X10 TM751 Manuel utilisateur
X10WirelessTechnology,Inc.LIMITED1-YEARWARRANTY
X10.com, a division of X10 Wireless Technology, Inc. (X10) warrants X10 products to be
free from defective material and workmanship for a period of one (1) year from the original
date of purchase at retail. X10 agrees to repair or replace, at it’s sole discretion, a defective
X10 product if returned to X10 within the warranty period and with proof of purchase.
If service is required under this warranty:
Return Merchandise Authorization (RMA) number.
2. Return the defective unit postage prepaid to X10 (see address on back).
3. Enclose a check for $4.00 to cover postage and handling.
4. Enclose a dated proof of purchase.
5. X10 is not responsible for shipping damage. Units to be returned should be packed
carefully.
Please visit www.x10.com/warranty
to complete your on-line warranty registration. Thank you.
Transceiver Module TM751
INSTALLATION AND OPERATING INSTRUCTIONS
The TM751 Transceiver receives commands from X10 Remote controls and
turns on a light or appliance connected to its outlet. The Transceiver also
passes the signals onto your house wiring to control lights, appliances, or
Wireless Cameras around your home. You plug lights and appliances into
X10Modules(soldseparately).YouplugWirelessCamerasintoAddressable
Power Supplies (sold separately).
1. Plug the TM751 Transceiver into any 120V AC outlet. Fully extend its
antenna.
2. Use a dime to set the Housecode dial on the TM751 to match the X10
modules, cameras, and remote controls you will be using it with.
3. PlugalamporapplianceintotheoutletontheTM751(observetheratings
on the back of the TM751).
4. Press the small button on the TM751 to test that the lamp/appliance goes
on and off.
5. Install4AAAalkalinebatteriesinanHR12APalmPadremotecontrol,or
CR12A ScanCam remote control (each sold separately).
6. Press 1 ON and OFF on the remote control to control the light/appliance
connectedtotheTM751.
7. Press the corresponding ON or OFF button on the remote control to turn
other X10 Modules or cameras on/off.
Also see instructions included with X10 remote controls and cameras.
For help or more information on setup, please visit
www.x10.com/support TM751-7/03
FCC CAUTION: THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
This equipment generates and uses radio frequency energy, and if not installed and used properly, that
is, in strict accordance with the manufacturers instructions, it may cause interference to radio and
television reception. It has been type tested and found to comply with the limits for remote control
devices in accordance with the specifications in Sub-Parts B and C of Part 15 of FCC Rules, which are
designed to provide reasonable protection against such interference in a residential installation. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause interference to radio or television reception, which can be determined by unplugging the equip-
ment, try to correct the interference by one or more of the following measures.
• Reorient the antenna of the radio/TV experiencing the interference.
• Relocate the product with respect to the radio/TV.
• Move the product away from the radio/TV.
• Plug product into an outlet on a different circuit from the radio/TV experiencing the interference.
• If necessary, consult your local Dealer for additional suggestions.
NOTE: Modifications to any of the components in this kit will void the user’s authority to operate this
equipment.
Autres manuels X10 Émetteur-récepteur
