ZMODO Greet Pro Manuel utilisateur
Greet Pro with Beam
Quick Start Guide
Screwdriver &
Interchangeable
Bit
Greet Pro
Masonry
Drill Bit
Spare Security
Screws
Mounting Screws
& Anchors (4)
Mounting
Level
Quick Start Guide
1
The Greet Pro allows you to answer your door from any
location and it is powered by your home's existing
mechanical doorbell chime. The Beam can extend the
range of 2.4GHz networks, and can be used to connect
your Greet Pro to a 2.4GHz WiFi network. It can also work as
a doorbell chime when paired with a Zmodo Smart Doorbell.
Getting to know your Kit
What’s in the box:
Power
Accessory
Beam
1
Mounting Bracket
(attached)
Greet Pro with Beam
Quick Start Guide
1
IMPORTANT! Before you begin, make sure
that the power to your doorbell is turned
off. Check your circuit breaker for a switch.
Before you begin:
2Mounting your Greet Pro
Remove your existing doorbell button. Once you’ve
removed your old doorbell, make sure that the two wires
used to connect your doorbell button remain exposed.
The Greet Pro was designed to seamlessly replace a pre-
existing doorbell button with a mechanical doorbell chime.
If you do not have a mechanical doorbell, you must attach
a 20 ohm/10 watt resistor (not included) between the
connected doorbell and one wire from the power source.
Failing to do so will cause permanent damage to your
Greet Pro and your warranty will be voided.
You will need a strong 2.4GHz/5GHz WPA-PSK/WPA2-
PSK WiFi network near your doorbell.
Make sure that your existing doorbell wiring is connected
to a mechanical doorbell chime and a transformer with a
low-voltage of 10VAC-36VAC.
Warning! Do not directly connect the doorbell to the
primary power source (110/120VAC and 220/230/240VAC).
Mounting
2
3
Note: Use the provided screws with anchors when mounting on brick,
concrete, or stucco. When mounting on wood or vinyl, you may use the
screws directly without anchors.
Mark and drill the appropriate holes in the wall for the
mounting bracket. Snap the provided level onto the
mounting bracket and align the bracket against the wall
where you would like to install your doorbell. Using the
bracket as a guide, mark the wall with the four
corresponding holes for screws. Remove the mounting
bracket from the wall and detach the provided level. Drill
four holes slightly smaller than the wall anchors using the
provided drill bit.
2Remove the mounting bracket from Greet Pro. Take your
Greet Pro out of the packaging and slide down to remove
the mounting bracket as shown below:
Slide down
Once the bracket is secure, fasten the two wires to the
terminals on the bracket. Ensure each wire is making
contact with the metal plating of each terminal. You can
fasten either wire to either terminal, but make sure that the
wires are not touching each other.
4Fasten the mounting bracket onto the wall and connect
the wires to the wire terminals. Tap the wall anchors with a
hammer until the anchors are flush against the wall. Using
the Philips tip for the provided screwdriver and the
provided screws, fasten the bracket into place. Make sure
that the two wires from Step 1 are fed through the opening
and exposed.
Attach Greet Pro to the mounting bracket. First, attach the
security screw partially so that it's easier to tighten it when
the Greet Pro is mounted. Fasten the screw to the bottom
as shown below, using the smaller head on the provided
screwdriver. Then mount the Greet Pro onto the mounting
bracket by pushing firmly and sliding downwards.
5
Note: If you are having difficulty sliding Greet Pro onto its mounting
bracket, please loosen the security screws.
4
Installing your Power Accessory:
Note: The power accessory is an optional add-on to regulate the power
that flows to your Greet Pro. If you hear a buzzing sound from your chime,
installing the power accessory will solve the issue. Before installing the
power accessory, please make sure that the power to your doorbell is
turned off from your circuit breaker.
6
Tighten the security screws until secure and restore the
power to your doorbell from your circuit breaker. Once
Greet Pro is securely attached to its bracket, tighten the
security screws completely using the smaller bit on the
provided screwdriver. You may now restore power to the
doorbell. Your Greet Pro should power on and the Status
Light will begin to blink green after a few moments.
5
3
Loosen the screws of the chime terminals which have
wires connected. Your chime may have a wire connected
to the front door labelled “FRONT” and a wire connected
to the transformer labelled "TRANS". Using a screwdriver,
loosen the screws on the “FRONT” terminal and “TRANS”
terminal.
2
1
Remove the cover of your mechanical chime. First,
locate your mechanical chime inside of your home. The
mechanical chime is the device that rings when your
doorbell is rung, and may commonly be a white box
mounted on the wall.
Connection Diagram
Metal BarMetal Bar
Original Chime Connection Chime Connection with Power Accessory
Metal Bar
REAR
TRANS
FRONT
Metal Bar
Connection Diagram after installing Greet Pro and Power Accessory
REAR
TRANS
FRONT
6
Fasten the two wires from the power accessory to the
terminals you just loosened the screws on your
mechanical chime. You can fasten either wire to either
terminal as long as there is no contact between the wires.
Power
Accessory
Chime
REAR
TRANS
FRONT
Transformer
Greet Pro
Fasten your power accessory to the mechanical chime.
Peel the cover off of the adhesive backing and press the
power accessory firmly onto the side of the mechanical
chime, the cover of the chime, or the wall near the
chime. You may want to find a suitable location to mount
your accessory before exposing the adhesive. Note:
Make sure that the wires don’t make contact with the
metal bars, otherwise the chime will not properly sound.
4
Install the cover on your chime, and restore power to
your system.
5
7
3
We are constantly working to improve our product and app. Please visit
www.zmodo.com/support for updated instructions, manuals, and more.
3Configuring your Beam
Make sure you know the SSID (WiFi network name) and
password of the 2.4GHz WPA-PSK/WPA2-PSK WiFi
network that you want your Beam to connect to. Your
network cannot be hidden.
The following instructions will help you configure your
Beam for initial use. The Beam can extend the range of
2.4GHz WiFi networks, and can be used to connect
your Greet Pro to a 2.4GHz WiFi network. For detailed
instructions and troubleshooting, please visit:
www.zmodo.com/support
Before you begin:
Place your Beam within range of your wireless router.
8
Log in and press in the upper
right corner. Select "Add Device".
+
1
Zmodo
TM
Download and install the Zmodo app from Google Play " "
TM ®TM
or the App Store (Compatibility: iOS 9.0+ or Android
4.0+). Launch the app and sign up for a free Zmodo
account. All of your devices will be bound to this account.
9
Select the “Tap here to add a Beam”
option at the bottom of the page to
connect your Beam. Your Beam will
be added to your Zmodo account.
2
4
3
Select the network named “AP_ZMD”
and connect to it.
Note: If you see a "No Internet Connection" error
message, please ignore it and connect anyway.
Follow the on-screen instructions and
select “Tap here to begin setup” to go
to the WiFi settings page on your
smartphone.
“AP_ZMD”
AP_ZMD
Note: If you are using an iOS device, you will need
to manually go to the WiFi settings page on your
smartphone.
Autres manuels pour Greet Pro
2
Table des matières
Autres manuels ZMODO Accessoires
