XENO XLCD17-LED Manuel utilisateur
USER MANUAL
For
XLCD17-LED
XLCD19-LED
2
3
TABLE OF CONTENTS
CE information ------------------------------------------------------------------------ 4
Safety Precautions ------------------------------------------------------------------- 4
1. Scope -------------------------------------------------------------------------------------- 6
2. Functional specification ------------------------------------------------------------- 6
3. Controls and indicators -------------------------------------------------------------- 8
4. OSD Menu -------------------------------------------------------------------------------- 9
5. Regulatory Agency ----------------------------------------------------------------- 20
6. Reliability ----------------------------------------------------------------------------- 20
7. Mechanical ------------------------------------------------------------------------------ 21
4
CE INFORMATION
The product must be installed according to the currently valid installation regulations for
EMC to guarantee the designed use and to prevent EMC problems.
The device supplied with this manual is according to the EC, EMC Directive,
2004/108/EC, LVD 2006/95/EC and RoHS 2011/65/EU
SAFETY PRECAUTIONS
1. Do not modify the three-prong grounding type monitor power plug in any way.
2. Operate this unit only from the type of power source indicated on the label.
3. Do not block or cover ventilation openings on the back or bottom of the monitor cabinet.
4. Do not place this monitor near a radiator or heating vent.
5. Do not push objects of any kind through cabinet openings. This may result in fire or
electrical shock.
6. Before adding attachments always ask a service technician to perform routine safety
tests to determine that equipment is in safe operating condition. Ground potential tests
should be part of the routine safety check made by the service technician.
7. Do not place monitor on an unstable cart, stand, or shelf where it may fall and injure
personnel or damage equipment.
8. Route power cords so that they cannot be walked upon or tripped over. Do not allow
anything to rest on the power cord.
9. Do not install monitor in wet areas, or where it may be exposed to rain or water. Do not
spill liquid of any kind on the unit.
10.Unplug the power cord from the unit before cleaning the display. Use only a damp cloth.
Do not use alcohol, spirits, or ammonia to clean the display. DO NOT ATTEMPT TO
CLEAN THE INTERIOR OF THIS UNIT- THIS ACTION MUST BE PERFORMED BY
THE SERVICE TECHNICIAN AS REQUIRED DURING NORMAL MAINTENANCE.
11.Refer all servicing to qualified service personnel. REMOVAL OF BACK COVER BY
UNAUTHORIZED PERSONNEL MAY EXPOSE THE USER TO DANGEROUS
VOLTAGES OR OTHER HAZARDS.
12.Unplug the unit immediately and notify the service technician.
A. If liquid has been spilled into the display or the display has been exposed to rain or
water.
B. If the unit has been dropped or the cabinet damaged.
C. If fuses continue to blow.
D. If the power cord is damaged or frayed.
E. If a distinct change from normal operation is apparent.
5
When replacement parts are required, be sure that the service technician uses components
specified by the manufacturer which have the same characteristics as the original parts.
UNAUTHORIZED SUBSTITUTIONS MAY RESULT IN FIRE, ELECTRICAL SHOCK OR
OTHER HAZARDS.
Upon completion of any service or repairs, ask the technician to perform safety checks to
determine that the equipment is in safe operating condition.
WARNING:
SERIOUS SHOCK HAZARDS EXIST WITHIN THE COVERS OF THIS MONITOR. DO
NOT OPEN THE COVERS UNDER ANY CIRCUMSTANCES,
THERE ARE NO USER SERVICEABLE COMPONENTS INSIDE
CAUTION - USE RECOMMENDED MOUNTING APPARATUS TO AVOID RISK OF
INJURY
6
1. Scope
This specification is used to define the performance of XLCD series color TFT LCD
(LED Backlit) monitor. This system also supports both video input and PC input. In video
input mode, the system can automatically detect the NTSC signal and PAL signal. In PC
mode, this system can support up to 1920 x 1080 VESA standard.
The user friendly OSD menu makes this monitor easy to operate.
2 Functional Specifications
2.1 Power Supply
The power supply spec is listed below,
AC INPUT
* AC power input range: 100 –240 V, 50-60Hz, 1.8Amps max.
* Power efficiency: ≥80%
DC INPUT
* DC JACK power input: 12V +/-10% 2.3A max.
2.2 Video Characteristics
Composite Video (CVBS): 1.0 Vp-p (0.5 –1.5Vpp), Automatic switching from 75
unbalanced termination to Hi-Z with loop-through operation.
Y/C (S-video): 1.0 Vp-p (0.5 –1.5Vpp), Automatic switching from 75 unbalanced
termination to Hi-Z with loop-through operation.
2.3 PC Input
VGA Input
Analog RGB: 0.707 Vrms.
Support VESA Standard Timing
DVI Input
DVI 1.0 Compatible Interface
Support VESA Standard Timing
2.4 Audio Input
Signal Level: 1.0 Vrms
7
2.5 Environmental
Temperature
Operating: 00C to +400C
Storage: -200C to +600C
Humidity
Operating: 10% to 85% (non-condensing)
Storage: 10% to 95% (non-condensing)
2.6 EDID
This series of displays support EDID, but does not support DDC2B function.
2.7 Connectors
H G F E D C B A
A. DC 12V INPUT: DC JACK, 5.5Ø / 2.5Ø
B. DVI INPUT: 24 pins DVI-D Connector
C. VGAINPUT: D-SUB 15 pins Connector
D. S-VIDEO (Y/C) INPUT: Mini-DIN 4 pins Connector
E. CVBS INPUT: BNC Connector
F. CVBS OUTPUT: BNC Connector
G. AUDIO INPUT: Phone Jack, Stereo
H. AUDIO OUTPUT: Phone Jack, Stereo
Set up sequence
1. Make sure the power of PC and/or Video source is turned off.
2. Connect the monitor to the video source or PC and plug in the power
supply.
3. Turn on the PC and/or Video source power.
4. Turn on the monitor power supply.
(Use reverse sequence to teardown the monitor)
8
3. Controls and indicators
A. “i” Channel button
Press the button to select input signal.
B. “-“ / “+” buttons
Press the buttons to scroll the cursor to desired function.
Press the buttons to adjust the value of selected function in sub OSD menu.
C. “M” Menu button
Press the button to show the OSD main menu.
As a confirmation key during the OSD operation.
D. POWER LED Indication
Green - Power on
Orange - Power off (Stand by)
Flashing Orange - Sleep mode (PC mode only)
Flashing Green - Freeze
E. POWER button
Press the button to turn ON or turn OFF the monitor.
9
4. OSD Menu
OSD Menu structure
Use the CHANNEL button to select VGA, DVI, S-VIDEO, or AV CVBS , the menu
structure within each varies, refer to sections below on how to set-up each option.
PC mode: VGA and DVI
Press the Menu button to bring up the MAIN MENU Page. The following page will appear
Press -/+ buttons to select an icon, then Press MENU button to change the values in the
sub menu.
10
COLOR ADJUST
1. Press - / + buttons to select an icon
2. Press MENU button to select item,
3. Press - / + buttons to adjust the value
4. Press MENU button to return
5. Press Input button (i) to return the MAIN MENU Page.
AUTO COLOR Press MENU buttons to auto adjust the color
CONTRAST Adjust the contrast value
BRIGHTNESS Adjust the brightness value
COLOR TEMP Press MENU button to select the sub-menu
Set the color temperature of the LCD monitor for the CIE coordinate Cool MODE or
Warm MODE or Normal MODE or Personal MODE
Ce manuel convient aux modèles suivants
1
Table des matières
