ABB Cassia X1000 Manuel utilisateur

DOCUMENT ID

REV.

DATE

LANG.

PAGE

9AKK107046A4620

August 2022

1/29

—

ABB MOTION SERVICES

ABB Ability™ Smart Sensor Bluetooth®

Gateway

Cassia X1000 installation manual

ABB ABILIT Y™ SMART SENSOR BLUETOOTH ® GATEWAY

DOCUMENT ID

REV.

DATE

LANG.

PAGE

9AKK107046A4620

August 2022

2/29

Table of contents

1GENERAL....................................................................................................... 3

2INSTALLATION.............................................................................................. 4

2.1 Prerequisites for installation ........................................................................................4

2.2 Recommended location .................................................................................................6

2.3 Gateway configuration ..................................................................................................7

2.3.1 Network configuration – Firmware 1.4.3 .................................................................... 10

2.3.2 Network configuration – Firmware 2.1.0 .....................................................................11

2.4 PoE connection .............................................................................................................15

2.5 LAN/Ethernet cable connection .................................................................................16

2.6 WIFI connection ............................................................................................................ 17

2.7 USB mobile dongle connection ...................................................................................18

2.8 Firewall configuration..................................................................................................20

2.9 Verifying the configuration......................................................................................... 21

2.10 Commissioning the gateway ...................................................................................23

3TROUBLESHOOTING ................................................................................. 25

ABB ABILIT Y™ SMART SENSOR BLUETOOTH ® GATEWAY

DOCUMENT ID

REV.

DATE

LANG.

PAGE

9AKK107046A4620

August 2022

3/29

1General

The ABB Ability™ Smart Sensor gateway is used to upload the Smart Sensor data

automatically to the Smart Sensor portal. The gateway needs to be configured for Internet

access before it can start reading the Smart Sensors. Following Internet connections are

supported:

-LAN/Ethernet network together with PoE injector.

-2.4GHz WIFI network.

-3G/4G Mobile network with specific USB dongle.

The sales package includes:

-X1000 Bluetooth router, wall and pole mounting kits and a quick guide.

Figure 1 Content of the sales package

For general information about the Cassia gateway, please refer to the Cassia User Manual on

https://www.cassianetworks.com/download/docs/Cassia_User_Manual.pdf

ABB ABILIT Y™ SMART SENSOR BLUETOOTH ® GATEWAY

DOCUMENT ID

REV.

DATE

LANG.

PAGE

9AKK107046A4620

August 2022

4/29

2Installation

2.1 Prerequisites for installation

Internet connection:

-Gateway does not operate in networks with a VPN (Virtual Private Network).

-The default DNS server address is the Google DNS server for Global customers

(8.8.8.8) and the Baidu DNS server for customers located in China (114.114.114.114).

-In case there is a firewall used, the following ports need to be open for outbound

communication:

Type

Port

M/O

Communication

Partner for

Gateway

Description

UDP

5246,

5247

* Mandatory

Access Controller (AC)

Default CAPWAP communication between

AC and router. Mandatory for FW 1.4.3

* Optional for FW 2.1.0

UDP

6246,

6247

Optional

Access Controller (AC)

Backup CAPWAP communication between

AC and router.

TCP

8883

Mandatory

Access Controller (AC)

MQTT communication between AC and

router.

TCP

1883

Optional

Local MQTT broker

MQTT bypass function.

TCP/HTTP

Optional

Access Controller (AC)

Container/APP download from AC.

TCP/HTTPS

443

Mandatory

Access Controller (AC)

Smart Sensor

Platform

Container/APP download from AC

Communication with Smart Sensor

Platform

TCP

9999

Mandatory

Access Controller (AC)

Remote SSH to container

UDP

Mandatory

DNS server

DNS lookup for AC address

AC – Access Controller

Global: gw.smartsensor.abb.com

China: gw.smartsensor.abb.com.cn

Smart Sensor Platform

Global: smartsensor.abb.com

China: smartsensor.abb.com.cn

-Only one AC address must be whitelisted in the network. For the gateways working

outside China, the Global AC address must be whitelisted. For gateways working

inside China, only the China AC address must be whitelisted.

-Smart Sensor Platform and all the existing subdomains must be whitelisted in the

network for a successful communication and measurement report to the Portal.

ABB ABILIT Y™ SMART SENSOR BLUETOOTH ® GATEWAY

DOCUMENT ID

REV.

DATE

LANG.

PAGE

9AKK107046A4620

August 2022

5/29

-Mobile network needs to have adequate signal strength. In the most demanding

locations, an extension USB cable or external antenna might be needed for the USB

modem/dongle.

Power supply:

-In case PoE network is not available, a PoE injector (power supply) is needed.

-PoE is 802.3af/at compliant.

-Recommended PoEs:

oProcet PT-PSE104GO-30-5, Indoor PoE Injector

oProcet PT-PSE108GBR-OT, Outdoor PoE Injector

Ethernet cable:

-1 CAT6 shielded Ethernet cable (RJ45), with a length of 50 meters maximum, is

needed for PoE, while WIFI or mobile network is used.

-2 CAT6 shielded Ethernet cables (RJ45), with a length of 50 meters maximum, are

needed when LAN/Ethernet network is used.

Computer:

-A computer with WIFI adapter is needed for gateway configuration. A tablet

computer or mobile phone can also be used.

-Google Chrome web browser is recommended to be used.

USB Cellular Modem / Dongle

-The gateway has built in drivers for several USB dongles. For the list of supported

dongles please check the section 2.7 USB mobile dongle connection.

-A SIM card with Internet data plan.

-The gateway also supports the use of any USB powered WIFI modems.

