Xerall X-TANKCOPTER Manuel utilisateur
Instruction Manual
Ages 14 +
X-TANKCOPTER
www.xerall.com
www.xerall.com
2
Catalogue
Overview of drone and transmitter 3
Part loading and unloading 7
Precautions before flying 10
Flying procedures 11
Function introductions 16
Know your App 18
Precautions before taking photos 19
Assembly parts list 20
Troubleshooting 22
www.xerall.com
www.xerall.com
3
Overview of drone and transmitter
Drone
Propeller A
Left Right
Front LED
Back LED
Belt
Propeller B
Propeller B
Propeller A
HD Camera
Battery Cover
Tank Drone
Cover
Tank Drone
Bottom
Main parameter
Drone Size
Drone Weight
Propeller Diameter
252x203x55.2mm
123g
92.6mm
Flying Time About 6~7 mins
About 50m
About 90~120 mins
3.7V 900mAh
About 25m
Running Time About 20~30 mins
Drone Battery
Charging Time for
Drone Battery
Flying distance/radius
Driving distance/radius
1280x720PCamera pixels
www.xerall.com
www.xerall.com
4
Exploded View
16 Front Right Motor Cover
15
No. Name No.Name
1Belt
17 Front Left Motor Cover
2Propeller A
18 Reverse Motor (White Plug)
3Propeller B
19 Forward Motor( Red Plug)
4Tank Drone Cover
20 Battery Cover
5Dash Receiver
21 Rear Left Motor Cover
6Camera Press
22 Rear Right Motor Cover
7Iron Shaft Sleeve
23 Belt Rotated Gear Shaft
8Camera Plate
24 Rotary Tooth Of Model T
9Bearing
25 Rear Bracket
10 Tank Drone Bottom
Chief Axis
26 Rear Belt Rotating Wheel
11
Gear Wheel
27 Belt Motor
28 Belt Motor Cover
12
Front Bracket
13
Front Belt Rotary Wheel
14
Belt big Wheel
15
15
12
26
23
22
21
20
18
17
16
15
14
14
13
13 12
11
11 09
09
07
09
07
06
05
03
01
28 27
03
04
02
04
10
09
08
18 17
23
24
25
27
28
24
25
26
12
11
09
09
07
12
11
09
19
15
01
www.xerall.com
www.xerall.com
5
Controller Button Functions
Left Stick:
Right Stick:
Power Switch:
To control the drone taking off /landing/ left side flying/ right side flying; To control its right
turning while flying.
To control the drone forward/backward/left side flying/right side flying; To control its left
turning while flying.
Press the key to the headless mode, press it again to exist the function.
Press it for taking a picture, and press it for two seconds, it starts to make videos.
Click on this button to start the function of high/low speed mode switching.
Press the key before taking off, the drone will make
Press the key down, pull the right control rod to the direction you wanted,
then it can go under your control, release to exist.
When pressing down the key, it’s changed to the flying mode, press it
again to come to the ground mode.
automatic flying; Press the key while flying, the drone will land automatically or press the key for a while,
the drone will land on the ground directly.
Press down the power switch to turn on the remote controller, press it down again to
turn off the remote controller.
Photo / Video:
Flight / Ground Switching:
Trimmer Mode Button:
High / low speed:
Heading Hodl Mode:
Take Off / Landing / Emergency Stop Button:
Transmitter
Power
Indicator
Heading Hold
Mode
Photo / Video
Phone Holder Slot
Left Stick Right Stick
High/Low Speed
One Button Take
Off / Landing/
Emergency
Stop Button
Power Switch
Flight / Ground
Switching
(Press Down)
Trimmer Mode Button
(Press Down)
Notice: Taking photo and recording video are available after connecting with
smart phone.
www.xerall.comwww.xerall.com
www.xerall.com
6
Battery Installation
Open the battery cover on the back side of the transmitter, insert 4 AA batteries
following the polarity indicators. (Picture 1/2, battery is not included.)
Alkaline Battery
Picture 1 Picture 2
Battery Cover
Phone Installation Instruction
Notice：Make sure that the button on the phone is not clamped.
Picture 3 Picture 4 Picture 5 Picture 6
1. Take out the phone holder and insert into the controller(Picture 3).
3. When taking out the phone clip, you need to press the clip buckle behind the phone
clip at the same time, so that the buckle can be closed and removed easily.
2. Pull out upper clamp of the holder ( Picture 4/5), put the phone into the holder,
then release the clamp, and the phone will be fixed on the holder( Picture 6).
