2B Technologies 211 Manuel utilisateur

2BTechnologies, Inc.

An InDevR Company

Technical Note No. 037

Procedure for Programming Model 211 Ozone Monitor and Model 405 nm

NO2/NO/NOxMonitor

Date: 29 April 2014

Author: Craig Williford

Requirements

Programming the Model 405 and 211 monitors requires a computer running the "Analog

Devices Serial Downloader" program to download the firmware from the computer to the

monitor, and the straight through rs232 serial cable provided by 2B Technologies. The

computer must have a serial port or a USB port with a USB to Serial converter cable to

connect to the rs232 serial cable provided by 2B Technologies.

Procedure

I. Install Windows Serial Downloader Application

1. If not already installed, please install the WSD.exe application provided by 2B

Technologies.

2. In the “Configuration” menu on the WSD, set the Port number to the COM port

that corresponds to the one your serial connector is connected to. Normally

this is COM1 unless you do not have a serial port on your computer and you are

using a serial to USB converter. If using the serial to USB converter, check in

Windows Device Manager for the correct port number corresponding to the

converter.

II. Record all stored parameters

1. Enter the main menu and write down or record calibration parameters (CF, SF,

NO2 and NO slope, NO2 and NO zero), averaging frequency. This is

imperative as you will need to re-enter these parameters after programming the

new firmware.

III. Removal of top cover

1. Remove the six screws on the tops of the sides securing the top cover on.

2. Remove the unscrewed lid.

IV. Programming instrument

1. Plug in 12V power source for instrument.

2. Connect RS232 cable to D9 connector on back of instrument and other end to

PC.

3. Open a serial emulator such as the 2B Data Display Software, Teraterm, or

Hyperterminal on available com port running at 9600 Bits per second, 8 data

bits, No parity, 1 stop bit, hardware flow control.

4. Locate “sw2” on circuit board. It is a small push button switch located above

the pressure sensor.

5. Press and hold the button labeled "sw2" on the PCB.

6. Power on the instrument.

7. Look on the serial emulator window for data output starting with "ADuC834".

(If data not seen on theterminal, repeat steps 5-7 until you see the data output.)

8. The instrument is now ready to have a new program downloaded to it from the

PC through the RS232 cable.

9. Close the terminal screen which will release the COM port.

10.Open the WSD (Windows Serial Downloader)

11.Press the "Reset" button on the WSD screen.

12.When the board is Reset properly the WSD screen will output this:

Configuration: COM1, 9600 baud, RESETTING PART: OK

13.Press the "Download" button on the WSD screen.

14.Choose the .hex file to download (For example: NO405VER23K.hex)

15.You will see a bar on the WSD screen showing the progress of the download.

When the bar has completed the download is successful.

16.Cycle Power to be sure the new version starts correctly.

V. Replace top cover and re-enter menu parameters

1. Replace top cover in the reverse process as removal.

2. Re-enter all parameters recorded in step 1 of section II.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels 2B Technologies Instrument de mesure

2B Technologies

2B Technologies OEM-106-H Manuel utilisateur

2B Technologies

2B Technologies 306 Manuel d'installation

2B Technologies

2B Technologies 405 nm Manuel utilisateur

2B Technologies

2B Technologies 106-H Manuel utilisateur

2B Technologies

2B Technologies 211 Manuel utilisateur

2B Technologies

2B Technologies AQSync Manuel utilisateur

2B Technologies

2B Technologies POM Manuel utilisateur

2B Technologies

2B Technologies Ozone Monitor 106-L Manuel utilisateur

2B Technologies

2B Technologies UV-106W Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur