Zennio ZCL-MCC Manuel utilisateur

MCC

Multiroom Climate Controller

ZCL-MCC

USER MANUAL

Application program version: [2.0]

User manual edition: [2.0]_a

www.zennio.com

MCC

http://www.zennio.com Technical Support: http://support.zennio.com

CONTENTS

Contents........................................................................................................................................ 2

Document Updates ....................................................................................................................... 3

1 Introduction .......................................................................................................................... 4

1.1 MCC (Multiroom Climate Controller)............................................................................ 4

1.2 Installation..................................................................................................................... 5

2 Functionality.......................................................................................................................... 7

2.1 Configuration Check...................................................................................................... 7

2.2 Operation Roles............................................................................................................. 9

2.2.1 Master ............................................................................................................... 9

2.2.2 Slave ................................................................................................................ 11

2.3 Master/Slave Role Selection ....................................................................................... 14

2.4 LED Notifications......................................................................................................... 15

2.5 Initial States................................................................................................................. 16

3 Configuration....................................................................................................................... 18

3.1 General........................................................................................................................ 18

3.2 Hospitality Thermostat................................................................................................ 20

ANNEX I. Communication Objects............................................................................................... 21

MCC

http://www.zennio.com Technical Support: http://support.zennio.com

DOCUMENT UPDATES

Version

Changes

Page(s)

[2.0]_a

Changes in the application program:

•Update of the Hospitality Thermostat function to

version 1.0.0 (corresponding user manual: 1.0_a).

•Number of thermostats available: 13.

[1.5]_a

Changes in the application program:

•Update of the Hospitality Thermostat function to

version 0.5.3 (corresponding user manual: 0.5_a).

[1.4]_a

Changes in the application program:

•Update of the Hospitality Thermostat function to

version 0.4.6 (corresponding user manual: 0.4_a).

[1.3]_a

Changes in the application program:

•Update of the Hospitality Thermostat function to

version 0.3.6 (corresponding user manual: 0.3_a).

[1.2]_b

Changes in the application program:

•Update of the Hospitality Thermostat function to

version 0.2.4 (corresponding user manual: 0.2_b).

MCC

http://www.zennio.com Technical Support: http://support.zennio.com

1INTRODUCTION

1.1 MCC (MULTIROOM CLIMATE CONTROLLER)

MCC (Multiroom Climate Controller) from Zennio is an in-line controller aimed at

managing and controlling the climate of multiple hotel rooms (or any other type of guest

rooms, e.g., residential or hospital rooms). To that end, it is possible to enable up to

thirteen thermostats independently.

Given how critical it is that a single device controls the climate of several rooms, it is

possible to have two exactly alike MCCs (and with the same configuration) working in

the same system, one of them as a master and the other as a slave. Thus, the

master device will operate normally while the slave remains on standby to take control

if the master fails.

The most outstanding features of MCC are:

System configuration for operation with a single device or two devices with

Master-Slave roles.

Up to 13 independent Hospitality thermostats.

Communication objects and LEDs indicators of master/slave role, slave

error and configuration error.

MCC

http://www.zennio.com Technical Support: http://support.zennio.com

1.2 INSTALLATION

MCC connects to the KNX bus through the on-board KNX connector. Once the device

is provided with power from the KNX bus, both the individual address and the

associated application program can be downloaded.

Figure 1. MCC - Element Diagram.

The main elements of the device are described next.

Test/Prog. Pushbutton (1): a short press on this button sets the device into

the programming mode, making the associated LED (2) light in red.

Note: if this button is held while plugging the device into the KNX bus, the

device will enter into safe mode. In such case, the LED will blink in red.

Master Status LED (3): LED indicator that lights up when the device is

running as a master.

Slave Status LED (4): LED indicator that lights up when the device is running

as a slave.

Missing Slave LED (5): LED indicator that lights up when no slave MCC is

found in the installation. Note that this does not prevent the master MCC from

running normally.

1. Prog./Test Button.

2. Prog./Test LED.

3. Slave Status LED.

4. Master Status LED.

5. Missing Slave LED.

6. Configuration Error LED.

7. KNX Connector.

MCC

http://www.zennio.com Technical Support: http://support.zennio.com

Configuration Error LED (6): LED indicator that will blink in red if, although

one master MCC and one slave MCC have been found in the installation,

their configurations do not match.

To get detailed information about the technical features of the device, as well as on the

installation and security procedures, please refer to the corresponding Datasheet,

bundled with the original package of the device and also available at www.zennio.com

MCC

http://www.zennio.com Technical Support: http://support.zennio.com

2FUNCTIONALITY

As indicated in the introduction, the aim of this device is performing an in-line climate

control of multiple hotel rooms (or any other guestrooms, such as residential rooms

or hospital rooms), where it is necessary to ensure that the system keeps running

despite of occasional device faults.

The following sections describe the different roles that the device can assume and all

the checks and notifications performed during the process.

2.1 CONFIGURATION CHECK

MCC is designed to operate in pairs: two MCCs with the same configuration are

recommended to simultaneously work together in the same installation. Device

redundancy is justified by how critical a fault in one of them would be, as the climate

system of several rooms depends on it. However, it is not mandatory to install two

MCCs to make the system work and it is possible to configure it to act as a single

device.

To have two devices working together properly it is necessary to configure them

identically: same parameters, group addresses and associations. It is recommended to

first configure a device and, after validating the configuration, making an exact copy

in the ETS project, keeping the group addresses.

The device will check that its configuration matches that of its analogue. Therefore,

after each reboot both will exchange a checksum value, which depends on:

Number and application program version.

