Xview XV20DVR Manuel utilisateur
XV20DVR / XV22DVR
USER MANUAL
xviewdrive.com.au
for more information on
the Xview range go to
our website
VIEW
INCLUSIONS:
Dash Cam, GPS power cable, cable, charger, memory card.
(XV22DVR model: rear camera, rear camera cable)
2
Micro USB
Power Socket
Hand Gesture Sensor
Camera
Red: Flashing when recording
Green: Mobile phone connected
Reset
LED Indicators
MIC
Adhesive
Mount
Memory
Card Slot Rear
camera
input
Reset
1. PRODUCT PICTURE AND FUNCTION
Speaker
VIDEO
3
Memory Card Slot
Car camera supports up to
64GB TF card, and
Class 10 TF card is
required.
1. Insert Micro SD card
2. INSTALLING THE DASH CAM
2. Mounting
2.1 Check the orientation of the Dash Cam camera first
before installation. When the Dash Cam lens is facing
outwards, the Hand Gesture Sensor faces down.
2.2 Use an Alcohol wipe to clean the windscreen and
enhance adhesion.
2.3 Fix the Dash Cam on the inside surface of the
windscreen by removing backing off 3M tape and press &
hold firmly to windscreen for 60 seconds. The area near the
rear-view mirror is suggested where the vision is not blocked.
Do not install the device on the vehicles airbag or within its
working range.
2.4 Insert the Micro USB end of the GPS power cable into
the Micro USB Power socket/ charging point of the Dash
Cam. Fix the GPS power cable on the inside surface of the
windscreen by removing backing off 3M tape and press &
hold firmly to windscreen for 60 seconds. For a better GPS
signal, make sure the 3M sticker faces toward the sky and is
not blocked or obstructed. Connect USB charging end of the
GPS power cable into 12/24V power socket of vehicle.
4
2.5 Turn the vehicles ignition on and the Dash Cam will
power ON and start recording automatically, you will hear an
audible tone and voice prompt says ‘recording’.
2.6 When recording the LED light indicator will flash red.
2.7 For the Dash Cam to work it must receive power from the
charging adapter. Once power is removed or turned off the
Dash Cam will save the current file and turn off.
NOTE: The Dash Cam power cable must be used to retain
date and time settings.
2.8 Rotate the camera direction to get the best view.
2.9 Once position of the camera is OK hide the cable like the
positioning diagram below.
Suggested
GPS
5
3.1. Insert the rear camera cable into the video input of the
Dash Cam and test.
3.2. Then run the cable to the rear cameras location.
3.3. Fix the cable along the ceiling or A-pillar where it can be
safely hidden. (Drivers side see picture below)
3.4. Then mount the rear camera to the inside of the vehicles
window, with the cable input facing the drivers side.
3. INSTALLING THE REAR CAMERA (XV22DVR model)
6
4. CONNECTING TO WIFI
Recording video, taking photos, live streaming, GPS data,
download files and changing Dash Cam settings can all be
done via WiFi and downloading the ‘Xview XV20/22’ Dash
Cam APP. For iPhones search the APP Store or for Android
devices via Google Play.
4.1 Power up your Dash Cam
4.2 Make sure that you have your “LOCATION” turned on,
and your “MOBILE DATA” turned off in the settings of your
smartphone.
4.3 To pair the Dash Cam with your smartphone, go into the
settings menu on your smartphone and turn WiFi on to and
display all devices for connection.
4.4 Select your Dash Cam model SSID name eg: XV22DVR.
4.5 Enter the password 12345678.
4.5 Once successfully paired to your DASH CAM the Dash
Cam will say WiFi Connected
4.6 Once connection is successful, the indicator light on the
side of your Dash Cam turns red.
4.7 After your initial pairing of your device to the Dash Cam’s
WiFi network you can turn back on your mobile data. For all
future pairing you do not need to disable your mobile data.
However, if you have an issue that looks as if the phone
cannot get data from the device you may try disabling mobile
data as a possible remedy.
7
Pairing screen
5. USING THE APP
5.1 Launch the ‘Xview XV20 or XV22’ Dash Cam APP to
access functions.
5.2 Select “Connect to DVR” to enter the App.
5.3 App screen should look like image below.
8
5.4 When in portrait mode a live image of the Dash Cam’s
view will be displayed at the top of the phone screen. Use this
image to adjust the angle of the camera so that the lower part
of the cameras view can see the end of the cars bonnet (about
¼ of its length)
5.5 To take a picture, press the white button in the lower
centre of your screen
5.6 To access your Dash Cam videos, press the video camera
icon in the lower centre of your screen
5.7 To access the Dash Cam’s settings, press the settings
gear icon in the lower centre of your screen
5.8 To view your files via the APP, click on the video icon on
the interface screen. Select the recorded video or photo file
you wish to view under the appropriate heading. This will open
up the playback screen and start playing the recorded video or
photo.
5.9 Select the downloading icon and the selected file will
download from the DASH CAM to your Smartphone for
viewing. Use the same procedure for pictures. Alternatively
press the select wording, click on individual files and press the
download arrow icon. You can also remove the SD card from
the Dash Cam and plug the card directly into your computer to
access files.
5.10 To set the time and date, click on the gear icon and scroll
down to where it says "Sync the mobile phone time to
device”. Click on this option and it will then set the Dash Cam
timeto the same time as your mobile phone. A confirmation
message is also given.
9
2. Mounting
2.1 Check the orientation of the Dash Cam camera first
before installation. When the Dash Cam lens is facing
outwards, the Hand Gesture Sensor faces down.
2.2 Use an Alcohol wipe to clean the windscreen and
enhance adhesion.
2.3 Fix the Dash Cam on the inside surface of the
windscreen by removing backing off 3M tape and press &
hold firmly to windscreen for 60 seconds. The area near the
rear-view mirror is suggested where the vision is not blocked.
Do not install the device on the vehicles airbag or within its
working range.
2.4 Insert the Micro USB end of the GPS power cable into
the Micro USB Power socket/ charging point of the Dash
Cam. Fix the GPS power cable on the inside surface of the
windscreen by removing backing off 3M tape and press &
hold firmly to windscreen for 60 seconds. For a better GPS
signal, make sure the 3M sticker faces toward the sky and is
not blocked or obstructed. Connect USB charging end of the
GPS power cable into 12/24V power socket of vehicle.
6. USING GPS FUNCTION
6.1 To use the GPS function, the GPS antenna module must
be plugged into the Dash Cam.
6.2 For GPS data go into the settings menu on your Dash
Cam App and turn GPS on.
6.3 This function is only valid when the external GPS module
is connected. After the external GPS is connected, this
function can be turned on to record, store and output data of
the driving speed, time, mileage and other state information
of the car.
6.4 When activated a GPS symbol will appear on the App
screen and flash, until it receives a signal then it will turn
green
6.5 The GPS data is automatically saved to the video files.
In order to view the GPS data using the mobile phone APP,
you need to download the video file in the Dash Cam to your
mobile phone.
6.6 Then you must disconnect from the Dash Cam.
6.7 Click on the GPS Log icon at the bottom of the App
viewer page.
6.8 You can also download a free GPS player for your
computer to display data on our website.
10
8. G-SENSOR FUNCTION
9. PARK MODE FUNCTION
7. HAND GESTURE PHOTO FUNCTION
Whilst recording you can wave your hand in front of the hand
gesture sensor, the Dash Cam will make a click sound and
automatically takes a photo. It will also capture and save 10
seconds of the current recorded video, 5 seconds before and
5 seconds after hand gesture initiation.
G-sensor Sensitivity: High, Medium, Low Sensitivity or
Shutdown (Turn off) and available. This function activates in
the case of a car accident. When this function activates the
Dash Cam will automatically sync a 10 second video clip and
save it to the Event folder on the SD card. We recommend
Low Sensitivity to avoid false triggers.
Note: With this function turned on it may fill up the SD card
with locked video files. Re-format the SD card to create
space. The device does NOT guarantee video recording of all
accidents as built-in impact sensor may not be activated due
to combination of user settings and the level of impact during
the collision.
After 10 minutes of the vehicle being parked. An audio message
will announce “in park mode”. It will start recording 10 second
video footage when motion triggered. When ignition is turned on
park mode turns off and the Dash Cam will return to continuous
recording. (Requires installation with optional XVIEW Hard Wire
Kit (XVHWC).
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Xview Caméra embarquée
