Yaesu FTDX101D Manuel utilisateur
1
1. Remove 16 screws and open the bottom case.
SUB
RX-2-UNIT
MAIN
RX-1-UNIT
When installing the filters (XF-128CN/ XF-128S) on the
MAIN side（RX-1-UNIT)
2.Remove 9 cables connected with the RX-1-UNIT.
Coaxial ：7 place
FFC cable：2 place Ｊ01
marking：Red
Ｊ09
marking：
Black
Ｊ10
Marking
：Red
Ｊ12
marking：
Green
Ｊ04
Note: If you find it difficult to remove the coaxial cable, we may
provide you with a special jig. Please contact our Technical
Support desk.
MAIN
RX-1-UNIT
Ｊ11
marking：
none
Ｊ02
marking：none
Ｊ03
marking：
Green
Ｊ05
MAIN
RX-1-UNIT
SUB
RX-2-UNIT
MAIN
RX-1-UNIT
When installing the filters (XF-128CN/ XF-128SN) on the
MAIN side（RX-1-UNIT)
3. Remove 6 Screws and remove the RX-1-UNIT from the
chassis.
MAIN
RX-1-UNIT
XF05
XF-128CN(MAIN) XF06
XF-128SN(MAIN) XF06
XF05
IN
IN
When installing the filters (XF-128CN/ XF-128SN) on the MAIN side（RX-1-UNIT)
4. Insert the filter in the specified position as shown below and solder it.
※Cut the lead of the filters to 2.0 mm or less, after installation.
Please install the filters in correct direction.
If installed in reverse, the performance
quality cannot be guaranteed.
When installing the filters (XF-128CN/ XF-128SN) on the MAIN side（RX-
1-UNIT)
5. Re-assemble the RX-1-UNIT to the chassis. Fix and tighten the srews in
order 1 → 2 → 3 → 4. For the rest screws, there is no specific order.
MAIN
RX-1-UNIT
5.0kgf・cm {0.49Ｎ・m}
Put in the holes in the chassis
①
②
③
④
When installing the filters (XF-128CN/ XF-128SN) on the MAIN
side（RX-1-UNIT)
6. Reconnect the cables to the connector of RX-1-UNIT.
Coaxial ：7 place
FFC cable：2 place
※Pass 4 coaxial cables under the lead clamp.。
MAIN
RX-1-UNIT
Ｊ01
marking：red
Ｊ09
marking：
black
Ｊ10
Marking : red
Ｊ12
marking：
green
Ｊ04
Ｊ11
marking：
none
Ｊ02
marking：
none
Ｊ03
Marking :
Green
Ｊ05
SUB
RX-2-UNIT
When installing the filters (XF-129CN/ XF-129SN) on the MAIN
side（RX-2-UNIT)
2.Remove the RX-2-UNIT cable.
Coaxial ：4 cables(w/o VCT-101), 6 cables (w/VCT-101)
FFC cable：1 cables (w/o VCT-101), 2 cables (w/VCT-101)
MAIN
RX-1-UNIT
SUB
RX-2-UNIT
Ｊ01
marking：blue
Ｊ09
marking：
black
Ｊ10
marking：red
Ｊ12
marking：
none
Ｊ04
Ｊ02(MP)
marking：
none
Ｊ03(MP)
marking：
green
Ｊ05 (w/VCT-
101)
Note: If you find it difficult to remove the coaxial cable, we may
provide you with a special jig. Please contact our Technical
Support desk.
SUB
RX-2-UNIT
SUB
RX-2-UNIT
MAIN
RX-1-UNIT
When installing the filters (XF-129CN/ XF-129SN) on the MAIN
side（RX-2-UNIT)
3. Remove 6 Screws and remove the RX-2-UNIT from the chassis.
SUB
RX-2-UNIT
XF05
XF-129CN(SUB) XF06
XF-129SN(SUB) XF06
XF05
IN
IN
When installing the filters (XF-129CN/ XF-129SN) on the MAIN side（RX-2-UNIT)
4. Insert the filter in the specified positions and solder it.
※Cut the lead of filters to 2.0 mm or less, after the installation.
Please install the filters in correct
direction.
If installed in reverse, the performance
quality cannot be guaranteed.
When installing the filters (XF-129CN/ XF-129SN) on the MAIN
side（RX-2-UNIT)
5.Attach the RX-2-UNIT to the chassis.
Fix and tighten the screws in order 1 → 2 → 3 → 4. For the rest of
screws, there is no specific order.
SUB
RX-2-UNIT
5.0kgf・cm {0.49Ｎ・m}
Put in the holes in the chassis
①
②
③
④
Autres manuels pour FTDX101D
3
Autres manuels Yaesu Émetteur-récepteur
Yaesu
Yaesu FTM-6000R Manuel utilisateur
Yaesu
Yaesu FT-450 Manuel utilisateur
Yaesu
Yaesu FT-1500M Manuel utilisateur
Yaesu
Yaesu FT-101ZD Manuel utilisateur
Yaesu
Yaesu FT DX 9000 CONTEST - 2 Manuel utilisateur
Yaesu
Yaesu FTM-100DR Manuel utilisateur
Yaesu
Yaesu FT-65R Manuel utilisateur
Yaesu
Yaesu FT-2900R Manuel
Yaesu
Yaesu FT-2400H-3 - SERVICE Manuel utilisateur
Yaesu
Yaesu FT-847 Manuel
Yaesu
Yaesu FT-767GX Manuel utilisateur
Yaesu
Yaesu FT2DR Manuel utilisateur
Yaesu
Yaesu FT-207R Manuel utilisateur
Yaesu
Yaesu FT-8100R Manuel
Yaesu
Yaesu FT2DR Manuel
Yaesu
Yaesu FT-DX100 Manuel utilisateur
Yaesu
Yaesu FT-227R Memorizer Manuel utilisateur
Yaesu
Yaesu FTM-10R Manuel utilisateur
Yaesu
Yaesu FT-690RII Manuel utilisateur
Yaesu
Yaesu FT-902DM Manuel utilisateur
