Wirepath Surveillance WPS-MNT-EXT-DOM Manuel utilisateur
WPS-MNT-EXT-DOM Dome Camera Extension Mount
Introduction
© 2012 Wirepath™ Surveillance
pg. 1
Installation Guidelines
Parts Included
Mounting
When mounting to a junction box, we recommend the use of metal boxes, doing so will provide the
most secure installation.
Weatherproong
While grommets and gaskets are provided to help block out moisture, we recommend that the
installation is completed with silicone on external connections and mount to junction box mating
surfaces. This will help ensure that moisture will not enter the wall.
A. (1) Dome Extension Mount
Not Shown
B. (2) #6-32x3/4”L - Flat Head Philips
C. (2) #8-32x3/4”L - Flat Head Philips
D. (3) M4x25L - Round Head Philips with rubber
washers
E. (1) Manual
Designed to simplify installation and overcome complexity of where to terminate connections, this
mount will t a variety of metal junction boxes both interior and exterior weatherized boxes:
• Single
• Double
• 4” Octagon
• 4” Octagon
• 3-4” Cieling Fan Box
• 3/4” Conduit (Interior Only Locations)
Installation Manual
A
www.snapav.com Support: 866.838.5052
pg. 2
WPS-MNT-EXT-DOM Installation Manual
Installation
Important Note: To avoid damaging the dome surface during installation, keep the dome surface
away from walls and other objects. Do not remove the protective coating from the dome until
after the camera is mounted and the dome installed.
Microfiber or similar cloths can be abrasive, only use a dry eyeglasses cloth when cleaning the
lens to avoid damage that can blur the cameras image.
1. Attach the Extension Mount
Plate Mounting Holes
The Extension Mount is designed to t a variety of junction box sizes. See the diagram below for the various
junction box sizes.
Junction Box Mounting
A. Run the wires from the installation position
through the center hole in the Extension
Mount.
B. Secure the extension mount to the junction
box or eve using the appropriate screw
locations. See Plate Mounting Holes for details
on the various locations available.
A. Single Gang
B. Double Gang
C. 4” Square
D. 4” Square if (4” Square Box is rotated)
E. 3” Octagon
F. 4” Octagon / Ceilling Fan
A
A
B
B
C
D
D
C
B
B
E EF F
Figure 1
© 2012 Wirepath™ Surveillance
pg. 3
WPS-MNT-EXT-DOM Installation Manual
Conduit Mounting (3/4”)
A. Remove the dome from the Camera Base
using the 3mm Allan key supplied with the
camera. Avoid contact of the dome with
surfaces in order to avoid scratching the
material.
B. Connect the wires from the junction box or
conduit to the Cameras wires.
C. Align the mounting holes in the camera base
with the with the camera screw locations.
Tip: Inserting a mounting screw into the Camera
Base and then into the Dome Extension Mount
speeds up the alignment process.
Note: To avoid moisture from entering the
camera; ensure that the rubber grommets are
on the screws during installation.
D. Secure the Camera Base to the Dome
Extension Mount (A) using all 3 provided
M4x25L - Round Head Philips (D) screws with
rubber washers.
E. Loosely re-attach the dome cover onto the Camera base. Note that you will need to remove the
dome cover later to setup the camera once it is fully mounted.
A. Using a utility knife, remove the center part of the gasket located on the rear of the Extension
Mount. This allow for easy installation of the conduit into the mount. (Figure 2)
B. Run the wires from the Conduit through the center hole in the Extension Mount. (Figure 3)
C. Secure the Mount to the conduit by rotating clockwise.
The WPS-MNT-EXT-DOM can also be used for commercial installations where mounting to the end of
threaded conduit is desired. This type of installation is for indoor use only, do not use this method for
outdoor cameras.
Remove
Figure 2 Figure 3
2. Attach the Camera to the Mount
Figure 4
Note: Internal camera components removed for
demo purposes. DO NOT disassemble the camera.
WPS-MNT-EXT-DOM Installation Manual
5. Finalize the Installation (outdoor cameras)
6. Setup the Camera
For outdoor installations, we recommend adding a bead of silicone around the edges of the mount.
This will help ensure that moisture will not enter the wall.
Now that the camera is mounted, it can be setup for angle, zoom, and focus. Follow the instructions in
the manual for the Wirepath™ Surveillance camera that has been installed.
© 2012 Wirepath™ Surveillance
120829-1620
Contacting Technical Support
Phone: (866) 838-5052
Email: [email protected]
Table des matières
Autres manuels Wirepath Surveillance Accessoires pour appareils photo
