2B Technologies UV-106W Manuel utilisateur

BTechnologies, Inc.2

UV-106W-Aqueous Ozone Monitor™

Quick Start Guide

1) Mount the instrument upright. If there is no structure to mount the instrument to, set it on a block

on the bench-top to keep it level and provide access to the ports on the bottom.

2) Attach the electrical inputs and outputs:

a. Power (required): Use the included AC-12V DC power pack and attach it to the barrel

connector on the cable

b. Serial (optional): Attach one end of the included serial cable to the serial connector on

the cable and the other end through the USB to serial converter to a computer. Open the

desired terminal program (we recommend TeraTerm) and select the appropriate COM

port.

i. The settings on this COM port should be: 38400 baud rate, 8-bits, no parity, 1

stop bit.

c. 4-20mA (optional): The purple wire is the positive side of the 4-20mA output and the

white wire is the ground. See manual for setting the range on this output

d. 0-2.5V (optional): The orange wire is the positive side of the 0-2.5V output and the white

wire is the ground. See manual for setting the range on this output.

3) Attach the tubing connections:

a. Drain: Attach tubing from the drain outlet to waste.

b. Sample Inlet: Attach ozone compatible tubing to the sample inlet port. This tubing should

be as short of a length as possible from your main system in order to reduce response

time.

c. Return: If you are returning this to your system, you should use ozone compatible tubing

and make sure it attaches to a point in your system that is lower pressure than where

you attached the sample line. Otherwise, send to waste.

d. Air Inlet: If the instrument is being used in a hose-down environment, attach tubing and

run it to an area that will not be exposed to water. Otherwise leave open.

e. Air exhaust: If the instrument is being used in a hose-down environment, attach tubing

and run it to an area that will not be exposed to water. Otherwise, leave open.

4) Allow for warmup period:

a. Turn the instrument on and allow it to warmup for 10-20 minutes before taking ozone

measurements.

Table des matières

Autres manuels 2B Technologies Instrument de mesure

2B Technologies

2B Technologies Ozone Monitor 106-L Manuel utilisateur

2B Technologies

2B Technologies 211 Manuel utilisateur

2B Technologies

2B Technologies 211 Manuel utilisateur

2B Technologies

2B Technologies 306 Manuel d'installation

2B Technologies

2B Technologies AQSync Manuel utilisateur

2B Technologies

2B Technologies 106-H Manuel utilisateur

2B Technologies

2B Technologies 405 nm Manuel utilisateur

2B Technologies

2B Technologies OEM-106-H Manuel utilisateur

2B Technologies

2B Technologies POM Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur