Zeiss LSM 700 Manuel utilisateur

071

0EWIV7GERRMRK1MGVSWGSTI

0717SJX[EVI>)2

.ERYEV]

1UICK'UIDE

Microscopy from Carl Zeiss

01/2013 1

Contents

Page

Contents ................................................................................................................................. 1

Introduction............................................................................................................................ 1

Starting the System ............................................................................................................... 2

Introduction to ZEN – Efficient Navigation .......................................................................... 5

Setting up the microscope................................................................................................... 10

Configuring the beam path and lasers............................................................................... 13

Scanning an image............................................................................................................... 19

Storing and exporting image data ..................................................................................... 24

Switching off the system..................................................................................................... 25

Introduction

This LSM 700 Quick Guide describes the basic operation of the LSM 700 Laser Scanning Microscope with

the ZEN 2012 software.

The purpose of this document is to guide the user to get started with the system as quick as possible in

order to obtain some first images from his samples.

This Quick Guide does NOT replace the detailed information available in the full user manual or in the

manual of the respective microscopes (Axio Imager, Axio Observer).

Also, this Quick Guide is written for a user who is familiar with the basics of Laser Scanning Microscopy.

For your safety!

Observe the following instructions:

The LSM 700 laser scanning microscope, including its original accessories and

compatible accessories from other manufacturers, may only be used for the purposes

and microscopy techniques described in this manual (intended use).

In the Operating Manual, read the chapter Safety Instructions carefully before

starting operation.

Follow the safety instructions described in the Operating Manual of the microscope

and X-Cite 120 lamp / HBO 100 mercury lamp.

2 01/2013

Starting the System

Switching on the LSM 700 system

xTurn on the LSM 700 system via the switch-

operated multipoint connectors (power strips 1

and 2) on the system. This switches on all

system components except attached scanning

stages, the microscope and its illumination

(HBO 100, XBO 75 or HXP 120).

xIf using the Axio Observer microscope stand,

push the power button at the left hand side

first to switch on the microscope.

xTurn the key switch (Fig. 1/1) of the electronics

and laser module to the right to start the laser.

The yellow LED in return turns on. If this is not

the case, check the power switch (Fig. 2/2) on

the back of the laser module.

xOn the back of the system there is a plastic

screw (Fig. 2/1). This is a laser interlock which

can be used for coupling the laser module e.g.

to doors. If this screw is unscrewed the lasers

will not turn on!

Switching on the HXP 120 or the HBO 100

or the XBO 75 lamps

xSwitch on the main switch of the HXP 120 /

HBO 100 / XBO 75 lamps for reflected light

illumination via the power supply as described

in the respective operating manual.

Switching on the scanning stage

xIf attached, switch on the scanning stage via the

controller.

Fig. 1 Electronics and laser module

Fig. 2 Electronics and laser module

01/2013 3

Starting the ZEN software

xDouble click the ZEN 2012 icon on the WINDOWS desktop to start the Carl Zeiss LSM

software.

The ZEN Main Application window and the LSM 700 Startup window appear on the

screen (Fig. 3).

In the small startup window, choose either to start the system online (Start System hardware for

acquiring new images) or in Image Processing mode to edit already existing images. Toggle the little

symbol to view the Boot Status display and get the additional Offline/Demo button option:

Choosing Start System initializes the whole microscope system and activates the entire software

package for new image acquisition and analysis.

The Image Processing mode ignores all hardware and activates only data handling and image

processing functionality for already acquired images.

The Offline/Demo mode reads the current hardware database but does not activate the system

hardware for use. Instead, it simulates the system hardware for training purposes.

Upon clicking the Start System button, the Image Processing button changes to a Cancel

button. Click Cancel to interrupt/stop Startup of the system.

After startup, the ZEN Main Application window (Fig. 4 and Fig. 5) opens. To benefit from all of ZEN's

features, run the window in its full screen mode.

Fig. 3 ZEN Main Application window at Startup (a) and the LSM 700 Startup window (b and c)

4 01/2013

Fig. 4 ZEN Main Application window after startup with empty image container

Fig. 5 ZEN Main Application window after startup with several images loaded

01/2013 5

Introduction to ZEN – Efficient Navigation

The ZEN 2012 Interface is clearly structured and follows the typical workflow of the experiments

performed with confocal microscopy systems:

On the Left Tool Area (Fig. 4/D) the user finds the tools for sample observation, image acquisition,

image processing and system maintenance, easily accessible via four Main Tabs (Fig. 5/1). All functions

needed to control the microscope can be found on the Locate tab, to acquire images use the

Acquisition Tools (Fig. 5/3and 4). Arranged from top to bottom they follow the logic of the

experimental workflow. The area for viewing and interacting with images is centered in the middle of the

Main Application window: the Center Screen Area. Each displayed image can be displayed and/or

analyzed with many view options available through view tabs which can be found on the left side of the

image. According to the chosen view tab, the required view controls appear in View Control Tabs below

each image. File management and data handling tools are found in the Right Tool Area (see Fig. 4 and

Fig. 5).

Color and brightness of the interface have been carefully adjusted to the typical light conditions of the

imaging laboratory, guaranteeing optimal display contrast and minimal stray light for high-sensitivity

detection experiments. The ZEN software is optimized for a 30" TFT monitor but can also be used with

dual-20" TFT setups.

A focus in the development of ZEN 2012 was to fulfill the needs of both basic users and microscopy

specialists. Both types of users will appreciate the set of intuitive tools designed to make the use of a

confocal microscope from Carl Zeiss easy and fast.

The Show all concept ensures that tool panels are never more complex than needed. With Show all de-

activated, the most commonly used tools are displayed. For each tool, the user can activate Show all

mode to display and use additional functionality (Fig. 6).

Fig. 6 Show all mode

6 01/2013

More features of ZEN 2012 include:

The user can add more columns for tools to the Left Tool Area or detach individual tools to

position them anywhere on the monitor. To add a column, drag a tool group by the title bar (e.g.,

Online Acquisition) to the right and a new tool column automatically opens. Alternatively use the

context menu "move toolgroup to next column". To detach a tool, click on the little icon on the

very right end of the blue tool header bar (Fig. 7).

Another unique feature in Imaging software is the scalable ZEN interface. This Workspace Zoom

allows adjustment of the ZEN 2012 window size and fonts to the situational needs or your

personal preferences (Fig. 7).

Setting up conventional confocal software for a specific experiment can take a long time and is

often tedious to repeat. With ZEN these adjustments have to be done only once – and may be

restored with just two clicks of the mouse. For each type of experiment one can now set-up and

save the suitable Workspace Layout. These configurations can also be shared between users.

For most controls, buttons and sliders, a tool tip is available. When the mouse pointer is kept over

the button, a small pop-up window will display which function is covered by this tool/button.

These are just some of the most important features of the ZEN interface. For a more detailed description

of the functionality for the ZEN 2012 software, please refer to the User Manual that is provided with

your system.

Fig. 7 ZEN Window Layout configuration

01/2013 7

Setting up a new image document and saving your data

To create a new image document in an empty image container, click the Snap or the

Set Exposure button. For an empty image document press the New button.

The new document is immediately presented in the Images andDocuments panel of the Right Tool

Area. Remember, an unsaved 2D image in the active image tab will be over-written by a new scan. Multi-

dimensional scans or saved images will never be over-written and a new scan will then automatically

create a new image document.

Acquired data is not automatically saved to disc. Make sure you save your data appropriately and back it

up regularly. The ZEN software will ask you if you want to save your unsaved images in case you try to

close the application with unsaved images still open.

There is no image database any more like in the earlier Zeiss LSM software versions.

Fig. 8 New image document in the Open Images Areas

8 01/2013

Advanced data browsing is available through the ZEN File Browser (Ctrl + F or from the File menu). The

File Browser can be used like the WINDOWS program file browser. Images can be opened by double-click

and image acquisition parameters are displayed with the thumbnails (Fig. 9). For more information on

data browsing please refer to the detailed operating manual.

Fig. 9 File Browser

Autres manuels pour LSM 700

Table des matières

Autres manuels Zeiss Microscope

Zeiss

Zeiss Standard 25 ICS Manuel utilisateur

Zeiss

Zeiss LSM 880 Manuel utilisateur

Zeiss

Zeiss Cell Observer SD Manuel utilisateur

Zeiss

Zeiss LSM800-02 Manuel de l'opérateur

Zeiss

Zeiss AxioImager A1 Instructions de montage

Zeiss

Zeiss Stemi 305 cam Manuel utilisateur

Zeiss

Zeiss opmi lumera 700 Manuel utilisateur

Zeiss

Zeiss LSM 700 Manuel utilisateur

Zeiss

Zeiss ELYRA Manuel utilisateur

Zeiss

Zeiss Stemi DV4 Manuel utilisateur

Zeiss

Zeiss Axiolab 5 Manuel utilisateur

Zeiss

Zeiss Primo Star Manuel utilisateur

Zeiss

Zeiss Axio Scope.A1 Manuel utilisateur

Zeiss

Zeiss Axio Imager 2 Manuel utilisateur

Zeiss

Zeiss Stemi 305 Manuel utilisateur

Zeiss

Zeiss Stemi 508 Manuel utilisateur

Zeiss

Zeiss Definite Focus.2 Manuel utilisateur

Zeiss

Zeiss Axioplan Universal microscope Manuel utilisateur

Zeiss

Zeiss Primostar 3 Manuel utilisateur

Zeiss

Zeiss JENAVAL Manuel utilisateur

Zeiss

Zeiss VISU 200 Manuel utilisateur

Zeiss

Zeiss Corona extreme Manuel utilisateur

Zeiss

Zeiss HBO 100 Manuel utilisateur

Zeiss

Zeiss SV8 Manuel utilisateur

Manuels Microscope populaires d'autres marques

Thermo Scientific

Thermo Scientific Nicolet iN10 Mode d’emploi

National

National DC3-163 Manuel utilisateur

KERN Optics

KERN Optics OPE-1 Manuel utilisateur

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manuel utilisateur

Prior

Prior Lux POL Manuel utilisateur

Opitec

Opitec Smartscoop 115615 Manuel utilisateur

KERN

KERN OPO-1 Manuel utilisateur

Topcon

Topcon SP-1P Manuel utilisateur

Motic

Motic PA43 Manuel utilisateur

Leica

Leica DVM5000 Guide de l'utilisateur

MshOt

MshOt MZ62 Manuel utilisateur

KERN Optics

KERN Optics OZR-5 Manuel utilisateur

VWR

VWR VisiScope 384 Series Manuel utilisateur

Nikon

Nikon ECLIPSE E200 POL Manuel utilisateur

Leica

Leica DI C800 Manuel

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

Olympus

Olympus SZ61 Manuel utilisateur