WMH Tool Group JET JDP-15M Manuel de service

Operating Instructions and Parts Manual

Drill Press

Model: JDP-15M/MF

WMH TOOL GROUP

2420 Vantage Drive

Elgin, Illinois 60123 Part No. M-354165

Ph.: 800-274-6848 Revision A 11/03

All manuals and user guides at all-guides.com

all-guides.com

This manual has been prepared for the owner and operators of a JDP-15M/MF Drill Press. Its purpose,

aside from machine operation, is to promote safety through the use of accepted correct operating and

maintenance procedures. Completely read the safety and maintenance instructions before operating or

servicing the machine. To obtain maximum life and efficiency from your JET Drill Press, and to aid in

using the machine safely, read this manual thoroughly and follow instructions carefully.

Warranty

The WMH Tool Group warrants every product it sells. If one of our tools needs service or repair, one of

our Authorized Repair Stations located throughout the United States can give you quick service.

In most cases, any one of these WMH Tool Group Repair Stations can authorize warranty repair, assist

you in obtaining parts, or perform routine maintenance and major repair on your JET, Performax, Wilton,

or Powermatic tools.

For the name of an Authorized Repair Station in your area, please call 1-800-274-6848, or visit

www.wmhtoolgroup.com

More Information

Remember, the WMH Tool Group is consistently adding new products to the line. For complete, up-to-

date product information, check with your local WMH Tool Group distributor, or visit

www.wmhtoolgroup.com

WMH Tool Group Warranty

The WMH Tool Group (including Performax, Wilton and Powermatic brands) makes every effort to assure

that its products meet high quality and durability standards and warrants to the original retail

consumer/purchaser of our products that each product be free from defects in materials and workmanship

as follow: 1 YEAR LIMITED WARRANTY ON ALL PRODUCTS UNLESS SPECIFIED OTHERWISE.

This Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or

accidents, normal wear-and-tear, repair or alterations outside our facilities, or to a lack of maintenance.

THE WMH TOOL GROUP LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD SPECIFIED ABOVE,

FROM THE DATE THE PRODUCT WAS PURCHASED AT RETAIL. EXCEPT AS STATED HEREIN,

ANY IMPLIED WARRANTIES OR MERCHANTIBILITY AND FITNESS ARE EXCLUDED. SOME

STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS, SO THE

ABOVE LIMITATION MAY NOT APPLY TO YOU. THE WMH TOOL GROUP SHALL IN NO EVENT BE

LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL,

CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR

PRODUCTS. SOME STATES DO NOT ALLOW THE EXLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO

YOU.

To take advantage of this warranty, the product or part must be returned for examination, postage

prepaid, to an Authorized Repair Station designated by our office. Proof of purchase date and an

explanation of the complaint must accompany the merchandise. If our inspection discloses a defect, we

will either repair or replace the product, or refund the purchase price if we cannot readily and quickly

provide a repair or replacement, if you are willing to accept a refund. We will return repaired product or

replacement at WMH Tool Group’s expense, but if it is determined there is no defect, or that the defect

resulted from causes not within the scope of WMH Tool Group’s warranty, then the user must bear the

cost of storing and returning the product. This warranty gives you specific legal rights; you may also have

other rights, which vary from state to state.

The WMH Tool Group sells through distributors only. Members of the WMH Tool Group reserve the right

to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment,

which they may deem necessary for any reason whatsoever.

All manuals and user guides at all-guides.com

Table of Contents

Warranty........................................................................................................................................................ 2

More Information ....................................................................................................................................... 2

WMH Tool Group Warranty....................................................................................................................... 2

Table of Contents.......................................................................................................................................... 3

Warnings ....................................................................................................................................................... 4

Specifications ................................................................................................................................................ 6

Shipping Contents......................................................................................................................................... 7

Required Tools.............................................................................................................................................. 7

Assembly....................................................................................................................................................... 8

Before Assembly ....................................................................................................................................... 8

Column Assembly...................................................................................................................................... 8

Table Bracket ............................................................................................................................................ 8

Crank Handle and Table Lock Handle ...................................................................................................... 8

Column Lock Handle ................................................................................................................................. 9

Table Installation ....................................................................................................................................... 9

Head Assembly ......................................................................................................................................... 9

Chuck and Arbor Installation ..................................................................................................................... 9

Chuck and Arbor Removal ...................................................................................................................... 10

Adjustment .................................................................................................................................................. 10

Depth Stop Adjustment............................................................................................................................ 10

Changing Spindle Speeds....................................................................................................................... 10

Return Spring Adjustment ....................................................................................................................... 11

Work Light ............................................................................................................................................... 12

Table Tilt Adjustment............................................................................................................................... 12

Operation..................................................................................................................................................... 12

Installing Drills ......................................................................................................................................... 12

Positioning the Workpiece....................................................................................................................... 12

Using the Vise ......................................................................................................................................... 12

Basic Operation ....................................................................................................................................... 12

Maintenance................................................................................................................................................ 13

Lubrication................................................................................................................................................... 13

Electrical...................................................................................................................................................... 13

115 Volt Operation................................................................................................................................... 13

230 Volt Operation................................................................................................................................... 13

Grounding Instructions ............................................................................................................................ 14

Extension Cords ...................................................................................................................................... 14

Troubleshooting .......................................................................................................................................... 15

Exploded View Drawing JDP-15M/MF........................................................................................................ 17

Parts List JDP-15M/MF ............................................................................................................................... 18

Wiring Diagram ........................................................................................................................................... 21

JDP – 15M/MF – 115V ............................................................................................................................ 21

JDP – 15M/MF – 230V ............................................................................................................................ 21

The specifications in this manual are given as general information and are not binding. WMH Tool Group

reserves the right to effect, at any time and without prior notice, changes or alterations to parts, fittings,

and accessory equipment deemed necessary for any reason whatsoever.

All manuals and user guides at all-guides.com

Warnings

1. Read and understand the entire owners manual before attempting assembly or operation.

2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with

all of these warnings may cause serious injury.

3. Replace the warning labels if they become obscured or removed.

4. This drill press is designed and intended for use by properly trained and experienced personnel only.

If you are not familiar with the proper and safe operation of a drill press, do not use until proper

training and knowledge have been obtained.

5. Do not use this drill press for other than its intended use. If used for other purposes, WMH Tool

Group disclaims any real or implied warranty and holds itself harmless from any injury that may result

from that use.

6. Always wear approved safety glasses/face shields while using this drill press. Everyday eyeglasses

only have impact resistant lenses; they are not safety glasses.

7. Before operating this drill press, remove tie, rings, watches and other jewelry, and roll sleeves up past

the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips

are recommended. Do not wear gloves.

8. Wear ear protectors (plugs or muffs) during extended periods of operation.

9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities

contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples

of these chemicals are:

• Lead from lead based paint.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically treated lumber.

Your risk of exposure varies, depending on how often you do this type of work. To reduce your

exposure to these chemicals, work in a well-ventilated area and work with approved safety

equipment, such as face or dust masks that are specifically designed to filter out microscopic

particles.

10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

11. Make certain the switch is in the OFF position before connecting the machine to the power supply.

12. Make certain the machine is properly grounded.

13. Make all machine adjustments or maintenance with the machine unplugged from the power source.

14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting

wrenches are removed from the machine before turning it on.

15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance

purposes, use extreme caution and replace the guards immediately.

16. Make sure the drill press is firmly secured to the floor or bench before use.

17. Check damaged parts. Before further use of the machine, a guard or other part that is damaged

should be carefully checked to determine that it will operate properly and perform its intended

function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting

and any other conditions that may affect its operation. A guard or other part that is damaged should

be properly repaired or replaced.

18. Provide for adequate space surrounding work area and non-glare, overhead lighting.

19. Keep the floor around the machine clean and free of scrap material, oil and grease.

All manuals and user guides at all-guides.com

20. Keep visitors a safe distance from the work area. Keep children away.

21. Make your workshop child proof with padlocks, master switches or by removing starter keys.

22. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are

careless acts that can result in serious injury.

23. Maintain a balanced stance at all times so that you do not fall or lean against the spindle or other

moving parts. Do not overreach or use excessive force to perform any machine operation.

24. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for

which it was not designed. The right tool will do the job better and safer.

25. Use recommended accessories; improper accessories may be hazardous.

26. Maintain tools with care. Keep drill bits sharp and clean for the best and safest performance. Follow

instructions for lubricating and changing accessories.

27. Make sure the work piece is securely attached or clamped to the table. Never use your hand to hold

the work piece.

28. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do

not use your hands.

29. Do not stand on the machine. Serious injury could occur if the machine tips over.

30. Never leave the machine running unattended. Turn the power off and do not leave the machine until it

comes to a complete stop.

31. Remove loose items and unnecessary work pieces from the area before starting the machine.

Familiarize yourself with the following safety notices used in this manual:

This means that if precautions are not heeded, it may result in minor injury and/or

possible machine damage.

This means that if precautions are not heeded, it may result in serious injury or possibly

even death.

- - SAVE THESE INSTRUCTIONS - -

All manuals and user guides at all-guides.com

Specifications

Model Number: JDP-15M JDP-15MF

Stock Number ............................................... 354165.............................................. 354166

Swing............................................................. 15” .................................................... 15"

Type .............................................................. Bench ............................................... Floor

Drilling Capacity ............................................ 5/8” ................................................... 5/8”

Chuck Size .................................................... 5/8” ................................................... 5/8”

Spindle Travel ............................................... 3-1/8” ................................................ 3-1/8”

Spindle Distance to Base .............................. 16-1/2” .............................................. 48"

Spindle Distance to Table (max.).................. 24” .................................................... 29"

Table Size (Length x Width).......................... 16-1/2" x 13" ..................................... 16-1/2" x 13"

Spindle Taper................................................ MT-2/JT-3 ......................................... MT-2/JT-3

Column Diameter .......................................... 2-7/8” ................................................ 2-7/8”

Number of Spindle Speeds ........................... 16...................................................... 16

Range of Spindle Speeds (RPM).................. 200 - 3,630 ....................................... 200 - 3,630

Base Size ...................................................... 10-7/8” x 18-1/2” ............................... 11” x 19-3/4”

Overall Dimensions (H x W x D) ................... 39-1/2" x 13" x 31"............................ 63" x 13" x 31"

Motor 3/4HP, 115/230V, 60Hz, 1Ph same

Net Weight ................................................... 156 lbs. ............................................. 161 lbs.

Gross Weight ............................................... 163 lbs. ............................................. 167 lbs.

Carton Size (L x W x H/in):............................ 32 x 22 x 12 ...................................... 56 x 20 x 11

All manuals and user guides at all-guides.com

all-guides.com

Shipping Contents

Unpack the carton and verify that all parts listed

below are included.

Main Parts

1 ea Head Assembly

1 ea Table

1 set Column and Table Bracket Assembly

1 ea Base

Additional Parts

1. 1 set Chuck and Chuck Key

2. 1 pc Arbor

3. 1 pc Drift Key

4. 1 pc Table Crank Handle

5. 1 pc Table Lock Handle

6. 1 pc Column Lock Handle

7. 3 pcs Downfeed Handles and Knobs

8. 4 pcs M10 x 40 Hex Cap Screws

9. 1 set Hex Wrenches (3mm, 5mm, 6mm)

Other Material

1 ea Owner’s Manual

1 ea Warranty Registration Card

Required Tools

1. 17mm Box Wrench or a 6” – 8” Adjustable

Wrench

2. 15/16" wrench

Additional Parts

All manuals and user guides at all-guides.com

Assembly

Read and understand all assembly

instructions before attempting assembly!

Failure to comply may cause serious injury!

Before Assembly

1. Remove the contents from the shipping

container.

2. Compare the contents of the shipping

container with the list found above. Report

any shortages or damage to your JET

distributor.

3. Clean all rust protected surfaces with

kerosene or a light solvent. Do not use

lacquer thinner, paint thinner, or gasoline.

These will damage plastic components and

painted surfaces.

Column Assembly

Referring to Figure 1:

1. Place the base (A) on a level floor.

2. Place the column assembly (B) on the base

(A) and align the holes in the column

support with the holes in the base.

Note: The column shown in Figure 1 is for

the JDP-15MF. While the JDP-15M column

is slightly different in appearance, the

assembly procedure is the same.

