Zennio FANinBOX 110V 1CH Mode d’emploi

FANinBOX 110V 1CH

3-speed ceiling fan controler @110VAC

ZCLFB110C1 TECHNICAL DOCUMENTATION

FEATURES

•External 110V 50/60Hz power supply.

•Up to 3 speeds control for ceiling fans.

•Manual control through push button and LED indicator.

•10 logic functions.

•Total data saving on KNX bus failure.

•Integrated KNX BCU.

•Dimensions 67 x 90 x 35mm (2 DIN units).

•DIN rail mounting (EN 50022), through pressure.

•Conformity with the CE directives (CE-mark on the right side).

1. Power supply input

2. Fan output

3. Speed control buttons

4. Speed indicator LEDs

5. Programming/Test button

6. Programming/Test LED

7. KNX Connector

Figure 1: FANinBOX 110V 1CH

Programming/Test button: short press to set programming mode. If this button is held while plugging the device into the KNX bus, it enters the safe

mode. If this button is held for more than 3 seconds, the device enters the test mode.

Programming/Test LED: programming mode indicator (red). When the device enters the safe mode, it blinks (red) every half second. The manual mode

is indicated by the green color. During the start-up (reset or after KNX bus failure) and if the device is not in safe mode, it starts a blue blinking sequence.

GENERAL SPECIFICATIONS

CONCEPT

DESCRIPTION

Type of device

Electric operation control device

KNX supply

Voltage (typical)

29VDC SELV

Voltage range

21..31VDC

Maximum

consumption

Voltage

29VDC (typical)

3.9

113.1

24VDC¹

240

Connection type

Typical TP1 bus connector for 0.80mm Ø rigid cable

External power supply

110VAC 50/60Hz

Operation temperature

0°C .. +55°C

Storage temperature

-20°C .. +55°C

Operation humidity

5 .. 95%

Storage humidity

5 .. 95%

Complementary characteristics

Class B

Protection class / Overvoltage category

II / III (4000V)

Operation type

Continuous operation

Device action type

Type 1

Electrical stress period

Long

Degree of protection / Pollution degree

IP20 / 2 (clean environment)

Installation

Independent device to be mounted inside electrical panels with DIN rail (EN

50022)

Minimum clearances

Not required

Response on KNX bus failure

Data saving according to parameterization

Response on KNX bus restart

Data recovery according to parameterization

Operation indicator

The programming LED indicates programming mode (red) and test mode

(green). The output LEDs indicate its status (fixed = full speed; fast/slow

flashing = high/slow speed; off = stoped)

Weight

109g

PCB CTI index

175V

Housing material / Ball pressure test temperature

PC FR V0 halogen free / 75ºC (housing) - 125ºC (connectors)

¹ Maximum consumption in the worst case scenario (KNX Fan-In model)

SAFETY INSTRUCTIONS

•Installation should only be performed by qualified professionals according to the laws and regulations applicable in each country.

•Do not connect the mains voltage nor any other external voltage to any point of the KNX bus; it would represent a risk for the entire

KNX system. The facility must have enough insulation between the mains (or auxiliary) voltage and the KNX bus or the wires of other

accessories, in case of being installed.

•The facility must be equipped with a device that ensures the omnipolar sectioning. Installation of a 10A mini-circuit-breaker is

recommended. To prevent accidents, it must remain open in case of manipulation of the device.

•Once the device is installed (in the panel or box), it must not be accessible from outside.

•Keep the device away from water (condensation over the device included) and do not cover it with clothes, paper or any other material

while in use.

•The WEEE logo means that this device contains electronic parts and it must be properly disposed of by following the instructions at

http://zennio.com/weee-regulation.

OUTPUTS SPECIFICATIONS AND CONNECTIONS

CONCEPT

DESCRIPTION

Number of outputs

Output type

Relays based control device

Maximum recommended load per output

100W

Minimum load per output

30W

Short-circuit protection

Overload protection

Connection method

Screw terminal block

Cable cross-section

0.5-2,5mm² (IEC) / 26-12AWG (UL)

Outputs per common

Maximum response time

15ms

Mechanical lifetime (min. cycles)

3 000 000

Electrical lifetime (min. cycles)1

100000 @ 8A / 25000 @ 16A (VAC)

¹ Lifetime values could change depending on the load type.

EXTERNAL POWER SUPPLY SPECIFICATIONS AND CONNECTIONS

CONCEPT

DESCRIPTION

Voltage

110VAC

Connection method

Screw terminal block

Cable cross-section

0.5-2,5mm² (IEC) / 26-12AWG (UL)

⚠In order to ensure the expected

status of the relays, please check

that the device is connected to the

KNX bus before energizing the

power circuit.

⚠Use for ceiling fans. Do not

use other load to avoid

damages.

WIRINGDIAGRAMS

Figure 2: Wiring diagram of a fan

Figure 3: Mounting FANinBOX 110V 1CH on

DIN rail

Attaching FANinBOX 110V 1CH to DIN rail:

Removing FANinBOX 110V 1CH from DIN rail:

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Zennio Contrôleurs

Zennio

Zennio AudioInRoom ZMU-AUIR Manuel utilisateur

Zennio

Zennio MINiBOX 25 Mode d’emploi

Zennio

Zennio ZIO-IB24 Manuel utilisateur

Zennio

Zennio MAXinBOX SHUTTER 8CH v3 Mode d’emploi

Zennio

Zennio MAXinBOX 8 Mode d’emploi

Zennio

Zennio inBOX 24 v2 Manuel utilisateur

Zennio

Zennio ZoningBOX 6 Mode d’emploi

Zennio

Zennio MAXinBOX Hospitality ZCL-HP126 Manuel utilisateur

Zennio

Zennio MAXinBOX 66 Manuel utilisateur

Zennio

Zennio HeatingBOX 24V 4X Manuel utilisateur

Zennio

Zennio MAXinBOX 16 Plus Mode d’emploi

Zennio

Zennio MAXinBOX SHUTTER 4CH Manuel utilisateur

Zennio

Zennio MINiBOX 25 v3 Mode d’emploi

Zennio

Zennio ZoningBOX 6 Mode d’emploi

Zennio

Zennio MAXinBOX Manuel utilisateur

Zennio

Zennio MINiBOX 0-10V X3 Manuel utilisateur

Zennio

Zennio AudioInRoom Manuel utilisateur

Zennio

Zennio MAXinBOX 66 Mode d’emploi

Zennio

Zennio MAXinBOX 66 Manuel utilisateur

Zennio

Zennio ACTinBOX MAX6 Manuel utilisateur

Zennio

Zennio MAXinBOX FC 0-10V VALVE Manuel utilisateur

Zennio

Zennio MAXinBOX 24 Mode d’emploi

Zennio

Zennio IRSC Plus Manuel utilisateur

Zennio

Zennio MAXinBOX 66 v2 Mode d’emploi

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur