YASKAWA DS031 Manuel utilisateur

Yaskawa Electric America, Inc – www.drives.com

02Y00025-0515 Page 1 of 3

Date: 08/28/01

Remote Digital Operator (NEMA 4/12) Option,

Model DS031 & DS033 for GPD 305/J7

Introduction

The remote digital operator kit allows a digital operator to be mounted up to 3 meters from the GPD305/J7. The

kit includes:

1. One remote operator interface attachment

2. One gasket

3. One Digital Operator membrane cover

4. Four screws & nuts

5. Eight rubber washers

6. One RS-232 remote operator interface

7. One cable either 1 meter (DS031) or 3 meter (DS033) in length.

Hardware Installation

WARNING

HAZARDOUS VOLTAGE CAN CAUSE SEVERE INJURY OR DEATH. LOCK ALL POWER

SOURCES DRIVE IN “OFF” POSITION.

1. Disconnect all electrical power to Drive.

2. Verify power has been disconnected by using a voltmeter to check for voltage at incoming power terminals

(L1, L2, and L3).

3. Wait for the DC bus capacitors to completely discharge.

4. Remove contents from package. Verify that the above mentioned parts are included:

5. install the RS-232 remote interface. First, remove the screw on the front cover of the drive. Next, remove the

small square cover located above the control terminals to access CN1. Install the RS-232 remote interface by

positioning the interface directly above the CN2 connector. Press down on interface until all three tabs snap

into place.

6. Re-attach the front cover and tighten the screw down.

Yaskawa Electric America, Inc – www.drives.com

02Y00025-0515 Page 2 of 3

Date: 08/28/01

Remote Digital Operator (NEMA 4/12) Option,

Model DS031 & DS033 for GPD 305/J7

Flush Mounting. Mount the Digital Operator as follows.

1. Cut the Remote Operator mounting panel as shown in Fig. 1.1

Figure 1.1 (Dimensions in Inches, not actual size)

2. Install the Remote Operator on the front side of the panel. Use four stainless screws and four rubber

washers (one rubber washer per screw). See Figure 1.2

FIGURE 1.2

Yaskawa Electric America, Inc – www.drives.com

02Y00025-0515 Page 3 of 3

Date: 08/28/01

Remote Digital Operator (NEMA 4/12) Option,

Model DS031 & DS033 for GPD 305/J7

Surface Mounting. Mount the Digital Operator as follows.

1. Cut the Remote Operator mounting panel as shown in Fig. 2.1

Figure 2.1

(Dimensions in Inches, not actual size)

2. Apply the gasket to the front side of the digital operator. Install the remote operator from the rear side of panel.

Insert the screws through the front side of the panel and then mount the washers and nuts to the rear side of the

panel. Tighten screws gradually from the front side of panel. Refer to figure 2.2 for further installation directions.

3. Connect one end of the cable to the CN1 connector on

the drive and the other end of the cable to the RJ-45

receptacle on the back of the Digital Operator.

This completes the installation process.

Figure 2.1 Remote Operator Installation

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels YASKAWA Contrôleurs

YASKAWA

YASKAWA YRC1000 Manuel utilisateur

YASKAWA

YASKAWA SGD7S-xxxDA0 series Manuel utilisateur

YASKAWA

YASKAWA MP2600iec Manuel utilisateur

YASKAWA

YASKAWA SI-M3/V Manuel utilisateur

YASKAWA

YASKAWA Lift Inverter L1000V Manuel utilisateur

YASKAWA

YASKAWA Varispeed G7 Manuel utilisateur

YASKAWA

YASKAWA MP23xxxiec Series Manuel utilisateur

YASKAWA

YASKAWA J1000 CIMR-JC series Manuel utilisateur

YASKAWA

YASKAWA Motoman DX200 Manuel utilisateur

YASKAWA

YASKAWA A1000 Series Manuel utilisateur

YASKAWA

YASKAWA MP2300S Manuel utilisateur

YASKAWA

YASKAWA L1000A Series Manuel utilisateur

YASKAWA

YASKAWA Motoman DX200 Manuel utilisateur

YASKAWA

YASKAWA iC9200 Series Manuel utilisateur

YASKAWA

YASKAWA motoman NX100 Manuel utilisateur

YASKAWA

YASKAWA Motoman DX200 Manuel utilisateur

YASKAWA

YASKAWA PG-X3 Manuel utilisateur

YASKAWA

YASKAWA Varispeed-616GII Manuel utilisateur

YASKAWA

YASKAWA MOTOMAN FS100 Manuel utilisateur

YASKAWA

YASKAWA JEPMC-YVD3001-E Manuel utilisateur

YASKAWA

YASKAWA MOTOMAN-NX100 Manuel utilisateur

YASKAWA

YASKAWA SI-P3V Manuel utilisateur

YASKAWA

YASKAWA iQpump Guide de configuration

YASKAWA

YASKAWA SGM series Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur

3M MicroTouch EX113 Manuel utilisateur