3. Using a 17mm wrench, secure the column

(B) with four M10 x 40 hex cap screws (C) to

the base.

Figure 1

Table Bracket

When shipped, the rack ring and rack are

bundled together with the column in plastic

wrap.

Referring to Figures 2 and 3:

4. Remove the wrap and take the rack ring (D)

and rack (B) off the column (C).

5. Install the table bracket (A) together with the

rack (B) as shown in Figure 2.

Figure 2

6. Slide the rack ring (D) over the column (C),

placing it so it rests against the rack (B) as

shown in Figure 3 and tighten firmly.

Figure 3

Crank Handle and Table Lock Handle

Referring to Figure 4 (shown already

assembled):

1. Loosen the setscrew (B) on the table crank

handle (A).

2. Slide the handle (A) onto the table bracket

shaft.

3. Turn the handle until the setscrew is

opposite the flat section on the shaft, and

tighten the setscrew to secure the handle.

4. Install the table lock handle (C), but do not

tighten.

All manuals and user guides at all-guides.com

Figure 4

Column Lock Handle

Referring to Figure 5:

Thread the column lock handle (D) into the table

bracket (E).

Figure 5

Table Installation

Referring to Figure 6:

1. Place the table (A) on the bracket (B).

2. Tighten the table lock handle (C).

Figure 6

Head Assembly

Referring to Figure 7:

1. With the aid of a second person, carefully lift

the head onto the column top and slide it

down into position

The head assembly is heavy! Use care when

lifting onto the column!

2. Rotate head assembly until sides of the

pulley cover are parallel with the sides of the

base.

3. Tighten two setscrews (A) with a 5mm hex

wrench (provided) until they are snug.

Figure 7

4. Install three downfeed handles (B) into the

downfeed hub (C).

Chuck and Arbor Installation

Referring to Figure 8:

1. Twist the chuck (B) to retract the chuck jaws

if they are exposed.

2. Install the chuck (B) to the arbor (A) tightly.

3. Insert the chuck and arbor assembly into the

spindle (C). Pull the downfeed handle down

to press the arbor in place.

Note: Put a piece of scrap wood (D) on the table

to protect the chuck nose when pulling the

downfeed handle (E) down to press into place.

All manuals and user guides at all-guides.com

Figure 8

Chuck and Arbor Removal

Referring to Figure 9:

1. Unplug machine from the power source.

2. Raise the table until it is about seven inches

below the chuck.

3. Place a piece of scrap wood on the table,

and lower quill (A) using the downfeed

handle.

4. Rotate spindle to align the keyhole in the

spindle with the keyhole in the quill.

5. Insert the drift key (B) into the aligned slots

and tap lightly. The chuck and arbor

assembly should fall from the spindle.

Figure 9

Adjustment

Depth Stop Adjustment

Referring to Figure 10:

To drill multiple holes at the same preset depth,

use the depth stop:

1. Use a pencil to mark the depth the bit will

drill into the workpiece.

2. With the drill bit in the chuck, lower

downfeed handle to advance bit to your

mark (A).

3. With your other hand, advance the lock nuts

(B) on the depth stop rod until they are snug

to the seat (C).

4. The drill bit will now advance to this point.

5. To release, advance the nuts counter-

clockwise to the top of the depth stop.

Figure 10

Changing Spindle Speeds

A spindle speed and pulley/belt arrangement

chart is found on the inside of the pulley cover

(D, Fig. 11). The chart is also shown in Figure

12. Refer to this chart whenever changing

speeds.

To change spindle speeds:

1. Unplug the machine from the power source.

2. Loosen two bar knobs (E, Fig. 11) found on

each side of the head assembly.

3. Rotate the tension adjuster clockwise (F,

Fig. 11) to bring the motor base as close to

the head as possible.

4. For desired speed, change the location of

belts per pulley/belt arrangement chart.

5. Rotate the tension adjuster

counterclockwise (F. Fig. 11) to tension the

belts.

All manuals and user guides at all-guides.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels WMH Tool Group Outils électriques

WMH Tool Group

WMH Tool Group Powermatic PJ1696T Manuel de service

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel