Zipr Roo Manuel utilisateur
zip’r Roo
Mobility Scooter Operation Manual
Zip’r™ Mobility LLC
North Bend, WA
(800) 760-9107
www.zipr.com
“Simplicity in Mobility”
2
TABLE OF CONTENTS
I. INTRODUCTION…………………………........................................................3
II. SPECIFICATIONS AND STRUCTURE………………………………....................4-6
III. INITIAL ASSEMBLY............................................................................7-8
IV. DISASSEMBLY......................................................................................9
V. COMFORT ADJUSTMENTS..................................................................10
VI. OPERATION..................................................................................11-12
VII. BATTERY AND CHARGING........................................................13-15
VIII. CARE AND MAINTENANCE.......................................................16-17
IX. SAFETY .......................................................................................18-22
X. ELECTROMAGNETIC INTERFERENCE...................................................23
XI. TROUBLESHOOTING .........................................................................24
XII. WARRANTY INFORMATION..........................................................25
ZIP’R MOBILITY CONTACT INFORMATION
(800) 760-9107 www.zipr.com
MY AUTHORIZED DEALER: _________________________________________
DEALER TELEPHONE #: _________________________________________
PRODUCT SERIAL #: _________________________________________
3
INTRODUCTION
Congratulations on your purchase of the Zip’r Roo travel scooter. Many important safety, operating,
and maintenance instructions are included in this operation’s manual. We urge you to read the entire
manual carefully before you attempt to operate your scooter. These instructions were compiled for
your benefit. Your understanding of these instructions is essential for the safe operation of your new
scooter.
Zip’r Mobility is not liable for damage to property or personal injury from the failure of any user to
properly follow the instructions and recommendations set forth in this manual and/or on the scooter.
Safety words are used throughout this manual to indicate hazards and/or unsafe actions. Please refer to
the table below for definitions of the safety words.
IMPORTANT NOTES
Please note that the information contained in this document is subject to change without
notice. Please see www.zipr.com for updated copies of this manual.
Failure to follow the instructions, warnings, and notes in this manual and those located on your
Zipr PC can result in personal injury, product damage, or malfunction and void Zipr’s product
warranty.
It is assumed that an authorized Zipr dealer has properly fit the product to the user and has
instructed the user on proper use/operation. If you purchased this product over the internet or
from a previous owner and you have questions about the safe use and/or proper maintenance
the please refer to our website www.zipr.com or contact Zipr directly at (800)760-9107.
SAFETY WORD DEFINITION
CAUTION
Caution indicates potentially hazardous situation which, if not avoided,
could result in product damage or malfunction
DANGER Danger indicates a probably hazardous situa
tion which, if not
avoided, will result in personal injury, product damage, or malfunction.
PROHIBITED
Prohibited indicates that such actions should not be performed at any
time. Performing a prohibited action can cause personal injury,
product damage, or malfunction.
REQUIRED
Required indicates that these actions should be performed as
specified. Failure to perform required acti
ons can cause personal
injury, product damage, or malfunction.
WARNING
Warning indicates a potentially hazardous situation which, if not
avoided, could result in personal injury, product damage, or
malfunction.
4
II. SPECIFICATIONS AND STRUCTURE
DRIVE WHEEL 7.3" (186mm) solid foam filled
FRONT WHEEL 7.16" (182mm) solid foam filled
ANTI-TIP WHEEL 2.2" (56mm) solid
SPEED MAXIMUM Fwd = 3.5 mph / Reverse = 2.2 mph
BRAKING SYSTEM Intelligent brake
GROUND CLEARANCE 2" (51mm)
TURNING RADIUS 31.5" (800mm)
DIMENSIONS 37.4" L x 19.5" W x 32.4" H (950 x 495 x 825mm)
SEATING 15" L x 16.5" W x 17.5" H, Folding foam filled
DRIVE SYSTEM Single motor drive
BATTERIES 12V 12 AH x 2, Sealed, deep cycle
MOTOR POWER 24v 180w
PER CHARGE RANGE 10 miles (16.1 kilometers)
CHARGER 24V 2A portable
WEIGHT CAPACITY 250 lbs (91 kg) maximum
CLIMBING SLOPE 8% maximum
CHARGING TIME 10 hours
WEIGHT (REAR SECTION) 31 lbs (14 kg)
WEIGHT (FRONT SECTION) 21 lbs (9.5 kg)
WEIGHT (SEAT) 22 lbs (10 kg)
WEIGHT (BATTERIES w/CASE) 21 lbs (9.5 kg)
SPECIFICATIONS
5
II. SPECIFICATIONS AND STRUCTURE
Your scooter mainly consists of four parts: The front section, rear section, seat, and battery case. The
tiller console, handle bars, and footplate are located on the front section. The motor, brake system and
controller are located in the rear section. See Figure 1.
