 10%)

2024-01-24 2/7

—

OPTIONS

Voltage of work different from standard (on request).

—

INSTALLATION

The installation must be carried out by qualified and authorized personnel and in absence of voltage.

Make sure that the instrument is O.K. and it has not suffered any damage during transport.

Make sure that the voltage supply is compatible with the operating voltage of the instrument.

The device is a 6 modules (17.5mm) DIN version with snap on 35mm DIN rail.

It has a sealable transparent front protection cover.

The green LED ON will light up after the connections are set and the instrument is powered on.

DESCRIPTION

1. RESET push-button. Only when it's set to manual reset functioning, this push-button is enabled.

2. TEST push-button. Pressing the TEST push-button causes the tripping of the ALARM and the TRIP,

and the output relay to switch.

3. LED ON to signal the device is turned ON.

4. LED TRIP for the signal indicating overcoming the TRIP threshold.

5. LED ALARM for the signal indicating overcoming the ALARM threshold.

6. LED bar to indicate the measured insulation resistance level. With all LEDs on, the insulation level

is lower than 5 kΩ; with all LEDs off, the insulation level is higher than 500 kΩ.

7. Terminals board

8. Micro-switches to set the alarm threshold.

9. Micro-switches to set the trip threshold.

2024-01-24 3/7

—

MICRO-SWITCHES SETTING

The front micro-switches allow the setting of the insulation level tripping thresholds, the insertion of the

fail-safe function and the reset mode for the alarm and trip thresholds.

Micro- switches A,B,C,D to set the tripping thresholds:

ALLARM TRIP

300 kΩ : A=0, B=0, C=0, D=0 100 kΩ : A=0, B=0, C=0, D=0

150 kΩ : A=1, B=0, C=0, D=0 60 kΩ : A=1, B=0, C=0, D=0

80 kΩ: A=1, B=1, C=0, D=0 40 kΩ : A=1, B=1, C=0, D=0

50 kΩ: A=1, B=1, C=1, D=0 20 kΩ: A=1, B=1, C=1, D=0

30 kΩ: A=1, B=1, C=1, D=1 10 kΩ: A=1, B=1, C=1, D=1

Micro-switch E to set the FAIL SAFE mode

E=0 Fail safe function disabled

E=1 Fail safe function enabled

Micro-switch F to set the RESET mode

F=0 Manual reset

F=1 Automatic reset

2024-01-24 4/7

—

WIRING CONNECTION

2024-01-24 5/7

—

LEGEND

Auxiliary power supply

Terminals 1-2-3-4

The supply section is a double input at 115V (100÷130V 50-60Hz). To supply the instrument at 230V (220÷240V

50-60Hz) connect the two sections in series. To supply the instrument at 115V connect the two sections in

parallel.

Insulation control

Terminals (6/7) -22

The two terminals must be connected between the line under control and the earth of measure reference.

The double terminal 6/7 (connected internal) must be connected to the earth reference while the terminal 22

must be connected to the single-phase line to control or to the neutral conductor in a three-phase line. In a

three wire three phase network, the terminal 22 must be connected to one phase.

With these terminals, it is possible to connect voltage up to 760Vac. For this reason, it’s possible to use this

device on a single-phase line up to 760V, on a three-phase line with 3 wires without neutral up to 760V, and on

a three-phase line with 4 wires with neutral up to 1100V.

Alarm relay output connections (ALARM)

Terminals 16-17-18

Connections for remote signalling are made through a free voltage changeover contact, max 5A 250V on resis-

tive load.

Trip relay output connections (TRIP)

Terminals 12-13-14

Connections for remote signalling are made through a free voltage changeover contact, max 5A 250V on resis-

tive load.

Remote TEST connection

Terminal 8

It’s possible to connect a remote push-button with a normally open contact between the control device and

the earth reference.

Remote RESET connection

Terminal 9

For the RESET function from an external signal, a push-button with a normally open contact can be connected

between the control device and the earth reference.

2024-01-24 6/7

—

FUNCTIONALITY

In normal conditions, when the insulation value is higher than the alarm and trip thresholds, the device's green

LED turns on, along with the LED bar which displays the measured insulation resistance level (all LEDs off indi-

cates an insulation value higher than 500 kΩ, while all LEDs on indicate a value lower than 5 kΩ).

By pressing the TEST push-button for at least 5 seconds (delay time), the alarm and trip signals along with

their respective LEDs will be activated, the output relays will engage, and the LED bar will turn on (indicating a

simulated value lower than 5 kΩ).

