ZKTeco PB3000 Series Manuel utilisateur
Installation Guide
PB3000
PB3000 Installation Guide
1
Contents
Chapter 1 Cable Embedding......................................................................................................................................................................................................1
Chapter 2 Cabinet Installation...................................................................................................................................................................................................2
Chapter 3 Boom Installation .......................................................................................................................................................................................................3
Chapter 4 Control board introduction.................................................................................................................................................................................4
Chapter 5 Troubleshoot .................................................................................................................................................................................................................5
PB3000 Installation Guide
1
Chapter 1 Cable Embedding
1) Prepare φ25 protective sleeve and cable in advance.
2) Route cables to be connected through protective sleeves.
3) Use a tool to open a cable tray on the ground, see figure 1-1.
Figure 1-1 Cable embedding
The power wire is wrapped
and protected using the wire
sleeve when laid out under
the ground (the strong
current should be separated
from the weak current)
Control
room Screw pad
Ground
Ground
Cabinet
Expansion bolt
4-M12
Base concrete
A standard power wire RVV3*1.0
A signal line RVV4*0.5
PB3000 Installation Guide
2
Chapter 2 Cabinet Installation
1) Use Bolt Holes Dimensioning to mark the installation position of the cabinet.
2) Drive four expansion bolts into the Bolt Holes Dimensioning, as shown in figure 2-1.
3) Open the access door and install the parking barrier.
4) Install screw pads and use a wrench to tighten nuts, as shown in figure 2-2.
5) Close the access door.
Figure 2-1
Figure 2-2
Screw pad
Ground Ground
Base
concrete
Chassis
Expansion bolt
PB3000 Installation Guide
3
Chapter 3 Boom Installation
1) Take out the booms.
2) Install the booms. (If your purchase is PB3010L/R, there will be only one boom. If your purchase is PB3030L/R
or PB 3060L/R there will be a main boom and a vice boom which need to be connected together. See figure
3-1.)
3) Putting the vice boom insert into the main boom, then fastened by 2 screws.
4) Installing the boom to the chassis, as shown in figure 3-2.
Figure 3-1
Figure 3-2 Installing the Boom to the Chassis
Connect the main boom with vice together by 2 screw
Screw
Iron piece
Boom
PB3000 Installation Guide
4
Chapter 4 Control board introduction
1) Interface of the Main Control Board
Delete All Transmitter
Press K4 setting button until D8 yellow light flashes. Hold on K4, press stop button on control board until D9 red
light flashes one time. All the registered transmitters will be deleted after successful operation.
Register the transmitter
Press K4 setting button until D8 yellow light flashes. Hold on K4, press any button on transmitter until D9 red light
flash one time. Maximum 7 different code transmitters can be registered.
2) Interface of the Extension board
Control board
PB3000 Installation Guide
5
Chapter 5 Troubleshoot
1) If the boom fails to fall into a level position, adjust position A; if the boom fails to be lifted upright, adjust
position B. See Figure 5-1.
2) If the boom shakes during falling or lifting, adjust position C. The shaking that occurs during lifting is caused
by the overlarge spring force. In this case, loosen the screws. If the boom shakes during falling, tighten the
screws. See Figure 5-2.
3) Use the motor handle to lift the boom in the case of a power failure, See Figure 5-3.
Figure 5-1 Figure 5-2 Figure 5-3
Position C
Position A Position B
Handle
Autres manuels pour PB3000 Series
1
Table des matières
Autres manuels ZKTeco Barrière automatique
ZKTeco
ZKTeco BGM1000 Series Manuel utilisateur
ZKTeco
ZKTeco ProEntrance Series Manuel utilisateur
ZKTeco
ZKTeco BG500 Series Manuel utilisateur
ZKTeco
ZKTeco BG1045L-LED Manuel utilisateur
ZKTeco
ZKTeco CMP-300 Manuel utilisateur
ZKTeco
ZKTeco BG1000 Series Manuel utilisateur
ZKTeco
ZKTeco CMP-200 Series Manuel utilisateur
ZKTeco
ZKTeco SBTL2000 Manuel utilisateur
ZKTeco
ZKTeco LB330 Manuel utilisateur
ZKTeco
ZKTeco SBTL300 Series Manuel utilisateur