1.Make sure the electrodes are correct.
2.Do not mix new with old batteries.
3.Do not mix different kinds of batteries.
4.Do not charge the non rechargeable battery.
Notice:
www.xerall.com
www.xerall.com
7
Propeller Installation Diagram
Note: When installing, please make sure
to have the right installation for
propeller, otherwise the drone can’t
be operated normally.
Picture 7
When removing the propeller, firstly using the screwdriver for distribution to
loosen the screw on the top of the propeller, then you can take out the broken
propeller. (Picture 7).
When loading the propeller, firstly please insert the new propeller to the iron
sleeve, then twist the screw in the right place, it’s ready for operation now.
Installing & Removing Component
Drone Battery
Li-Po Battery Disposal & Recycling
Wasted Lithium-Polymer batteries must not be placed with household
trash. Please contact local environmental or waste agency or the
supplier of your model or your nearest Li-Po battery recycling center.
Charging Instruction for Drone Battery
* For faster charging, it is recommended to use an adapter with 5V 2A output current
(not included) to charge the battery
Power BankPhone Charger
Car ChargerComputer Charging
1. Connect the drone battery with USB cable first and then choose one of the
method as the picture below shows to connect with USB plug.
2. The red USB indicator light keeps bright when charging and the light turns
green when fully charged.
www.xerall.com
www.xerall.com
8
Picture 8
Picture 9
Picture 10
Diagram of belt loading and unloading
Picture 11
Motors Replacement
WARNING: The motor’s rotating direction should be the same, or it will not work.
Note: The motor is consumable. If it is damaged, visit the local seller to buy the
new motor for replacement.
When installing the belt, please belt up the front/rear rotating wheel and belt wheel.
When disassembling the belt, you can pull out the belt out from the front/ rear
belt rotating wheel and the belt wheel.
1. Twist out the the four screws of the motor cover anticlockwise with the
screwdriver for distribution (Picture 8).
2. Twist out the screws of the scaffold, then open the motor cover (Picture 9).
3. Please firstly take out the broken motor, connect the plug in the relative color
to the plug motor, then install the motor to the battery jar, close the motor
cover, lock the screws, it’s finished now(Picture 10).
www.xerall.com
www.xerall.com
9
Diagram of scaffold loading and unloading
Picture 12 Picture 13
Rear BracketFront Bracket
1. Please twist out the screws of the front support bracket anticlockwise with the
screwdriver for distribution (Picture 12), take out the broken bracket,then
replace a new one.
2. Please twist out the screws of the rear bracket anticlockwise with the
screwdriver for distribution, pull out the plug to take out the broken bracket,
then replace a new one ( Picture 13).
Picture 14
Picture 15
Diagram of battery installation
1. Press the battery cover to the right position as the direction the arrow shows
( Picture 14).
2. Open the battery cover upward ( Picture 15）, then insert the lithium battery to
the battery box, insert battery plug and tank drone socket, lock the battery
cover. It’s ready now.
www.xerall.com
www.xerall.com
10
Precautions before flying
1. Please make sure that the battery power of the drones and the transmitter are
in a state of saturation.
2. Before turning on the transmitter, please make sure that the left stick is in the
middle position.
3. You must obey the right order of turning ON the power. Firstly, you
should turn on the transmitter, next to make the connection for the power
supply of the drone; While before turning off the power, you must disconnect
the drone first, then to turn off the transmitter. For improper order may cause
the drone out of control, thus may do damage to the safety of yourself and
others. So please cultivate a good habit of connecting and disconnecting the
power supply.
4. Please confirm that the connection between lithium batteries and motors and
other components is reliable. If there’s continuous vibration while flying, thus
may cause the loosen of the attaching plug. Finally, the drone will be out of
control.
5. Please confirm the directions of propeller rotation. Propeller A of the front and
rear propellers runs clockwise rotation. And propeller B of the right front and
left rear runs counterclockwise rotation.
6. Improper operation may cause air crash, and it may make the motor or
propellers work badly or make noise. Thus situations all lead to the flying state
or it can’t fly. If so, we suggest you to purchase new components from the
local seller to replace it in time. And thus the drone can return to the best state.
7. Please check to see whether the plug line connection is firm, be sure that the
gear can not be wound to sundries, and to ensure smooth skating, or it may
do damage to the driving motor.
8. If there’s loosening of a belt, running on the ground is one side or no driving;
And while flying, it make addle the propeller of a belt and cause a runaway
crash.
www.xerall.com
Table des matières