Depending on the micro-switches setting, the RESET function can be automatic when the TEST push-button

is released, or it can be manually activated using the local or remote RESET push-button.

In the case of low insulation on the line (insulation resistance value lower than the set threshold), the ALARM

and possibly the TRIP signals will be activated, as well as the corresponding output relays.

The signals will only disappear after the insulation level rises above the set threshold again.

—

NOTE

It’s not possible to use more than one instrument on a line because the measure of the resistance could

be not correct for the overlap of the signal. The presence of strong continuous component on the network

under control could create some problems for the correct functioning of the device.

DIMENSIONS

2024-01-24 7/7

—

TECNICAL FEATURES

Auxiliary power supply

110-230Vac (100÷130V / 220÷240V +-10%) 50-60Hz

Maximum consumption

max 5 VA

Network to control

50-760Vac (1100V on three-phase line with neutral)

Measure voltage

max 48Vdc

Measure current

max 240 μA dc

Internal impedance

200 kΩ

Tripping delay

max 5 seconds

Signalling

led ON, led ALARM, led TRIP, measuring LED bar 5-500 kΩ

Setting threshold tripping ALARM

300 ÷ 30 kΩ (5 levels settings via micro-switches)

Setting threshold tripping TRIP

100 ÷ 10 kΩ (5 levels settings via micro-switches)

Relay output

ALARM: changeover contact NA-C-NC

TRIP: changeover contact NA-C-NC

Relay contacts

5 A 250Vac .

Functions

Fail safe function for both outputs, manual or automatic reset,

local and remote test and reset push-button

Working temperature

-10 ÷ 60°C

Storing temperature

-20 ÷ 70°C

Relative humidity

≤ 95 %

Insulation test

3 kV 60 sec. / 4 kV imp. 1,2/50μs

Mounting position

Any

Wiring type

By screw terminals –wire section max 2.5 mm²

Protection degree

IP 40 front cover - IP 20 case

Mounting according DIN 50022

Connection snap on DIN rail 35mm / 6 modules of 17,5 mm

Weight

0,5 kg

Standards

Safety IEC-EN 61010-1 / Product IEC-EN 61557-8 / Electromag-

netic compatibility IEC-EN 61326-1 EN 61326-2-4

For application not described in this manual it’s better to see specific document or to contact the technical

service.

—

NOTE

At reason of the evolution of standards and products, the company reserves to modify in every time the features of the product described

in this document, that it’s necessary to verify preventively. The liability of the producer for damage caused by defect of the product ”can

be reduced or deleted (…) when the damage is caused joint by a defect of product or for blame of the damaged or a person of which the

damaged is responsible” (Article 8, 85/374/CEE).

Table des matières

Autres manuels ABB Instrument de mesure

ABB

ABB MagMaster Manuel utilisateur

ABB

ABB ICOS GLA151 Series Manuel utilisateur

ABB

ABB ReliaGear ASPMETER A 42 Manuel d'installation et d'exploitation

ABB

ABB CoriolisMaster FCM2000 Instructions d'installation

ABB

ABB Sensyflow FMT700-P Manuel utilisateur

ABB

ABB 10D1475 Manuel utilisateur

ABB

ABB DATUM L150 Manuel utilisateur

ABB

ABB EL3060 Series Guide de l'utilisateur

ABB

ABB Navigator 600 Phosphate Manuel utilisateur

ABB

ABB SM1000 Manuel utilisateur

ABB

ABB Relion 670 series Manuel utilisateur

ABB

ABB NGC8206 Manuel utilisateur

ABB

ABB MagMaster MF/F Guide de démarrage rapide

ABB

ABB ACX Manuel d'installation et d'exploitation

ABB

ABB ControlMaster CM15 Manuel utilisateur

ABB

ABB ScreenMaster RVG200 Manuel d'utilisation et d'entretien

ABB

ABB CoriolisMaster FCB330 Manuel d'installation et d'exploitation

ABB

ABB 10D1475 Manuel utilisateur

ABB

ABB Sensyflow FMT200-D Manuel utilisateur

ABB

ABB K-TEK AccuTrak AT500 Manuel utilisateur

ABB

ABB SensyMaster FMT230 Manuel d'installation et d'exploitation

ABB

ABB AV1 Manuel utilisateur

ABB

ABB COMMANDER 1911 Manuel utilisateur

ABB

ABB B21 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur