ZOSI C309 Manuel utilisateur
Wire-Free Baery
Camera System
Please read the Quick Start Guide carefully before using the product and keep it properly.
Scan the QR code on the device via ZOSI Cloud App.
Please set a device password and keep it in mind (the original device password is blank):
Password is required for logging in to the device and remote viewing. It is recommended to write
down the password on the QSG for safekeeping.
V6.I.01.Z
Contents
EN 1 - 12
ES 13 - 24
FR 25 - 36
DE 37 - 48
IT 49 - 60
NL 61 - 72
01/What’s in the Box
1.1 Packing List of Base Staon Kit
2-cam：
Camera*2 Baery Pack *1
5V-2A Power Supply of Base Staon*15V -1A USB Charger+Cable*1
Quick Start Guide*1
Mounng Screw Bag*2 Mounng Base*2 Reset Needle*1 Screwdriver*1
1m Network Cable*1
Base Staon*1
4-cam：
Quick Start Guide
Baery Pack *1
5V-2A Power Supply of Base Staon*1
Quick Start Guide*1
Reset Needle*1 Screwdriver*1
1m Network Cable*1
Quick Start Guide
Camera*4
5V -1A USB Charger+Cable*1
Mounng Screw Bag*4Mounng Base*4
Base Staon*1
1
1m Network Cable*1Baery Pack *1
1.2 Packing List of NVR Kit
4-cam：
Camera*4
12V-2A Power
Supply of NVR*1
5V -1A USB
Charger+Cable*1
Quick Start Guide*1
Mounng Screw Bag*4 Mounng Base*4 Reset Needle*1 Screwdriver*1
USB Mouse
NVR*1
8-cam：
Quick Start Guide
1m Network Cable*1
Baery Pack *1
Camera*8
12V-2A Power
Supply of NVR*1
5V -1A USB
Charger+Cable*1
Quick Start Guide*1
Mounng Screw Bag*8Mounng Base*8 Reset Needle*1 Screwdriver*1
USB Mouse
NVR*1
Quick Start Guide
2
2.1 Camera
Camera`s network indicator status:
Blue light and red lights on: The camera is being previewed remotely
Blue light on: The camera is paired or woken up
Blue light flashes connuously: Upgrading
Red light flashes slowly: Waing to pair with base staon
Red light on: Low baery
Blue light and red lights off: In Standby
Camera Buons:
Long press power switch for 3 seconds: Power-on/Power-off
Long press reset buon for 3 seconds: Reset to enter pairing state (The red light flashed
slowly aer the voice prompt)
02/Specificaon & Interface Descripon
①Antenna
②HD Lens
③Infrared LEDs
④Microphone
⑤Network Indicator
⑥PIR Sensor
⑦White LED Spotlight
⑧Adjusng Screw
⑨Release Buon
⑩Power Switch
⑪Loudspeaker
⑫Charge Indicator
⑬Micro SD Card Slot
⑭Retaining Screw
⑮Reset Buon
⑯Micro USB Port
3
2.2 Base Staon
2.3 NVR
①Antenna
②Micro SD Card Slot
③Pairing Buon
①Antenna
②3.5mm Audio Output
③VGA
④HDMI
⑤RJ45 Ethernet Port
⑥USB Port
⑦Power Port
④Reset
⑤RJ45 Ethernet Port
⑥Power Port
⑦Loudspeaker
⑧Network Indicator
⑨Camera Status Indicator
4
RESET DC 5V
LAN
Micro SD SYNC
NET
1
2
3
4
03/Download ZOSI CLOUD App
3.1 Search “ZOSI CLOUD” in App Store or Android Market, or scan the
QR code below to download on your smartphone (please grant the App
to obtain the corresponding permission for the first me use,
otherwise, it will cause the device fails to add, or when the camera
triggers moon detecon or alarm, the mobile phone cannot receive
the alarm push.)
Note: iOS Version required iOS 9.0 or above. Android Version requires
5.0 or above.
3.2 Register an Account
New user need to sign up by email or phone number, tap “Sign Up” and
follow the instrucons to sign up and log in.
5
04/Add Device
●4.1 Add Base Staon to APP
●4.1.1 Plug in base staon, connect the base staon to the router
connected to WAN with a Ethernet cable. And then scan QR code on
the base staon with your mobile phone and follow the prompt to add
devices. You can also scan and add in LAN (please ensure your mobile
phone and base staon are in a same LAN). Cameras paired with the
base staon will directly display on the device list aer the base staon
is successfully added.
Note: Please insert Micro SD card into the base staon before power-
ing on, otherwise the device cannot correctly read the memory card.
●4.1.2 Pair Cameras with Base Staon
Note: Baery cameras have been paired with the base staon, no
pairing is required. But if the pairing informaon between the camera
and base staon is cleared, you need to re-pair the devices, and follow
the steps below:
1) Place the cameras near the base staon at a distance of 30~100cm.
2) When the baery camera is turned on, press and hold the reset
buon for 3-5 seconds and you will hear a voice prompt from the
camera “Reset succeed, start pairing.” And then press and hold the
base staon pairing buon for 3-5 seconds and you will also hear a
voice prompt from base staon and start pairing. Aer that, both of the
cameras and the base staon will give out a voice prompt to indicate
that pairing succeed.
●4.2 Add the NVR to APP
●4.2.1 Connect NVR to Internet with an Ethernet cable aer plugging
in NVR, and then scan the QR code on NVR with your mobile phone and
follow the prompts to add devices. You can also scan and add in LAN
(please ensure your mobile phone and NVR are in a same LAN). Camer-
as paired with NVR will directly display on the device list aer NVR is
successfully added.
Note: Please install hard disk into NVR before powering on, otherwise
the device cannot correctly read the hard disk.
6
●4.2.2 Pair Cameras with NVR
Note: Baery cameras have been paired with the NVR, no pairing is
required. But if the pairing informaon between the camera and NVR
is cleaned, you need to re-pair the devices, and follow the steps below:
1) Place the camera near the NVR at a distance of 30~100cm.
2) When the baery camera is turned on, press and hold the reset
buon for 3-5 seconds and you will hear a voice prompt from the
camera “Reset succeed, start pairing.” And then turn on pairing
funcon of the NVR to add cameras. Aer that, the cameras will give
out a voice prompt to indicate that pairing succeed.
●4.3 Alarm, Preview, Playback and Device Sharing
●4.3.1 Click the App pushed or the Message icon in the App to check
the details of alarms.
●4.3.2 Click the Play icon on the device list and enter the preview
interface to enjoy live view and 2-way audio, etc.
●4.3.3 Click Playback or Cloud icon to view the recorded video on
device or on Cloud. NOTE: Cloud services need subscripon before use.
●4.3.4 Click Share icon to share cameras with others.
7
8
05/Camera Installaon
●5.1 You can place it on any flat surface: table, chair, floor etc..
●5.2 Install with Wall Mount
●5.2.1 Drill 5 holes according to the posion of mounng base,
and mount the base on the wall with the included pack of screws.
●5.2.2 Lock the two slots on the camera base to the hooks on
mounng base.
Install Mounng Base
Aach the Camera
Autres manuels pour C309
1
Table des matières
Langues :
Autres manuels ZOSI Appareil photo numérique
