ZKTeco SA32-E Manuel utilisateur

Single Door RFID Based Access Control

SA32-E/M

Thank you for choosing our product. Please read the instructions

carefully before operation. Follow these instructions to ensure that the

product is functioning properly. The images shown in this manual are

for illustrative purposes only.

New Firmware for 2.8/3/3.5-inch Color Screen

Product Overview

SA32-E

Single Door RFID Based Access Control

SA32-E is an Access Control Standalone Device with contact-less

smart card and password verications, which enables 3 verication modes

(Card only, PIN only, and Card & PIN) to ensure maximum safety and

exibility. With 1 Relay output (optional) and 1 PUSH (low) output,

1 door button Port and 1 doorbell Port, SA32 is simple but eective to use,

its convenience and adaptability allow it to be well deployed in residential

housing, oces and any other public facilities.

1. Specifications:

1.1Technical parameters:

NO Item Value

Operating voltage

DC 12V±10%

Operating current

< 100mA

Dimensions

120mm×78mm×22mm

Weight

110g

Ambient temperature



—60



Relative humidity

20%—80%

Storage

1000users

Card type (alternative)

EM(ID) card(IC card for options)

Card reading distance

－

15CM

1.2 Factory Default:

1.3 Light and Sound indicates:

Light: red and green

Light Description

Access control status

Red light flash every 1 sec

（

Slow flash

）

Holding state

Red light is always ON

Programming state

Green light is always ON within Open time

Unlocking state

Green light flash every 0.5sec (Fast flash)

Pending further action

Sound ：buzz

Description

I ndicates

1 short buzz

Valid input

3 short buzz

Invalid input

1 long buzz

Program success

Continuous long buzz

Restoring factory programming passwords

Programming

Password

123456 Common Access

Password

None

Backlight Auto (for options) Relay Unlock

output 5 Seconds

W26 port Input (for options) Security mode OFF

Open mode

Card or Access Password

Access Password include Private Access Password (PIN) and

Common Access Password

2. Installations Guide

JP1 terminal:

JP2 terminal:

Mark

Color

Function

Remark

+12V

Red

Power+

For options

GND

Black

Power-

DATA0

Green

WG DATA0

DATA1

White

WG DATA1

Brown

Relay NC output

COM

Blue

Relay Com output

Purple

Relay NO output

Mark

Color

Function

+12V

Red

Power+

GND

Black

Power-

PUSH

BLUE

Low level output

OPEN

Yellow

Door Release

BELL

Grey

BELL

White

BELL

emark:

let relay drive electric -

“-” poles.

lock, please connect a reverse diode with the lock’s “+” and

Wiring diagram:

3.2 To reset to Factory Programming Password (123456)

Step1、Turn off power and connect bin 2&3 of RST(S1)。

Step2、Turn on power and buzzer gives 3 long buzz with green light flash fast。

If need to set Manager Card, now read two empty cards first one as Manager Add Card and

Second one as Manager Delete Card with red light flashing and continuous short buzz .

Step3、Turn off power, disconnect bin2&3 and connect bin 1&2 of RST。

Step4、Turn on power again.

3.3 How to use Manager Card - MAC & MDC

To add a card user in standby mode: read MAC read new cards read MAC

To delete a card user in standby mode: read MDC read registered cards read MDC

To delete all users in standby mode: read MDC read MAC read MDC

Remark: User cards can be added or deleted continuously.

3.4 User ID No. explain

User ID is auto-generating 4-digit number started at 0001. The number increases with adding

user one by one and ignores deleting user. Common Access Password has no ID.

3.5 How to change PIN (When open mode: card+ PIN)

After reading card and input corresponding PIN to open the door, within 5 seconds, long press #

until the green lights flash fast. and then input new PIN # new PIN # , new PIN

changed successfully with a long buzz.

3. Programming Guide

ZKTeco Biometrics India Pvt. Ltd. www.zkteco.in E-mail: [email protected]

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ZKTeco Contrôleurs d'accès IP

ZKTeco

ZKTeco BioPro SA20 Manuel utilisateur

ZKTeco

ZKTeco IN710 Manuel utilisateur

ZKTeco

ZKTeco White LCD Series Manuel utilisateur

ZKTeco

ZKTeco MA500 Guide de dépannage

ZKTeco

ZKTeco F19 Manuel utilisateur

ZKTeco

ZKTeco C2-260 Manuel utilisateur

ZKTeco

ZKTeco FaceKiosk-H13A Manuel utilisateur

ZKTeco

ZKTeco inBIO 480 Mode d’emploi

ZKTeco

ZKTeco ProCapture-WP Manuel utilisateur

ZKTeco

ZKTeco SpeedFace-V3L Manuel utilisateur

ZKTeco

ZKTeco MA500 Guide de dépannage

ZKTeco

ZKTeco ProBio Manuel utilisateur

ZKTeco

ZKTeco LockerPad-7B Manuel utilisateur

ZKTeco

ZKTeco TF1600 ZKTeco Manuel utilisateur

ZKTeco

ZKTeco SpeedFace-V3L Manuel utilisateur

ZKTeco

ZKTeco ProBio Manuel utilisateur

ZKTeco

ZKTeco LF10 Manuel utilisateur

ZKTeco

ZKTeco FaceKiosk-H10A Manuel utilisateur

ZKTeco

ZKTeco ProMA Series Manuel utilisateur

ZKTeco

ZKTeco F17 Manuel utilisateur

ZKTeco

ZKTeco FR1200 Fiche technique

ZKTeco

ZKTeco ProFace X Series Manuel utilisateur

ZKTeco

ZKTeco ZPad Plus Manuel utilisateur

ZKTeco

ZKTeco C5S120 Mode d’emploi

Manuels Contrôleurs d'accès IP populaires d'autres marques

Jantar

Jantar REX A-1-9 Manuel utilisateur

2N Access Unit Feuille d'instructions

Kedacom

Kedacom KSCA120 Series Manuel utilisateur

H3C

H3C WX2880X Manuel utilisateur

G4S

G4S S870-EX Mode d’emploi

PRASTEL

PRASTEL M2000PE Manuel utilisateur

Allegion

Allegion interflex IF-281 Cylinder Manuel utilisateur

TECOM

TECOM TS1067E Manuel utilisateur

Fermax

Fermax Memokey 100C Guide de l'utilisateur

Fermax

Fermax CITYLINE MEMOKEY Mode d’emploi

Software House

Software House iSTAR Pro 2U RM Mode d’emploi

AKCP

AKCP SP+ Manuel utilisateur

Bpt

Bpt HNA/102 Manuel utilisateur

Civintec

Civintec CV9601T-T-1F Manuel utilisateur

BioMax

BioMax N-X90W Manuel utilisateur

FingerTec

FingerTec s-Kadex Manuel utilisateur

H3C

H3C WX5002ACCESSCONTROLLER Manuel utilisateur

C Prox Ltd

C Prox Ltd DPN-2 Manuel utilisateur