Mounting:

-Flat head screwdriver for pole mounting.

-Phillips head screwdriver and a drill (if needed) for wall mounting.

-Mounting is not mandatory, but it is recommended to secure the gateway

somehow to its intended place.

ABB ABILIT Y™ SMART SENSOR BLUETOOTH ® GATEWAY

DOCUMENT ID

REV.

DATE

LANG.

PAGE

9AKK107046A4620

August 2022

6/29

2.2 Recommended location

Height:

-The recommended height for the gateway is 3-30 meters from ground level. Lower

levels are also acceptable, but the gateway Bluetooth range might be shorter due

to obstacles.

Orientation:

-The gateway has the best reception in the direction where the Cassia logo is

shown on its side. If the gateway has trouble connecting to a specific Smart

Sensor, it is recommended to rotate the gateway to point in that direction.

ABB ABILIT Y™ SMART SENSOR BLUETOOTH ® GATEWAY

DOCUMENT ID

REV.

DATE

LANG.

PAGE

9AKK107046A4620

August 2022

7/29

2.3 Gateway configuration

When the gateway is powered on, the blue LED at the bottom of the gateway turns ON.

After bootup, the gateway will turn on the configuration WIFI hotspot. The bootup takes

about 30-60 seconds.

Configuration WIFI hotspot has SSID “cassia-XXXXXX”, where XXXXXX are the last 6

characters of the gateway’s MAC address. MAC address can be found on the bottom of

the gateway. Password for this WIFI hotspot is the same as the SSID.

Connect to this WIFI hotspot with the device used for configuration (computer, phone or

tablet) and open the web browser. Type 192.168.40.1 to the web browser’s address field

and press enter. Cassia configuration page will open. During the first login the default

password needs to be changed. Default credentials are:

-Login: admin

-Password: admin

Figure 2 Cassia (Firmware 1.4.3) Login

Figure 3 Cassia (Firmware 2.1.0) Login

ABB ABILIT Y™ SMART SENSOR BLUETOOTH ® GATEWAY

DOCUMENT ID

REV.

DATE

LANG.

PAGE

9AKK107046A4620

August 2022

8/29

Once logged in, the Status Page is shown. This page shows current operation mode and

connection status of the gateway. AC Online Time shows how long the gateway has been

connected to the AC (Access Controller) server. If no time is shown, it means that the

gateway does not have a connection to the AC server.

Access Controller server connection is needed for a successful Smart Sensor data

transfer.

As the gateway now supports two firmware versions, the UI is different between the old

firmware (1.4.3) and the new firmware (2.1.0), the latter having more information about

the current state of the gateway.

Figure 4 Cassia (Firmware 1.4.3) Status

ABB ABILIT Y™ SMART SENSOR BLUETOOTH ® GATEWAY

DOCUMENT ID

REV.

DATE

LANG.

PAGE

9AKK107046A4620

August 2022

9/29

Figure 5 Cassia (Firmware 2.1.0) Status

ABB ABILIT Y™ SMART SENSOR BLUETOOTH ® GATEWAY

DOCUMENT ID

REV.

DATE

LANG.

PAGE

9AKK107046A4620

August 2022

10/29

2.3.1 Network configuration – Firmware 1.4.3

The Basic Page is where the configuration is done.

Following values are common for all network configurations (LAN, WIFI, Mobile):

-Router Mode: AC Managed Router

-Tx Power: 20

-Statistics Report Interval: 5 minutes

-AC Server Address: gw.smartsensor.abb.com

-AC Server Address for China: gw.smartsensor.abb.com.cn

-AC Router Comm. Ports: 5246, 5247

-Remote Assistance: ON

Connection Priority is where a priority connection method is selected in case there are

several in use. Select the priority according to connection in use:

-Wired for PoE and LAN connections.

-Wireless for WIFI connection.

-3G/4G for mobile USB dongle connection.

If all the information has been filled as shown above and the Wired, Wireless or 3G/4G

sections are configured according to your network specifications, please refer to 2.9

Verifying the configuration to check if the connection has been successfully set-up.

Autres manuels pour Cassia X1000

Table des matières

Autres manuels ABB Porte

ABB

ABB 83330-5 Series Manuel utilisateur

ABB

ABB Terra Gateway Pro Manuel utilisateur

ABB

ABB Ekip E-Hub Manuel utilisateur

ABB

ABB COM600 series Feuille d'instructions

ABB

ABB ARM600 Manuel utilisateur

ABB

ABB Cassia DODGE Manuel utilisateur

ABB

ABB 3AUA0000235813 Manuel utilisateur

ABB

ABB i-bus KNX SUG/U 1.1 Manuel utilisateur

ABB

ABB i-bus KNX MG/S 11.100.1.1 Manuel utilisateur

ABB

ABB 83342-500 Manuel utilisateur

ABB

ABB DG/S 1.1 Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

ABB

ABB ARG600 ANSI Manuel utilisateur

ABB

ABB Ability Manuel utilisateur

ABB

ABB ARG600 Dual SIM Manuel utilisateur

ABB

ABB Busch-Welcome Manuel utilisateur

ABB

ABB AWIN GW120 Manuel utilisateur

ABB

ABB TG/S 3.1 Manuel utilisateur

ABB

ABB Welcome IP H8301 Manuel utilisateur

ABB

ABB ARP600 Manuel utilisateur

ABB

ABB AWIN GW100 Manuel utilisateur

ABB

ABB ARR600 Manuel utilisateur

ABB

ABB i-bus DALI-Gateway DG/S 8.1 Manuel utilisateur

ABB

ABB COM600 series Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur

RTA

RTA 460MCBC-N2E Fiche technique