ZMODO Greet Pro Manuel utilisateur
Greet Pro
Quick Start Guide
Screwdriver &
Interchangeable
Bit
Greet Pro Mounting Bracket
(attached)
Masonry
Drill Bit
Spare Security
Screws
Mounting Screws
& Anchors (4)
Mounting Level Quick Start Guide
1
1
The Greet Pro allows you to answer your door from any
location. The Greet Pro is powered by your home's
existing mechanical doorbell chime. This quick start guide
will help you configure your Greet Pro for initial use. For
detailed instructions and troubleshooting, please visit:
www.zmodo.com/support
Getting to know your Greet Pro
What’s in the box:
Power
Accessory
Greet Pro
Quick Start Guide
2
1
IMPORTANT! Before you begin, make sure
that the power to your doorbell is turned
off. Check your circuit breaker for a switch.
Before you begin:
2Mounting your Smart Doorbell
Remove your existing doorbell button. Once you’ve
removed your old doorbell, make sure that the two wires
used to connect your doorbell button remain exposed.
The Greet Pro was designed to seamlessly replace a pre-
existing doorbell button with a mechanical doorbell chime.
If you do not have a mechanical doorbell, you must attach
a 20 ohm/10 watt resistor (not included) between the
connected doorbell and one wire from the power source.
Failing to do so will cause permanent damage to your
Greet Pro and your warranty will be voided.
You will need a strong 2.4GHz/5GHz WPA-PSK/WPA2-
PSK WiFi network near your doorbell.
Make sure that your existing doorbell wiring is connected
to a mechanical doorbell chime and a transformer with a
low-voltage of 10VAC-36VAC.
Warning! Do not directly connect the doorbell to the
primary power source (110/120VAC and 220/230/240VAC).
Mounting
3
Note: Use the provided screws with anchors when mounting on brick,
concrete, or stucco. When mounting on wood or vinyl, you may use the screws
directly without anchors.
Mark and drill the appropriate holes in the wall for the
mounting bracket. Snap the provided level onto the
mounting bracket and align the bracket against the wall
where you would like to install your doorbell. Using the
bracket as a guide, mark the wall with the four
corresponding holes for screws. Remove the mounting
bracket from the wall and detach the provided level. Drill
four holes slightly smaller than the wall anchors using the
provided drill bit.
2Remove the mounting bracket from
Greet Pro. Take your Greet Pro out of
the packaging and slide down to
remove the mounting bracket as
shown below:
Slide down
Once the bracket is secure, fasten the two wires to the
terminals on the bracket. Ensure each wire is making
contact with the metal plating of each terminal. You can
fasten either wire to either terminal, but make sure that
the wires are not touching each other.
4
4Fasten the mounting bracket onto the wall and connect
the wires to the wire terminals. Tap the wall anchors with
a hammer until the anchors are flush against the wall.
Using the Philips tip for the provided screwdriver and
the provided screws, fasten the bracket into place.
Make sure that the two wires from Step 1 are fed
through the opening and exposed.
5
Attach the Greet Pro to the mounting bracket. First,
attach the security screw partially so that it's easier to
tighten it when the Greet Pro is mounted. Fasten the
screw to the bottom as shown below, using the smaller
head on the provided screwdriver. Then mount the Greet
Pro onto the mounting bracket by pushing firmly and
sliding downwards.
5
Note: If you are having difficulty sliding Greet Pro onto its mounting
bracket, please loosen the security screws.
6
Tighten the security screws until secure and restore the
power to your doorbell from your circuit breaker. Once
Greet Pro is securely attached to its bracket, tighten the
security screws completely using the smaller bit on the
provided screwdriver. You may now restore power to the
doorbell. Your Greet Pro should power on and the Status
Light will begin to blink green after a few moments.
6
Installing your Power Accessory:
Note: The power accessory is an optional add-on to regulate the power
that flows to your Greet Pro. If you hear a buzzing sound from your chime,
installing the power accessory will solve the issue. Before installing the
power accessory, please make sure that the power to your doorbell is
turned off from your circuit breaker.
Power
Accessory
Chime
REAR
TRANS
FRONT
Transformer
Greet Pro
Connection Diagram
Metal BarMetal Bar
Original Chime Connection Chime Connection with Power Accessory
Metal Bar
REAR
TRANS
FRONT
Metal Bar
Connection Diagram after installing Greet Pro and Power Accessory
REAR
TRANS
FRONT
Fasten your power accessory to the mechanical chime.
Peel the cover off of the adhesive backing and press the
power accessory firmly onto the side of the mechanical
chime, the cover of the chime, or the wall near the
chime. You may want to find a suitable location to mount
your accessory before exposing the adhesive. Note:
Make sure that the wires don’t make contact with the
metal bars, otherwise the chime will not properly sound.
4
Install the cover on your chime, and restore power to
your system.
5
Fasten the two wires from the power accessory to the
terminals you just loosened the screws on your
mechanical chime. You can fasten either wire to either
terminal as long as there is no contact between the wires.
3
7
Loosen the screws of the chime terminals which have
wires connected. Your chime may have a wire connected
to the front door labelled “FRONT” and a wire connected
to the transformer labelled "TRANS". Using a screwdriver,
loosen the screws on the “FRONT” terminal and “TRANS”
terminal.
2
1Remove the cover of your mechanical chime. First,
locate your mechanical chime inside of your home.
The mechanical chime is the device that rings when
your doorbell is rung, and may commonly be a white
box mounted on the wall.
3Mobile Setup
We are constantly working to improve our product and app. Please visit
www.zmodo.com/support for updated instructions, manuals, and more.
Make sure that you have a strong WiFi connection at the
location of your Greet Pro. Visit www.zmodo.com/support
for advice on improving your WiFi signal range.
Make sure you know the SSID (WiFi network name) and
password of the 2.4GHz/5GHz WPA-PSK/WPA2-PSK
WiFi network that you want your Greet Pro to connect to.
Your network cannot be hidden.
TM
Download and install the "Zmodo" app from Google Play
TM ® TM
or the App Store (Compatibility: iOS 7.0+ or Android
4.0+). Launch the app and sign up for a free Zmodo
account. All of your devices will be bound to this account.
This quick start guide will help you configure your Greet
Pro for initial use. For detailed instructions and
troubleshooting, please visit:
Before you begin:
Zmodo
Make sure the network of the location where you install
the Greet Pro has at least 2Mbps upload speed to view
and 4Mbps upload speed when using the Zmodo Cloud
Service.
www.zmodo.com/support
8
Log in and press in the upper
right corner. Select "Add Device".
This device can be set up with a Zmodo Beam. If you own a
Beam, please follow the instructions in your Beam quick guide to
connect your device instead. Beam will only be able to Note:
connect your devices to a 2.4GHz network.
2
Connectwith
Beam
+
1
9
Select the “Zink” connection method
to connect your Greet Pro. Your Greet
Pro will be added to your Zmodo
account.
Autres manuels pour Greet Pro
2
Table des matières
Autres manuels ZMODO Accessoires
