WNC DNXA-H1 Manuel utilisateur

PCIe 802.11n WiFi Module

WNC

User Manual

(DNXA-H1)

Version: 1.0

Nov. 2010

No part of this publication may be reproduced, stored in a retrieval system, or

transmitted in any form or by any means, whether electronic, mechanical,

photocopying, recording or otherwise without the prior writing of the publisher.

Windows

™

98SE/2000/ME/XP are trademarks of Microsoft

Corp.

Pentium is trademark of Intel.

All copyright reserved.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate this

equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated

with minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any

other antenna or transmitter.

Operations in the 5.15-5.25GHz band are restricted to indoor usage only.

This device is intended only for OEM integrators under the following

conditions:

1) The antenna must be installed such that 20 cm is maintained between the

antenna and users, and

2) The transmitter module may not be co-located with any other transmitter or

antenna,

3) For all products market in US, OEM has to limit the operation channels in

CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM

shall not supply any tool or info to the end-user regarding to Regulatory

Domain change.

As long as 3 conditions above are met, further transmitter test will not be

required. However, the OEM integrator is still responsible for testing their

end-product for any additional compliance requirements required with this

module installed.

IMPORTANT NOTE: In the event that these conditions can not be met (for

example certain laptop configurations or co-location with another transmitter),

then the FCC authorization is no longer considered valid and the FCC ID can

not be used on the final product. In these circumstances, the OEM integrator

will be responsible for re-evaluating the end product (including the transmitter)

and obtaining a separate FCC authorization.

End Product Labeling

This transmitter module is authorized only for use in device where the antenna

may be installed such that 20 cm may be maintained between the antenna and

users. The final end product must be labeled in a visible area with the following:

“Contains FCC ID: NKR- DNXAH1”.

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user

regarding how to install or remove this RF module in the user’s manual of the

end product which integrates this module.

The end user manual shall include all required regulatory information/warning

as show in this manual.

Table of Contents

1. INTRODUCTION 5

1.1

YSTEM

EQUIREMENTS

.........................................................................................5

1.2

EATURES

.................................................................................................................5

2. DRIVER/UTILITY INSTALLATION / UNINSTALLATION 6

2.1

NSTALLATION

..........................................................................................................6

2.2

DDITIONAL

ETUP

ROCESSES

..............................................................................9

2.3

NINSTALLATION

...................................................................................................10

3. CONNECTING TO AN EXISTING NETWORK 11

4. CREATINGAN AD HOC NEW NETWORK 16

5. MODIFYINGAWIRELESS NETWORK 19

5.1

NFRASTRUCTURE

ODE AND

ODE

.....................................................19

5.2

ODIFYINGA

IRELESS

ETWORK

.....................................................................20

5.3

EFAULT

ETTINGS

INDOWS

ERO

-C

ONFIGURATION

................................27

5.4

UPER

A/G

ETTING

..............................................................................................27

APPENDIX A: FAQ ABOUT WLAN 28

1. Introduction

Thank you for purchasing the PCIe 802.11n WiFi Module that provides the easiest

way to wireless networking. This User Manual contains detailed instructions in the

operation of this product. Please keep this manual for future reference.

1.1 System Requirements

A laptop PC contains:

-32 MB memory or greater

-300 MHz processor or higher

Microsoft

Win

™

2000/ME/98 Second Edition/XP

1.2 Features

Mini-PCI adapter, half size design

IEEE 802.11a/b/g/n compatible: allowing inter-operation among multiple

vendors

Support Atheros Super A/G

Mode

Provide seamless roaming within the IEEE 802.11 a/b/g/n WLAN

infrastructure

Site survey function

2. Driver/Utility Installation / Uninstallation

2.1 Installation

Note! The Installation Section in this User Manual describes the first-time installation

for Windows. To re-install the driver, please first uninstall the previously

installed driver. See Chapter 2.3 “Uninstallation” in this User Manual.

Follow the steps below to complete the driver/utility installation:

1. Insert the Installation Software CD into the CD-Rom Drive.

2. Click “Next”.

3. Read the License Agreement and click “Yes”.

4. Click “Next” to continue or click “Browse” to choose a destination folder.

5. Click “Next”.

6. Click “Yes” to create a shortcut icon on your desktop.

7. Click “Finish”.

8. You should now see a shortcut icon on your desktop.

2.2 Additional Setup Processes

During software installation procedure, each operating system may prompt different

specific options:

1. Windows 98SE: The system will request the original Windows CD during the

installation process. When the installation is finished, you’ll have to restart your

computer.

2. Windows Me: Please restart your computer when the installation is finished.

3. Windows 2000/XP: Select “Install the software automatically” when the window

with this option appears, and then click “Next” to continue installation.

Table des matières

Autres manuels WNC Module sans fil

WNC

WNC DHUR-AZ53 Manuel utilisateur

Manuels Module sans fil populaires d'autres marques

Laird

Laird RM024 Manuel utilisateur

Laird

Laird BT830-SA Guide de configuration rapide

Ebyte

Ebyte E49-400T20S Manuel utilisateur

Fibocom

Fibocom FM101-NA-20 Instructions d'installation

Waldmann

Waldmann EnOcean TALK MODUL G2 Manuel utilisateur

Smartech

Smartech LBT-1.DO4 Manuel utilisateur

Cooper Wiring Devices

Cooper Wiring Devices ESPIRE RF RFAPM Manuel utilisateur

Yuga

Yuga CLM920 Manuel utilisateur

Waldmann

Waldmann TALK Bluetooth Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions UC864-G Manuel d'installation

Ebyte

Ebyte E07-900M10S Manuel utilisateur

Quectel

Quectel SC690A Series Supplément

Panasonic

Panasonic INDUSTRY PAN9028 Guide de configuration rapide

Ebyte

Ebyte E70-433NW30S Manuel utilisateur

LongSung Technology

LongSung Technology U9507E Manuel utilisateur

Wistron NeWeb

Wistron NeWeb DNUR-S2 Manuel utilisateur

Ebyte

Ebyte E49-400M20S4 Manuel utilisateur

RF-Star

RF-Star SimpleLink RF-BM-2652P1 CC2652P Manuel utilisateur