Yamaha WABASH 2019 Manuel utilisateur

2019

ASSEMBLY MANUAL

WABASH

PW70WL

PW70WM

PW70WS

LIT-15666-00-05 X1M-28107-14

FOREWORD

This Assembly Manual contains the information required for the correct assembly of this Yamaha bicycle prior

to delivery to the customer. Since some external parts of the bicycle have been removed at the Yamaha fac-

tory for the convenience of packing, assembly by the Yamaha dealer is required. No adjustment of the power

unit mechanism, which plays the most important part in riding, is necessary because it has been adjusted at

the factory before shipping. It should be noted that the assembled bicycle should be thoroughly cleaned,

checked, and adjusted prior to delivery to the customer.

IMPORTANT

The service specifications given in this assembly manual are based on the model as manufactured. Yamaha

Motor Company, Ltd. is continually striving to improve all of its models. Modifications and significant changes

in specifications or procedures will be forwarded to all authorized Yamaha dealers and will appear in future

editions of this manual where applicable.

The procedures below are described in the order that the procedures are carried out correctly and completely.

Failure to do so can result in poor performance and possible harm to the bicycle and/or rider.

Particularly important information is distinguished in this manual by the following notations.

Follow the instructions in the Dealer Warranty Handbook, Procedure Section.

This is the safety alert symbol. It is used to alert you to potential personal

injury hazards. Obey all safety messages that follow this symbol to avoid pos-

sible injury or death.

A WARNING indicates a hazardous situation which, if not avoided, could result

in death or serious injury.

A NOTICE indicates special precautions that must be taken to avoid damage to

the bicycle or other property.

A TIP provides key information to make procedures easier or clearer.

WARNING

NOTICE

TIP

PW70WL/PW70WM/PW70WS

ASSEMBLY MANUAL

First edition, January 2019

Any reproduction or unauthorized use

without the written permission of

Yamaha Motor Corporation, U.S.A.

is expressly prohibited.

Printed in U.S.A.

P/N LIT-15666-00-05

PARTS LOCATION

– 1 –

PARTS LOCATION

1. Part box 1

2. Front wheel

8Do not use a cutter, scissors, or other sharp object to open the part boxes; otherwise, the included

parts could be damaged.

8Wear suitable protective gear such as gloves when handling and opening the part boxes.

NOTICE

INCLUDED PARTS

– 2 –

INCLUDED PARTS

The parts listed as follows are included*. Check the parts and their quantities before starting assembly.

Part box 1 details

Part box 2 details

Part box 3 details

* The form of the package is subject to change without notice.

No. Part names Q’ty Remarks

1Front wheel 1

2Part box 1 1

3Part box 2 12in part box 1

4Part box 3 12in part box 1

5Saddle and seat post assembly 1

6Front axle 1

7Pedals 21 each for left and right

8Bell 1

9Front reflector 1

0Rear reflector 1

qOwner’s manual 1

wButton cell battery 1qin owner’s manual pouch

Standard CR2032

eBattery charger 1

INCLUDED PARTS

– 3 –

INSTALLING THE INCLUDED PARTS

– 4 –

INSTALLING THE INCLUDED

PARTS

TIP

8Insert the key into the battery lock, turn it to

release the battery lock, and then remove the

battery pack.

8Charge the battery pack following the instruc-

tions in the owner’s manual before starting

installation.

8The letters inside the parts list boxes in the

assembly procedures indicate the following:

A: Part in part box 1

B: Part in part box 2

1. Installing the front wheel and fork end

Remove the spacer bfrom the front disc cali-

per a.

Give the removed spacer bto the customer,

explaining how it is used.

Align the holes in the front wheel 1with the

holes in the fork end and install the front wheel

Install it in such a way that the disc rotor cdoes

not touch the disc pad.

Install the front axle 2to the fork end holes

from the left side of the bicycle.

Tighten the bolts and nuts to the specified

torques. Failure to tighten the bolts and nuts to

the specified torques could prevent proper

operation of the bicycle and make it unsafe to

operate.

WARNING

1Front wheel 1

2Front axle 1 B

INSTALLING THE INCLUDED PARTS

– 5 –

Move the lever dof the front axle 2to “OPEN”

facing the notch e.

With the lever dcaught in the notch e, turn

and tighten until there is a little resistance in the

lever.

Free the lever d.

Determine the position to secure the lever d

and fasten it at “CLOSE”.

TIP

If the lever dof the front axle 2is too hard and

cannot be lowered, or if it is too loose and cannot

be lowered for it to be locked, turn the lever d

again to loosen or tighten it, adjusting so that it can

be fastened securely.

2. Installing the handlebar stem

Position the handlebar stem ain a straight line

with the front wheel.

Tighten the bolts band c, in that order, to the

specified torques.

8Position the lever when it cannot touch

obstacles while the bicycle is moving. If not,

the lever could be unlocked unexpectedly,

causing the front wheel to come off, result-

ing in an accident with severe injury or

death.

8Fasten the lever dat position where the tip

does not touch other parts when the lever

dis lowered.

8Fasten the lever dfacing backward from

the direction of travel in such a way that it

cannot easily touch obstacles that might be

encountered while riding.

WARNING

Tightening torque

6 N·m (0.6 kgf·m, 4.4 lb·ft)

Tightening torque

2.5 N·m (0.25 kgf·m, 1.8 lb·ft)

INSTALLING THE INCLUDED PARTS

– 6 –

3. Installing the handlebar

Install the handlebar aso that the knurled part

bis at the center of the handlebar holder c,

then tighten the 4 handlebar holder cbolts d

to the specified torque.

TIP

8Install the handlebar awith the upper surface

ehorizontal.

8Make sure that the upper surface gof the

brake lever bracket fis parallel with the center

line iof the handlebar stem h.

TIP

8Tighten bolts devenly in stages, in the order

shown in the illustration.

8Tighten in such a way that the gaps jabove

and below the handlebar holder care equal.

4. Installing the display unit’s button cell bat-

tery

Loosen the bolts aand remove the display unit

bfrom the bracket c.

Tightening torque

6 N·m (0.6 kgf·m, 4.4 lb·ft)

The handlebar ashould not touch the frame

when it is turned fully to the left or right.

NOTICE

egf

Tightening torque

2.0 N·m (0.20 kgf·m, 1.5 lb·ft)

INSTALLING THE INCLUDED PARTS

– 7 –

Turn the button cell battery cover don the back

of the display unit bin direction e, remove it,

then install the button cell battery 1.

Mount the button cell battery cover d, then turn

it in direction funtil it locks.

After installing the button cell battery, install the

display unit onto the bracket following the

removal procedure in reverse order.

Peel off the protective film after installing.

5. Installing the display unit

Pass the display of the display unit afrom

behind through the gap above the intersection

of the front and rear brake hoses and shift wire.

As shown in the illustration, install the bracket

part of the display unit ato the side of the han-

dlebar holder band tighten the bolts cto the

specified torque.

6. Installing the headlight

Install the headlight ato the bracket bof the

display unit, then tighten the bolt cto the spec-

ified torque.

TIP

Install in such a way that the headlight points down-

ward from horizontal and shines on the road

approximately 33 ft. (10 m) ahead.

1Button cell battery 1 B

8Install the button cell battery with the plus

(+) mark facing upward.

8Check that the O-ring gis properly

installed.

NOTICE

Tightening torque

3.8 N·m (0.38 kgf·m, 2.8 lb·ft)

Tightening torque

7 N·m (0.7 kgf·m, 5.2 lb·ft)

INSTALLING THE INCLUDED PARTS

– 8 –

7. Installing the front reflector

Install the front reflector 1in the position a

shown in the illustration, then tighten it together

with the stay 2and screw 3.

TIP

Adjust so that the front reflector 1faces straight

ahead, then tighten the screw.

8. Installing the bell

Install the bell 1to the bracket aon the right

side of the bicycle as shown, then tighten it with

the screw 2.

1Front reflector 1 B

2Stay 1 B

3Screw 1 B

1Bell 1 B

2Screw 1 B

Table des matières

Autres manuels Yamaha Scooter

Yamaha

Yamaha BWS 2003 Manuel utilisateur

Yamaha

Yamaha BWS 100 1999 Manuel utilisateur

Yamaha

Yamaha xenter HW125 Manuel utilisateur

Yamaha

Yamaha XP500 Manuel utilisateur

Yamaha

Yamaha XMax YP400RXMAx YP400RA Manuel utilisateur

Yamaha

Yamaha MBK XMAX 2014 Manuel utilisateur

Yamaha

Yamaha SLIDER EW50 NAKED Manuel utilisateur

Yamaha

Yamaha BWS CW50 Manuel utilisateur

Yamaha

Yamaha 2004 YP400 Manuel utilisateur

Yamaha

Yamaha EC-03 Manuel utilisateur

Yamaha

Yamaha Xenter HW151 Manuel utilisateur

Yamaha

Yamaha Vino YJ50RN Manuel utilisateur

Yamaha

Yamaha XCITY VP250 Manuel utilisateur

Yamaha

Yamaha Morphous CP250W Manuel utilisateur

Yamaha

Yamaha QBIX LTV125 Manuel utilisateur

Yamaha

Yamaha YDX TORC PB65YTL Manuel utilisateur

Yamaha

Yamaha ZUMA CW50N Manuel utilisateur

Yamaha

Yamaha Giggle XF50E Manuel utilisateur

Yamaha

Yamaha XMAX YP250R Manuel utilisateur

Yamaha

Yamaha YP125R Manuel utilisateur

Yamaha

Yamaha Fino Manuel utilisateur

Yamaha

Yamaha MAJESTY YP250 Manuel utilisateur

Yamaha

Yamaha CYGNUS.X XC125 Manuel utilisateur

Yamaha

Yamaha JOGR JOGRR CS50 Manuel utilisateur

Manuels Scooter populaires d'autres marques

TEKTRO

TEKTRO CHEETAH Manuel utilisateur

Douglas

Douglas Vespa Sprint Guide d'installation

PLAYTIVE

PLAYTIVE AS-2448 Manuel utilisateur

Ebinger

Ebinger DONKEY XL Manuel utilisateur

Flyer

Flyer Mountain Guide de l'utilisateur

BackCountry eBikes

BackCountry eBikes Storm Manuel utilisateur

equipmed

equipmed FreeRoam II Manuel utilisateur

Yoto

Yoto Lion Manuel utilisateur

WESTHILL BIKES

WESTHILL BIKES LINK Manuel utilisateur

BAnff

BAnff eProdigy series Manuel utilisateur

Winther

Winther 475 Manuel utilisateur

Jetson

Jetson JBZL17 Manuel utilisateur

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Manuel utilisateur

Carrera

Carrera impel Manuel utilisateur

Afikim

Afikim Superlight SL-3 Manuel utilisateur

CareCo

CareCo ZOOM Manuel utilisateur

Douglas

Douglas Vespa G.S. Manuel utilisateur

Gazelle

Gazelle with BOSCH System Manuel utilisateur