Xerox WorkCentre M118 Instructions d'installation et d'entretien
XEROX®WORKCENTRE M118 • 128
DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
XEROX®WORKCENTRE M118 DRUM CARTRIDGE
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
1. Remove the two screws located on the handle side end cap. Remove the end cap.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
REMANUFACTURING THE XEROX WORKCENTRE
M118/128 DRUM CARTRIDGE
By the Technical Staff at UniNet
SUPPLIES REQUIRED
1. Xerox WorkCentre M 118/128 developer (used in OPC cartridge)
2. Xerox WorkCentre M 118/128 drum cartridge replacement chip
3. Xerox WorkCentre M 118/128 OPC drum
4. Xerox WorkCentre M 118/128 wiper blade
5. Conductive Grease
TOOLS REQUIRED
1. Phillips head screwdriver
2. Small common screwdriver
3. Vacuum approved for toner
2. Remove the four screws from the inner end cap. Remove the end cap.
3. Follow the wires from the inner end cap to the sensor.
Pry up on the two locking tabs and remove the sensor.
Place a small piece of tape over the sensor hole.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
4. On the non gear side, remove the four screws from the end cap.
Remove the end cap.
5. On the large gear side, remove the metal plate and the drum bushing.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
6. On the opposite side (non gear side) pry off the white gear and the drum bushing.
7. Carefully separate the two halves. 8. Remove the drum and place aside.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
9. Remove the PCR. 10. Remove the two screws from the wiper blade.
Remove the blade.
11. Clean out any toner from the hopper.
Make sure you also clean out the auger post.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
12. Install the new wiper blade and two screws. 13. Clean the PCR with your normal cleaner. Wipe off the old
conductive grease from the shaft and replace. Re-install the
PCR in the assembly grease side to the black PCR holder.
14. Place the drum in the hopper and carefully place aside. 15. On the developer roller side, remove the two springs from
the metal slide cover.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
16. Remove the plastic spring arm, and the two screws.
17. Remove the screw from the contact plate on the opposite
side of the hopper.
18. Carefully pry up the three plastic tabs on the back edge of
the cartridge.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
19. Lift off the cover and locate the chip. 20. From the inside of the cover remove and replace the chip.
21. Remove all the old developer from the hopper. 22. Pour in the new developer.
Make sure you cover both augers.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
23. Snap the cover back in place.
Make sure all three tabs lock!
24. Install the back screw in front of the metal cover.
25. Install the plastic spring arm and the screw to hold it in
place (sliding the cover over allows the spring arm to fit
correctly).
26. On the opposite side, install the screw into the metal
contact.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
Autres manuels pour WorkCentre M118
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Xerox Imprimante
Xerox
Xerox Phaser 6110 Manuel utilisateur
Xerox
Xerox DocuPrint P1210 Manuel utilisateur
Xerox
Xerox 4050 Manuel utilisateur
Xerox
Xerox DocuPrint N4525 Manuel utilisateur
Xerox
Xerox VersaLink C9000 Manuel utilisateur
Xerox
Xerox Docuprint 75 Manuel technique
Xerox
Xerox Phaser 3020 Manuel d'utilisation
Xerox
Xerox 4050 Guide de référence
Xerox
Xerox Nuvera 100 Manuel utilisateur
Xerox
Xerox Synergix 8850 Manuel utilisateur
Xerox
Xerox Phaser 4510 Manuel utilisateur
Xerox
Xerox 8550YDP - Phaser Color Solid Ink Printer Manuel utilisateur
Xerox
Xerox Synergix 8830 Manuel utilisateur
Xerox
Xerox WorkCentre 5638 Manuel d'utilisation
Xerox
Xerox DocuPrint 377CF Mode d’emploi
Xerox
Xerox 7700 Manuel utilisateur
Xerox
Xerox C310 Manuel utilisateur
Xerox
Xerox C11 - DocuPrint Color Inkjet Printer Manuel utilisateur
Xerox
Xerox 3250D - Phaser B/W Laser Printer Manuel utilisateur
Xerox
Xerox 8860MFPD - Multifunction Inkjet Printer Manuel utilisateur
