Windster WS-68N30SS Manuel utilisateur
www.windsterhood.com
User’s Manual
WS-68N30SS
WS-68N36SS
WS-68N42SS
Please read this operation manual thoroughly before
using your range hood. Store it in a safe location for
when you need to reference it in the future.
NOTE: PLEASE INSPECT HOOD
IMMEDIATELY UPON RECEIVING.
CLAIM OF DAMAGE AFTER 7 DAYS
OF DELIVERY WILL BE DENIED.
This unit is designed for indoor
residential use only. DO NOT USE
OVER A WOOD GRILL OR MOUNT
IN OUTDOOR ENVIRONMENT.
ISLAND SERIES
1
TABLE OF CONTENTS
Table of Contents
Safety Information ..............................................................2 –3
Content Checklist .....................................................................4
Measurements ...........................................................................5
Preparation ................................................................................6
Installation ...........................................................................7 –8
Installation Diagram...................................................................9
Operation & Features .............................................................10
Cleaning & Maintenance .........................................................11
Troubleshooting ......................................................................12
Part List / Replacement / Wiring Diagram .............................13
Warranty / Contact Us .....................................................14 –15
2
SAFETY INFORMATION
SAFETY INFORMATION
TO REDUCE THE RISK OF A FIRE, ELECTRICAL SHOCK,
AND/OR INJURY OBSERVE THE FOLLOWING:
Unit is intended for indoor residential use only. If you should have questions,
contact the manufacturer at the address or telephone number listed in the
warranty.
In case the unit should need to be cleaned or repaired, switch power off at
service panel and lock service disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a prominent warning device, such as a tag, to the
service panel.
Installation work and electrical wiring must be done by a qualified technician in
accordance with all applicable codes and standards, including fire-rated
construction.
Sufficient air is needed for proper combustion and exhausting of gases
through the flue (chimney) of fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s guideline and safety standards
such as those published by the National Fire Protection Association (NFPA),
and the American Society of Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code authorities.
Because the unit is made of stainless steel, it may contain sharp edges. Be
careful to avoid cuts and abrasions by wearing protective gloves during
installation and cleaning.
Before you begin to cut or drill into the wall, verify that there is no electrical
wiring or any other hidden electrical components.
Ducted fans must always be vented to the outdoors.
The unit must be properly grounded and installed at the recommended height
before beginning operation.
To reduce the risk of fire, use only metal ductwork.
CAUTION: FOR GENERAL VENTILATING USE ONLY. DO NOT
USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS
AND VAPORS
3
SAFETY INFORMATION
TO REDUCE THE RISK OF FIRE, OR ELECTRIC SHOCK, DO NOT
USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE.
Regardless of heat level, never leave any surface materials unattended while
operating an open flame.
Always turn hood ON when cooking at high heat or when flambéing food (i.e.
Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
Depending on amount of usage, clean ventilating fans and filters frequently.
Grease should not be allowed to accumulate on fan or filter. For instructions
on the how to clean, see maintenance page.
Never leave surface units unattended at high settings. Boil-overs may cause
smoking and greasy spillovers may ignite as result. Heat oils slowly on low or
medium settings.
Use proper pan size. Always use cookware appropriate for the size of the
surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWING:
SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then
turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not
go out immediately, EVACUATE AND CALL 911.
NEVER PICK UP A FLAMING PAN —Doing so may result in serious burns
and possibly spread the fire.
DO NOT USE WATER –Grease fire must be extinguished before further
action may be taken. Using water will agitate the grease and may cause a
violent steam explosion.
Use a Fire Extinguisher ONLY if:
You know you have a Class ABC extinguisher, and you already know
how to operate it.
The fire is small and contained in the area where it started.
The fire department is being called.
You are able to safely control the fire with your back to an open exit. *
Based on ―Kitchen Fire safety Tips‖ published by NFPA.
4
CONTENT CHECKLIST
CONTENT CHECKLIST
1. CONTENTS INCLUDED
a. (1) WS68-N series (30‖, 36‖ or 42‖) hood assembly
b. (1) Lower duct cover (16-1/2‖)
c. (1) upper duct cover (22-3/4‖)
d. (1) User’s manual
e. (1) 7‖ Damper transition adapter collar
f. (1) Aluminum Filter (30‖ model)
g. (2) Aluminum Filters (36‖/42‖ model)
h. (1) Screw packet
i. (1) Duct cover support bracket
2. CONTENTS NOT INCLUDED
a. WS68-NLDC (Long duct cover)
b. WS68-NSDC (Special duct cover)
c. WS68-NBF (Baffle filter)
d. WS68-NDK (Ductless kit)
e. WS68-NCF (Charcoal filter)
f. WS68-NCFMR (CFM reducer)
g. 7‖ Aluminum or metal piping
3. TOOLS REQUIRED (NOT INCLUDED)
a. Safety gloves
b. Safety glasses
c. Electric drill w/ starter bit
d. Utility knife
e. Spirit level
f. Measuring tape
g. Writing instrument (pen, marker, pencil)
h. Aluminum tape
5
MEASUREMENTS
6
PREPARATION
PREPARATION
1. BEFORE YOU START
**BE SURE YOUR UNIT WILL FIT YOUR CEILING HEIGHT**
**DO NOT INSTALL IF DAMAGED**
**RETURN OR EXCHANGE WILL BE DENIED IF INSTALLED**
a. Be sure you have all the content of your purchase and required tools for
this installation.
b. Installation may take at least 2 to 3 hours from start to finish.
c. Plan to use as few elbows or turns as possible for more efficient air flow.
d. Collar size may need to be increased if utilizing a long duct run.
e. Turns must be made after passing ceiling.
f. Do not try to install this unit by yourself, SERIOUS INJURY MAY OCCUR.
g. At least two people are needed for installation.
h. Hiring a certified installer and electrician is recommended.