6
II. SPECIFICATIONS AND STRUCTURE
TILLER CONSOLE (Figure 2)
CHARGING SYSTEM (Figure 3)
7
III. INITIAL ASSEMBLY
In order to avoid shipping damage, the batteries and the seat unit are not separately packaged, so you
will need to assemble them onto the main frame of your scooter.
OPENING THE PACKING BOX
Open the packing box of your new scooter and remove all of the protective materials, then carefully
remove the scooter and separated components from the box.
ADJUSTING ANGLE OF TILLER (Figure 4.)
• Loosen the tiller adjustment knob located at the base of the tiller
• Lift the tiller up to a proper angle for yourself
• Tighten the tiller adjustment knob
ASSEMBLING THE SEAT POST (Figure 5.)
• Insert the chrome seat post into the seat post frame located on the rear section
• Align the adjustment pin hole
• Insert the adjustment pin into the aligned holes and out through the opposite side
8
III. INITIAL ASSEMBLY
ASSEMBLING BATTERY UNIT (Figure 6. & 6.1)
• Lower the battery case into the trough and ensure that the electrode terminals are aligned.
• Loosen safety locking knob located directly behind the black seat post, turn the locking cap such that it
is centered over each side of the battery case, and then retighten the locking knob.
CAUTION!
Please always keep the battery case metal contacts (electrodes) clean. Dirty contacts can lead to the
malfunction of the batteries.
ASSEMBLING SEAT UNIT (Figure 7.)
• Lower the seat onto the chrome seat post
• Pull up on the seat-lock lever (located under the seat), adjust seat to the position, and release then
release the lever. The seat will lock into position.
• Insert the armrests into seat frame and tighten the armrest locking knobs located under the seat.
INSTALLING BASKET (Figure 8.)
• Lower the basket frame onto the basket bracket (pre-installed on the front of the tiller).
Figure 6.1
9
IV. DISASSEMBLY
Your Zip’r Roo scooter has been designed to easily disassemble and transport. You can easily
disassemble the scooter into four pieces, the front section, the rear section, the seat unit and the
battery case (Figure 9).
DISASSEMBLY
• Lift the seat off of the scooter seat post.
• Loosen the battery case safety lock cap (Figure 6.1) and remove battery case from scooter (Figure 6.).
• Remove the front to rear wire harness connection (Figure 10.)
• Lift up on the yellow plastic ring latch until the scooter is sitting on its rear end (Figure 11.)
• With both hands remove the front section of the scooter from the rear section (Figure 12.)
• Loosen the tiller adjustment knob, lower the tiller, and retighten the tiller adjustment knob.
• You can now transport the four sections (front, rear, seat, and battery case).
10
V. COMFORT ADJUSTMENTS
Before operating the scooter, you may find the need to make some adjustments to increase your
comfort, such as the seat height, armrest width, and tiller angle.
WARNING!
Remove the key from the key switch before adjustments. Never attempt to do adjustments while the
scooter is in motion.
SEAT HEIGHT ADJUSTMENT
• Lift up on the seat lock lever and pull the seat off of the seat post.
• Remove the seat post adjustment pin.
• Choose the appropriate seat height and re-insert the seat post adjustment pin.
• Re-install the seat.
SEAT ROTATION (Figure 13.)
• Pull up on the seat lock lever.
• Rotate the seat to the desired position.
• Release the lock lever in place.
ARMREST WIDTH ADJUSTMENT (Figure 14.)
• Loosen the armrest adjustment knobs located beneath the
seat frame.
• Move the armrests to the desired position.
• Tighten the armrest adjustment knobs.
Figure 14
Autres manuels pour Roo
1
Table des matières
Autres manuels Zipr Scooter
Manuels Scooter populaires d'autres marques
First Choice Mobility
First Choice Mobility Roma Medical Corella S741 Manuel utilisateur
Carrera
Carrera impel Manuel utilisateur
Afikim
Afikim Superlight SL-3 Manuel utilisateur
CareCo
CareCo ZOOM Manuel utilisateur
Douglas
Douglas Vespa G.S. Manuel utilisateur
Gazelle
Gazelle with BOSCH System Manuel utilisateur