Parameters.

Table of communication objects (flags and size of the communication

objects).

Group address table.

Associations table.

MCC

http://www.zennio.com Technical Support: http://support.zennio.com

Every time the master and the slave send the bus a master / slave role confirmation

notification (see sections 2.2.1 and 2.2.2), they both will also re-send their checksum

values through a communication object with the writing and transmission flags

enabled, in order to transmit and receive information through it. If the received

checksum is different from the one sent (i.e., the one calculated internally):

Everything related to the thermostatic control will stop working: no more

sendings will take place, even if the device is working as a master (see

section 2.2.1).

The role notification sending will stop (master / slave).

The “Configuration error” communication object will be transmitted with

value ‘1’ every 30 seconds.

The checksum calculated internally will be transmitted with a one-second

delay, to make it possible to check at any time whether the two configurations

still do not match.

All LEDs will turn off except the configuration error LED, which will bink

every one second.

The device will remain in the above state until the expected checksum value is

received (i.e., a value that matches with the one internally calculated), after which the

device will reboot as if it had just been programmed.

Once the device reboots, it will operate as if it had never detected the wrong

configuration, thus, maintaining the same state it had before the configuration error

detection. Then, it will apply everything specified in section 2.5.

After a restart, the object “Configuration error” is always transmitted with value ‘0’.

MCC

http://www.zennio.com Technical Support: http://support.zennio.com

2.2 OPERATION ROLES

MCC may be operating as a master, as a slave or under an “undefined” state:

The master aims at actually controlling the room climate.

The slave remains waiting for a failure in the master, to take over the climate

control.

A device is operating as “undefined” when it has not been determined yet

whether it must operate as a master or as a slave.

The device role will be notified via communication object (this process is detailed in

following sections) and by two LEDs specifically included for this purpose: the LED

corresponding to the current role lights up (master LED indicator or slave LED

indicator); if there is no role assigned yet (see section 2.3), both LEDs remain off.

The integrated thermostats do not start operating until the device has a role assigned.

When the device adopts a role, it will start performing the thermostat actions as if a

restart had just taken place. Moreover, on the first execution, the thermostat actions

that may apply after an ETS download will also take place.

The following sections describe the master and slave operating modes.

2.2.1 MASTER

The master handles the climate control by sending the control orders and states

(communication objects) when required.

While the device is operating as a master, the master LED indicator is on.

2.2.1.1 COMMUNICATION OBJECT NOTIFICATIONS

Periodically (time set by parameter), the master device sends a ‘1’ through the master

notification communication object, and afterwards its internal checksum value.

If a master device receives any value through the master notification object,

automatically switches to slave mode (and sends the corresponding slave notification).

MCC

http://www.zennio.com Technical Support: http://support.zennio.com

Figure 2 Master notification.

In order to avoid message collision, if a master notification is received (from another

device) no later than 100 ms after sending a master notification, the device switches to

the “undefined” state and it will start the role selection process (see section 2.3).

2.2.1.2 SLAVE NOTIFICATION RECEPTION

The master expects to receive periodically (through the slave notification object) a

confirmation that the slave device is operating properly. If it doesn’t receive any value

through this object during two times and a half the slave notification time (set by

parameter), the ‘missing slave’LED indicator will turn on. And once any value is

received through the communication object, the LED will turn off.

Figure 3 No-slave detection by the master.

Master

Master Notif.

Checksum

Master Notif.

Checksum

Master Notif.

Checksum

Master Notif.

Slave Notif.

Checksum

master

Master

Slave Notif.

slave

Slave Notif.

2.5 x t

slave

LED on

Table des matières

Autres manuels Zennio Contrôleurs

Zennio

Zennio DIMinBOX 2CH ZDI-DB2C Manuel utilisateur

Zennio

Zennio FANinBOX 110V 1CH Mode d’emploi

Zennio

Zennio ZIO-IB24 Manuel utilisateur

Zennio

Zennio MAXinBOX Manuel utilisateur

Zennio

Zennio ZN1DI-RGBX4 Manuel utilisateur

Zennio

Zennio AudioInRoom ZMU-AUIR Manuel utilisateur

Zennio

Zennio ACTinBOX MAX6 Manuel utilisateur

Zennio

Zennio ZCL-FC010F Mode d’emploi

Zennio

Zennio HeatingBOX 230V 4X Mode d’emploi

Zennio

Zennio MINiBOX 45 v3 Mode d’emploi

Zennio

Zennio MAXinBOX FC 0-10V VALVE Manuel utilisateur

Zennio

Zennio MAXinBOX 24 ZIO-MB24 Manuel utilisateur

Zennio

Zennio MAXinBOX 16 Mode d’emploi

Zennio

Zennio MINiBOX 40 v3 Manuel utilisateur

Zennio

Zennio MINiBOX 25 Mode d’emploi

Zennio

Zennio MAXinBOX 16 Plus Mode d’emploi

Zennio

Zennio MINiBOX 45v2 Manuel utilisateur

Zennio

Zennio MAXinBOX 66 Mode d’emploi

Zennio

Zennio ZCL-8HT230 Mode d’emploi

Zennio

Zennio MAXinBOX FANCOIL 2CH2P Manuel utilisateur

Zennio

Zennio MAXinBOX FC 0-10V FAN Mode d’emploi

Zennio

Zennio MINiBOX 20 Manuel utilisateur

Zennio

Zennio MAXinBOX SHUTTER 8CH v3 Mode d’emploi

Zennio

Zennio Tecla 55 X Sign Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur