Wiznet WIZ630wi Manuel utilisateur
© Copyright 2012 WIZnet Co., Inc. All rights reserved. 1
WIZ630wi User Manual
(Version 0.93)
© 2012 WIZnet Co., Inc. All Rights Reserved.
For more information, please visit our website at http://www.wiznet.co.kr
© Copyright 2012 WIZnet Co., Inc. All rights reserved. 2
Certification Information
CE for Class B ITE
INFORMATION TO THE USER
Hereby, WIZnet. Declares that this WIZ630wi is in compliance with the essential requirements and other
relevant provisions of directive 1999/5/EC.
WARNING: This is a class B product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
FCC for Class B ITE
INFORMATION TO THE USER
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
Guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
© Copyright 2012 WIZnet Co., Inc. All rights reserved. 3
Connecting the Web page of WIZ610wi
Some items may be not supported depending on the version.
Web address
Open a web browser on user’s PC. Input the default IP address of WIZ630wi, “192.168.16.254” and
click Enter.
Web Login
A pop up will request user to input User ID and Password
User ID: admin / Password: admin
The system’s basic information, as shown below, will appear if successfully authenticated.
© Copyright 2012 WIZnet Co., Inc. All rights reserved. 4
Type Description
F/W Version The firmware version of WIZ630wi is displayed.
System Up Time System up time displayed.
Operation Mode System operation mode displayed.
Internet Configuration Information of the external network is displayed.
Local Network Information of the Local network is displayed.
Ethernet Port Status Link of LAN Port status is displayed.
© Copyright 2012 WIZnet Co., Inc. All rights reserved. 5
Wireless Specifications
Type Description
Wireless Standard IEEE802.11b/g/n
Frequency Range
USA: 2.400 ~ 2.483GHz
Europe: 2.400 ~ 2.483GHz
Japan: 2.400 ~ 2.497GHz
China: 2.400 ~ 2.483GHz
Operating Channels
USA/Canada: 11(1 ~ 11)
Major Europe Countries: 13(1 ~ 13)
France: 4(10 ~ 13)
Japan: 14 for 802.11b(1 ~ 14), 13 for 802.11g(1 ~ 13)
Korea/China: 13(1 ~ 13)
Output Power
(Tolerance(+/-1dBm)
802.11b: 9.88dBm@11Mbps
802.11g: 7.44dBm@54Mbps
802.11n(20MHz): 8.08dBm@72Mbps
802.11n(40MHz): 4.83dBm@150Mbps
Receive Sensitivity
802.11b: -89dBm@11Mbps
802.11g: -74dBm@54Mbps
802.11n(20MHz): -70dBm@72Mbps
802.11n(40MHz): -66dBm@150Mbps
Data Rates
802.11b: 1,2,5.5,11Mbps
802.11g: 6,9,12,18,24,36,48,54Mbps
802.11n(20MHz): 7,14.5,21.5,28.5,43.5,57.5,65,72Mbps
802.11n(40MHz): 29.5,86.5,115,130,144,150Mbps
Modulation Type 11g: OFDM(64QAM, 16QAM, QPSK, BPSK)
11b: DSS(CCK, DQPSK, DBPSK)
Operation Distance
802.11b
Outdoor: 150m@11Mbps, 300m@1Mbps
Indoor: 30m@11Mbps, 100m@1Mbps
802.11g
Outdoor: 50m@54Mbps, 300m@6Mbps
Indoor: 30m@54Mbps, 100m@6Mbps
802.11n
Outdoor: 30m@150Mbps, 250m@7Mbps
Indoor: 20m@150mbps, 100m@7Mbps
Dimension 33mm X 43mm X 4.5mm
© Copyright 2012 WIZnet Co., Inc. All rights reserved. 6
1. Operation mode
User can select the operation mode.
The default setting of WIZ630wi is AP Mode. (DHCP Server Enabled)
Access Point (Bridge)
In this mode, all Ethernet ports and wireless interface are bridged together. Wired/Wireless interface
has the same IP address space with its top mesh. DHCP Server function is disabled and WIZ630wi
does not assign an IP. Wireless (LAN Port included) sending periodic Broadcast Packet to Station and
maintains a connection with Station.
Gateway (Router)
Operate in router mode. Interfaces are separated into WAN I/F (Top Internet Business Network), LAN
I/F (Sub Private Network: 192.168.16.xxx), Wireless I/F (Sub Private Network: 192.168.16.xxx). Port # 0
will be assigned to the WAN Port. WIZ630wi periodically sends Broadcast Packet to Sub-LAN (LAN
Port included) and maintains connection with Station.
Client (Station)
Wireless I/F is assigned as WAN Port and all Ethernet Ports are bound to LAN Port. Set the profile and
the WIZ630wi is automatically connected to the AP when re-booting in the future. Devices that are
connected through the LAN port are assigned a private IP. WIZ630wi periodically sends PING Packet
to AP Gateway and maintains connection with AP.
AP-Client mode
Wireless I/F is assigned as WAN Port and all Ethernet Ports are bound to LAN Port. This mode is
similar to Station mode, however the difference is that the Wireless I/F will operate as client with AP
simultaneously. WIZ630wi periodically sends Broadcast Packet to Sub-LAN (LAN Port included) and
maintains connection with Station.
© Copyright 2012 WIZnet Co., Inc. All rights reserved. 7
ad-hoc mode
This mode is similar to Gateway mode. The Wireless I/F operates as ad-hoc and connects to Station
Point-to-Point. There is no communication between the LAN Port and Wireless I/F (ad-hoc).
WAN ad-hoc: OK
WAN LAN: OK
ad-hoc ad-hoc: OK
ad-hoc LAN: No Communication
2. Internet Setting
3.1 Internet connection setting
Select the internet service type and WIZ630wi can connect to the internet
If users would like to access to Internet, Gateway Mode should be selected.
Type Description
WAN Connection
Type
Select the communication ways for Internet’s connection
-Static(Fixed IP)
-DHCP (Auto config)
-PPPoE
Host Name Settings about module’s host name
Mac Clone Some ISPs require that you register a MAC address. Users can directly enter MAC address
or use the MAC Clone function.
© Copyright 2012 WIZnet Co., Inc. All rights reserved. 8
Type Description
DHCP(Auto
config)
User should choose DHCP Mode when the user connects to the internet service such as
FTTH, cable modems, VDSL, IP-ADSL.
Static(Fixed IP)
Static IP setting window. If user receives static IP from ISP, user should set the Fixed IP .
Input the network information that got from ISP
(such as IP, Subnet, Gateway, DNS)
PPPoE(ADSL)
-. User Name: Setting the User Name received from ISP
-. Password: Password assigned by the internet service company
-. Operation Mode: This mode is used for re-connecting when connection is bad.
© Copyright 2012 WIZnet Co., Inc. All rights reserved. 9
3.2 Local network setting
WIZ630wi internal IP setting, DHCP server setting and DHCP.
Type Description
IP Address Enter the module’s IP. (Basic Value : 192.168.16.254 )
Subnet Mask Enter the module’s Subnet Mask .
MAC Address MAC Address of module’s LAN port (Wireless included). (Read Only)
DHCP Server Decide whether the module’s DHCP server will be used.
Start IP Address Set the start IP address that will be assigned from the DHCP server
End IP Address Set the end IP address that will be assigned from the DHCP server.
Subnet Mask Enter the value of subnet mask.
Primary DNS Server Enter the primary DNS server address.
Secondary DNS Server Enter the secondary DNS server.
Lease Time Enter the lease time when IP address is assigned.
Statically Assigned Maximum of three IP can be statically assigned when IP address is
assigned.
© Copyright 2012 WIZnet Co., Inc. All rights reserved. 10
3.3 DHCP Client Information
The IP information that is assigned from the DHCP server is shown.
Type Description
Host name Client’s host name is shown
Mac Address Client’s MAC address is shown.
IP Address Client’s IP address is shown.
Expires in The usable time of client’s IP address is shown.
3.4 VPN setting
This section will explain on VPN packet settings.
Type Description
L2TP Pass-through Enable : VPN L2TP packet is passed through WAN.
Disable : VPN L2TP packet is not passed through WAN. (Default value)
IPSec Pass-through Enable : VPN IPSec packet is passed though WAN.
Disable : VPN IPSec packet is not passed through WAN. (Default value)
PPTP Pass-through Enable : VPN PPTP packet is passed through WAN.
Disable : VPN PPTP packet is not passed through WAN. (Default value)
Autres manuels pour WIZ630wi
2
Table des matières
Autres manuels Wiznet Routeur sans fil
Wiznet
Wiznet WizFi320 Manuel utilisateur
Wiznet
Wiznet WizFi630S Manuel utilisateur
Wiznet
Wiznet WizFi630 Manuel utilisateur
Wiznet
Wiznet WizFi630 Instructions d'installation
Wiznet
Wiznet WizFi360 Series Instructions de montage
Wiznet
Wiznet WizFi250 Manuel
Wiznet
Wiznet WizFi360 Series Manuel utilisateur
Wiznet
Wiznet WizFi360 Series Mode d’emploi
Wiznet
Wiznet WizFi210 Manuel utilisateur
Wiznet
Wiznet WizFi360 Series Guide de configuration
