3M LM1 Manuel utilisateur

Best practice guidance:

Charging your 3M™ Clean-Trace™ LM1 Luminometer

On receipt of your Clean-Trace LM1 luminometer:

Charging your LM1 instrument to a full battery should usually take around 2 hours but on

occasions a longer charge may be required.

Charging your Clean-Trace LM1 luminometer for continued use:

Ensure the luminometer is routinely charged. You can use the battery level indicator to keep

the luminometer charged to a reasonable level

The battery level indicator is in the upper right corner of the screen.

When the luminometer is switched on, the indicator shows the remaining battery level.

In Figure 1, the indicator shows the battery is fully charged.

As the battery charge decreases, the blue segment of the indicator becomes smaller.

When the battery level is less than 10%, the indicator becomes red, showing the battery

should be recharged.

When the battery level is less than 5%, the LM1 luminometer will automatically shut down.

It is advisable to maintain the charge of your luminometer in the ‘blue’ zone of the battery

indicator. Avoid the battery going below 5% charge and switching off.

Switching off your Clean-Trace LM1 luminometer correctly

In order to maintain the battery life of your luminometer, it is advised to switch it off correctly

after use following the process below.

1. Press the on/off button for 3 seconds.

2. [Power off] appears on the screen to confirm the power off process has started.

3. Tap [Power off].

4. A confirmation message the luminometer will shut down appears.

5. Tap [OK]. The display screen goes black to confirm the power off process has completed.

6. Or, tap [Cancel] to cancel the power off process if you wish to continue using the

luminometer.

Sleep Mode

The Clean-Trace LM1 luminometer conserves battery power if the touch screen or the cursor

control buttons are inactive. After 5 minutes of inactivity, the luminometer goes into Sleep

mode and the screen darkens.

After 2 further hours of inactivity, the luminometer automatically shuts down and must be

powered on again before use.

Waking the Clean-Trace LM1 luminometer from Sleep Mode

1. Press and hold the up-arrow button on the cursor control pad for 3 seconds.

2. The screen displays the information that appeared before the Sleep mode began so you can

continue working.

If the luminometer does not wake from the Sleep mode, the luminometer might be turned off.

Press and hold the on/off button for 3 seconds to turn it on.

If the battery is at a low charge before the luminometer goes into Sleep mode, this may result

in the battery becoming completely discharged. This will then result in the luminometer failing

to switch on due to insufficient charge.

In this case, the luminometer will need to be put on charge from the mains charger (not the PC

USB). After 30 minutes of charging you should then be able to switch on the machine

however it will likely require further charge to reach adequate charge for use. To maintain

battery performance, the luminometer should be switched on within 3 hours after placing the

unit on charge.

For further support, please visit www.3M.com/foodsafety/cleantracesupport

Web: www.3M.com/foodsafety Email: emeafoodsaf[email protected]m

3M and Clean-Trace are trademarks of 3M. © 3M 2018

Autres manuels pour LM1

2

Table des matières

Autres manuels 3M Instrument de mesure

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur