Yolink SpeakerHub YS1604-UC Manuel utilisateur
YoLink SpeakerHub
YS1604-UC
Set-up & User Guide
Rev 1.0
January 20, 2022 If your SpeakerHub is already online after using the QSG, please
proceed to page 22
Table of Contents
PART TOPIC PAGE
A Thank you! 1
B Introduction 2
C Before You Begin 4
DWhat’s in the Box? 5
E Get to Know Your SpeakerHub 6
F Install the YoLink App 7
G Open the App 8
H Add Your SpeakerHub to the App 9
I Power Up the SpeakerHub 11
J Mobile Device Settings 12
K Connect Hub to WiFi 14
L Introduction to the App 22
M SpeakerHub Device Settings 23
N Advanced Settings 29
O Firmware Updates 31
P Factory Reset 32
Q FCC Statement 33
R CE Mark Warning 34
S Warranty 35
T Warning 35
U Contact Us / Support 36
Thank you for purchasing YoLink products!
Whether you are adding additional hubs to expand
your system's range or if this is your first YoLink
system, we appreciate you trusting YoLink for your
smart home & automation needs. Your 100%
satisfaction is our goal. If you experience any
problems with your installation, with our products
or if you have any questions that this manual does
not answer, please contact us right away. See the
Contact Us section for more info.
Thank you!
Eric, Queenie, John, Clair, James
Customer Support Team
Thank you!
A
Introduction
B
YoLink Hubs are the gateway to the internet for
your YoLink devices. As opposed to many smart
home systems, the individual devices are
not
on
your network or WiFI and are not directly
connected to the internet. Instead, your devices
communicate with the Hub, which connects to the
internet, the cloud server and the app.
Your SpeakerHub can only connect to the internet
via a 2.4 GHz band provided by your WiFi network
(5 GHz band is not supported at this time). Like most
IoT and home automation devices, your SpeakerHub
connects only to the 2.4 GHz WiFi band. Nearly all
residential WiFi routers have a 5
and
a 2.4 GHz
band. But your router may or may not display SSIDs
for
both
bands or they may both have the
same
name
. If you know which SSID is your 2.4 GHz band,
this is the one your Hub will connect to.
With some exceptions, your router and the
SpeakerHub will connect automatically via 2.4 GHz.
Some routers may attempt to connect your Hub to 5
GHz. Additional support may be needed, for
example, changing your router settings.
“5 GHz” should not be confused with “5G”
cell phone service
🤔
Multi-step authentication networks, such as
hotels and airports, are not compatible!
User Guide Conventions
To assure your satisfaction with your purchase, please
read this user guide we have prepared just for you.
The following icons are used to convey specific types of
information:
Very important information (can save you time!)
🤔
🧰
12
Good to know info but may not apply to you
Troubleshooting tips
Mostly unimportant (it’s ok to breeze past it!)
Your system may have more than one Hub, due to
the number of devices (one Hub can support at
least 300 devices), and/or the physical size of your
home or building(s) and/or property. YoLink's
unique LoRa®-based long-range/low-power
system offers industry-leading range - up to 1/4
mile reach, open air!
You can have multiple hubs. If you already have
our original Hub, you do not have to replace it, if it
is functional. Additional hubs will only expand the
coverage area of your YoLink system.
Introduction, Continued
BBefore You Begin
C
Do not allow your SpeakerHub to get wet
…or eat after midnight
🤔
Find a suitable place for your SpeakerHub to live.
SpeakerHub wants to be indoors, clean and dry.
SpeakerHub is not designed for wall-mounting.
Place your SpeakerHub at a location where you can
hear the speaker clearly, at a moderate volume
level.
Avoid placing your SpeakerHub inside a cabinet, or
on or near metal or sources of radio or
electromagnetic energy or interference, such as
radio transmitters, as well as other WiFi equipment.
Do not place your SpeakerHub on or near sources
of heat or intense direct sunlight, such as a space
heater.
An outlet will be required for the power adapter for
your SpeakerHub. Ensure it can have a dedicated
outlet; it will not work if it is unplugged;
SpeakerHub does
not
have an internal battery.
34
A. SpeakerHub
B. USB Cable (“Micro B”)
C. AC Adapter / Power Supply
D. Quick Start Guide
What’s in the Box?
DGet to Know Your SpeakerHub
E
Please take a moment to familiarize yourself with
your new SpeakerHub, in particular the LED
behaviors and SET button functions.
LED Behavior explanations
56
If you are new to YoLink, please install the app on
your phone or tablet, if you have not already.
Otherwise, please proceed to part H.
Scan the appropriate QR code below or find the
“YoLink app” on the appropriate app store.
Open the app and tap Sign up for an account. You
will be required to provide a username and a
password.
Follow the instructions, to set up a new account
Install the YoLink App
FOpen the App
G
Retain your username and password in a secure location
If you encounter an error message attempting to create
an account, disconnect your phone from WiFi, and try
again, connected only to the cellular network
🧰
Apple phone/tablet
iOS 9.0 or higher
Android phone/tablet
4.4 or higher
You will immediately receive an email from
no[email protected] with some helpful
information. Please mark the yosmart.com domain
as safe, to ensure you receive important messages
in the future.
Log in to the app
using your new
username and
password
The app opens to
the Favorite
screen, as shown.
This is where
your favorite
devices will be
shown. You can
organize your
devices by room,
in the Rooms
screen, later.
Tap Add Device
(if shown) or tap
the scanner icon
Scanner icon
78
1
2
3
1
2
3
4
Approve access to your phone’s camera, if
requested.) A viewfinder will be shown on the app.
Hold the phone over the QR code (on the underside
of the hub) so that the code appears in the
viewfinder. If successful, the Add Device screen will
be displayed
Add Your SpeakerHub to the App
H
If you experience difficulties scanning in a new device,
ensure the code is not dirty or smudged, and that the
camera has adequate lighting. If you are still unable to scan
a device, please make a note of the serial number for our
customer support staff. This is the number right below the
QR code, a long number preceded by “S/N:”
🧰
You can change the
device name and assign it
to a room later. Ensure
that the Favorite icon is
selected as shown (red
heart). Tap Bind device
If successful, the screen
will appear as shown. Tap
Done (do not tap “set up
WiFi connection” at this
time)
910
2
1
3
4
Connect the supplied USB cable to the hub and to
the power adapter as shown.
Plug in the adapter. Observe the green power (PWR)
LED is blinking
iOS phones only: if prompted, enable Local Network
Access. Search “iOS location services” for more
information
Enable Location Services on your phone
iOS:
Go to Settings, tap Privacy, tap Location Services
Ensure Location Services is on/enabled.
Scroll down to and tap the YoLink app
Select While Using the App
Enable Precise Location
Android:
Go to Settings, tap Location.
Ensure Location is On.
Tap App Permissions. Scroll down to and
tap the YoLink app, then set permission to
Allowed Only While in Use
Power up the SpeakerHub
IMobile Device Settings
J
11 12
1
1
2
In your phone, open WiFi settings (Settings, WiFi)
Identify your 2.4 GHz network, if possible. If there is
only one SSID (network ID) you recognize, you will
use that one
If your SSID is hidden, you must manually log into it
on your phone, by selecting “Other...” in Other
Networks or Choose a Network
Select the appropriate network and log-in, if needed
From the Rooms or Favorites screen, tap on the
SpeakerHub icon, as shown in the left figure
Mobile Device Settings, Continued
JConnect Hub to WiFi
K
1
13 14
1
2
3
4
2Tap on the WiFi icon as shown on the right figure
The Set WiFi screen appears as shown.
Connect Hub to WiFi, Continued
K
As directed in the app, press the hub’s SET
button for
more
than 10 seconds or until the
WiFi LED flashes rapidly. (The LED will start
flashing
slowly
at around 5 seconds; keep
pressing)
Go to your phone’s WiFi settings and log into the
SpeakerHub hotspot. The hotspot can be
identified by the number that starts with
“YS_1604”
Connect Hub to WiFi, Continued
K
Please review the instructions on the screen. After
pressing the SET button the SpeakerHub, you will
then log into the SpeakerHub’s hotspot. This will
need to be done with no delays between steps,
otherwise the Hub will exit AP pairing mode.
4
5
6
15 16
3Do not change SSID and password at this time.
Tap Set up WiFi via wireless hotspot
The “Set up WiFi successfully” message should
appear on the screen as shown. Tap Done
Connect Hub to WiFi, Continued
K
The SpeakerHub’s blue internet status LED
should be on, indicating an internet connection
is established
Connect Hub to WiFi, Continued
K
10
11
17 18
Your SpeakerHub may appear offline. Tap the
Refresh icon or swipe down on the screen to
refresh the screen
If your SpeakerHub indicates Online as shown,
you can proceed to part L
12
Return to the app. Check the “Please confirm the
above operation” checkbox
Tap Continue
The WiFi Password Setting screen appears as
shown
In the Choose a WiFi box, please select or enter
your 2.4 GHz SSID (unless it is hidden, it should
appear in the list, when you tap in this area). Enter
your WiFi password, then tap Continue
7
8
9
MyWiFi
If there is a pop-up message on your phone, noting this
network connection does not have internet access, please
approve the connection. Approve “once” or “this time only”
if desired. (This is only a temporary connection)
Autres manuels pour SpeakerHub YS1604-UC
1
Table des matières
Autres manuels Yolink Changer