2. LOCATION
**THIS MODEL MAY NOT FIT ALL CEILING HEIGHTS**
a. Determine the exact location you where want to install the range hood.
b. Recommended distance between cooktop and range hood is 28‖ –33‖.
c. Range hood should be mounted at stated measurements to ensure
performance and lifespan of electrical components.
d. Correctly measure the dimension needed to install the unit.
3. HOOD
a. Inspect for any sign of defect or damage. (ie. scratches, dents, loose
seams, etc.)
b. Power up the unit to make sure it is working properly.
Use Fig. 1a and 1b on page 5 for measurements
INSTALLATION
7
INSTALLATION
1. STANDARD INSTALLATION
a. Make sure all preparation steps are completed.
b. Determine your ceiling height to see if you need an extension.
i. Hood unit (with glass) height = 3-1/4‖ (30‖ model only)
ii. Hood unit (with glass) height = 4-1/4‖ (36‖ model only)
iii. Hood unit (with glass) height = 6‖ (42‖ model only)
iv. Standard DC height = 16-1/2‖ (lower) + 22-7/8‖ (upper)
v. Minimum height (Standard duct cover only) = 24-3/4‖
vi. Minimum height (Standard duct cover w/ DK) = 24-3/4‖
vii. Maximum height (Standard duct cover only) = 38-5/8‖
viii. (OPTIONAL) WS-68NLDC height = 22-7/8‖ (lower) + 36-1/4‖ (upper)
ix. (OPTIONAL) Long DC minimum height = 40‖
x. (OPTIONAL) Long DC maximum height = 55-1/8‖
xi. (OPTIONAL) WS-68NSDC height = 36-3/16‖ (lower) + 39-1/4‖
(upper)
xii. (OPTIONAL) Special DC Minimum height = 42-3/16‖
xiii. (OPTIONAL) Special DC Maximum height = 75-1/4‖
xiv. Standard Installation = Hood + standard DC
xv. 9’ – 11’ Installation = Hood + Long DC
xvi. 11’ – 12’ Installation = Hood + Special DC
c. Determine the location you want to install the range hood. (Fig. 2a)
d. Prepare ceiling and locate wood support.
e. Mount the unit upper support frame to the ceiling.
f. Cut a 7‖ round opening at the ceiling for ducting pipe.
g. Adjust the (4) arms to desired height. (Fig. 2b)
h. Attach upper duct cover to upper support frame.
i. Use a spirit level to ensure the balance of the support frame is true.
j. Slide lower duct cover toward ceiling and hold. (Fig. 2c)
k. Install ducting through the ceiling.
l. Secure hood from all sides with the (8) screws. (Fig. 2d)
m. Installation is complete when hood is securely in place. (Fig. 2e)
8
INSTALLATION
2. EXTENSION INSTALLATION (OPTIONAL)
a. AFTER COMPLETING STEP A –D OF STANDARD INSTALLATION,
replace the standard support frame and duct cover with either the
extension set or the short duct cover set.
b. REPEAT “STEP F – M” from STANDARD INSTALLATION.
3. COLD WEATHER INSTALLATION (OPTIONAL)
a. Check with your local building codes to see if a CFM reducer is an
acceptable alternative to make-up air.
b. Remove the WS68-NCFMR (CFM Reducer) and inspect for any sign of
defect or damage. (ie. Cracks, broken flips)
c. AFTER COMPLETING Step A –J of STANDARD INSTALLATION,
place the CFM reducer onto the outlet of the unit and seal the connection
point with aluminum tape. (Be sure it is secure with no opening or gaps)
d. Connect piping to the outlet of the hood.
e. Installation is complete when hood is securely in place.
4. DUCTLESS INSTALLATION (OPTIONAL)
a. AFTER COMPLETING Step A –E of STANDARD INSTALLATION
b. Remove the WS68-NDK (ductless kit) and inspect for any sign of defect
or damage. (ie. dents, broken inlet)
c. Attach the ductless kit to the support frame and secure with screws.
d. Install the upper duct cover and secure it to the support frame.
e. Slide the lower duct cover up to the upper duct cover and hold in place.
f. Connect a 6‖ or 7‖ pipe between the ductless kit and the hood outlet.
g. REPEAT “STEP G – M” from STANDARD INSTALLATION.
Installation diagram available on next page
9
INSTALLATION DIAGRAM
INSTALLATION DIAGRAM
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Windster hotte de ventilation
Windster
Windster RA-3030SS Manuel utilisateur
Windster
Windster WINT024 Instructions de montage
Windster
Windster RA34LU30SS Manuel utilisateur
Windster
Windster WS-3230SS Manuel utilisateur
Windster
Windster WS-208F Manuel utilisateur
Windster
Windster RA-1730 Manuel utilisateur
Windster
Windster H30SS Manuel utilisateur
Windster
Windster WS-38U30SS Manuel utilisateur
Windster
Windster WSC-4630SS Manuel utilisateur
Windster
Windster H30SS Manuel utilisateur
Windster
Windster WS-50E Series Manuel utilisateur
Windster
Windster WS-96TB Manuel utilisateur
Windster
Windster WS-6730SS Manuel utilisateur
Windster
Windster ISLAND Series Manuel utilisateur
Windster
Windster RA34LU30SS Manuel utilisateur
Windster
Windster RA-3030 Manuel utilisateur
Windster
Windster WS-62N Series Manuel utilisateur
Windster
Windster WS-5830SS Manuel utilisateur
Windster
Windster RA-239036SS Manuel utilisateur
Windster
Windster ISLAND Series Manuel utilisateur
