Xvive Audio U2 Manuel utilisateur
GUITAR
WIRELESS SYSTEM
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT REMOVE SCREWS. NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THE APPLIANCE TO RAIN OR
MOISTURE.
Radio Approvals: FCC Part 15.249, FCC Part 15 B, RSS-210
(Canada), EN 300 440 (Europe), EN 301.489 (Europe), Japan
Radio 2.4GHz Band (Japan), MIC ARIB STD-T66 (Japan)
The CE Declaration of Conformity & California 65 Test
Report can be obtained at
http://www.xviveaudio.com/productInfo.asp?id=354
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
01
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSEUNDESIRED OPERATION.
Warning: Changes or modifcations not expressly approved
in writing by Xvive may void the users authority to operate
this equipment.
RF Exposure Statement: This transmitter must not be
co-located or operated in conjunction with any other
antenna or transmitter.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
CERTIFICATION
in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
This Class B digital apparatus complies with Canadian
ICES-003.
02
1. Observe all instructions carefully in the U2 manual.
2. Do not to perform service operations beyond those
described in the U2 Manual. Services required when the
apparatus has been damaged in any way, such as:
t-JRVJEIBTCFFOTQJMMFEPSPCKFDUTIBWFGBMMFOJOUPUIF
apparatus
t5IFVOJUIBTCFFOFYQPTFEUPSBJOPSNPJTUVSF
t5IFVOJUEPFTOPUPQFSBUFOPSNBMMZPSDIBOHFTJO
performance in a significant way
t5IFVOJUJTESPQQFEPSUIFFODMPTVSFJTEBNBHFE
IMPORTANT SAFETY INSTRUCTIONS
PLEASE THESE INSTRUCTIONS
IN A SAFE PLACE
WARNING: BEFORE USING YOUR XVIVE U2 DIGITAL WIRELESS SYSTEM,
CAREFULLY READ THE OPERATING INSTRUCTIONS.
3. Do not place near heat sources, such as radiators, heat
registers, or appliances which produce heat.
4. Guard against objects or liquids entering the device.
Do not use or place unit near water.
5. Clean only with a damp cloth.
6. Only use attachments/accessories specified by the
manufacturer.
7. Prolonged listening at high volume levels may cause
irreparable hearing loss and/or damage. Always be sure
to practice “safe listening.”
03
Xvive U2 guitar system features digital wireless technolo-
gy that delivers incredible audio quality, simple setup, and
is extremely reliable for any gigging musicians. It delivers a
full 20 Hz - 20K Hz frequency response, so you’ll hear your
guitar tone in great detail with only 6ms of latency. This
wireless system operates at 2.4G Hz ism band for crystal
clear broadcasting ensuring the integrity of your signal on
stage and covers 70 feet of range without any signal
dropout. The li-ion batteries help makes the U2 wireless
system environmentally friendly that can last up to 5 hours
per charge. The chassis is made out of a durable abs plastic
that can withstand the rigors of touring and the harshest
of climates. This wireless is a perfect fit for any pedal board
thanks to its simplistic, and compact design. So, go
wireless with the xvive U2 system. It’ll declutter the stage
and offers freedom in motion
U2 Guitar Transmitter 1PCS
U2 Guitar Receiver 1PCS
USB cable 1PCS
Manual 1PCS
PRODUCT INTRODUCTION PACKAGE DETAILS
04
or
or
QUICK START
05
1. Transmitter plugs into the Guitar (you instruments), the
receiver plugs into the effects pedal, AMP, Audio, etc.
2. Turn on the Transmitter and the receiver and check the
LED blue lights flashing times and make sure the blue
led lights have same flashing times which means
transmitter and receiver are in both same channels.
channels 1 flash once
channels 2 flash twice
channels 3 flash three times
channels 4 flash four times
QUICK START DIAGRAM
06
3. After connecting successfully, LED lights on receiver will
keep light on.
4. Now, let’s rock together.
Hello!
1. Power – Slide Switch to turn on/off
ÓTRANSMETER/RECEIVER
2. Power LED and Battery LED
ÓSolid Red LED indicates the power on,
ÓThe flashing red LED indicates the battery is low charge, it needs
to be recharged .
ÓIn the progress of charging, the light will stop flashing and will
turn off when it is fully charge.
3. Channel Select - Align TRANSMITTER and RECEIVER channels.
ÓDouble click the switch to activate
the channel select function.
ÓFollow the diagram below to set up
the channel , meanwhile the audio
signal indicator LED will flash to
indicate the channel.
BASIC OPERATION
07
FOR THE FLASHING CHANNEL
INDICATION, PLEASE REFER
TO CHART 1
4. Transmitter Audio signal indicator LED
ÓWhen Power is on, the Blue LED will flash to indicate the
pre-set channel.
ÓAfter activating the channel selection function, click the
button to set up the channel , the blue LED will flash to
indicate the channel
* For the flicking channel indication, please refer to chart 1*
Receiver Audio Signal indicator LED
ÓWhen the power is on, the blue LED will flash to indicate
the pre-set channel .
ÓAfter activating the channel selection function, click the
channel button, the blue LED will flash to indicate the
channel
ÓThe Receiver audio signal indicator LED will become
solid blue when the Transmitter and Receiver are in
alignment.
Channel 1 The Audio signal LED will flash once
Channel 2 The Audio signal LED will flash twice
Channel 3 The Audio signal LED will flash three times
Channel 4 The Audio signal LED will flash four times
ÓWhen the signal is good, The receiver audio Signal
indicator LED will become solid blue, it will start to flash
if the signal is not good .
*For the flashing channel indication, please refer to chart 1*
5. USB Port – Battery recharger port.
BASIC OPERATION
08
* Chart 1, Flashing channel indication
Note:
In an emergency, power can be supplied via a USB wall
adapter however, the battery life will be reduced.
* Always store U2 at room temperature
* When storing the unit, please check the battery
state regularly and charge if necessary.
0:15 min
0:30 min
1 hour
2 hours
30 min
1 hour
2 hours
5 hours
CHARGING TIMES BATTERY LIFE
Connect to the socketConnect Power
BATTERIES AND CHARGING
09
Table des matières
