WilTec 51487 Manuel utilisateur

Operation Manual

51487

Read and follow the operating instructions and safet information before using for the first time.

Technical changes reserved!

Due to further developments, illustrations, functioning steps and technical data can differ

insignificantl .

Updating the documentation

If ou have suggestions for improvement or have found an irregularities please contact us.

http //www.WilTec.de

http //www.aoyue.eu

http //www.teichtip.de

The information contained in this document is subject to change without prior notice. No part of this

document can be copied or duplicated in another form without the prior written consent of WilTec

Wildanger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liabilit for an errors in

this user manual or the connection diagram.

Although WilTec Wildanger Technik GmbH has made ever effort to make sure that this user manual is

complete, accurate and updated, errors cannot alwa s be avoided. In the event of problems with this

user manual please complete and send this form back to us.

FAX-notification (+++49 2403 55592-15),

from ________________________________________

Name ________________

Firm _____________________

Tel/Fax __________________

I would like to report the following mistakes

_______________________________ ____________________________________

Customer Service WilTec Wildanger Technik GmbH

e-mail: service@WilTec.info

Tel:++ +49 2403 55592-0

Introduction

Thank ou for purchasing this qualit product. To minimize the risk of injury by means of fire or

electric shock we urge that our clients take some basic safety precautions when using this

device. Please read the operation instructions carefully and make sure you have understood its

content.

Always use a grounded power connection with the appropriate mains voltage. You can

nd the corresponding mains voltage on the type plate. If you have any doubts about the

connection being grounded, have it checked by a qualied professional. ever use a

faulty electric cable.

Do not inspect the electrical part of the pressure pond lter in a wet or damp environment

or when you are wet yourself and protect it from direct sunlight. Install this device in a

safe location so that nobody can step on the cable, fall over or damage it. Disconnect the

power plug before cleaning it and use only a damp cloth for cleaning. Avoid using

cleaning agents and make sure that no liquid enters the electrical part of the pump.

The electric part of the device contains no parts that can be inspected or serviced b the user. Leave

the maintenance, adjustment and repair to qualified technical personnel. In case of unauthorised

intervention the 2- ear warrant is no longer valid! Keep these operation instructions safe.

http //www.WilTec.de

http //www.aoyue.eu

http //www.teichtip.de

This new digital flowmeter is suitable for filling stations as well as industrial and private use. The instal-

lation of the flowmeter is eas and without much effort. Cleaning and maintenance is possible without

much effort. The meter is intended for use in different countries. It is adjustable in four different units,

such as Liters (L) / Gallons (GAL) / Pints (PT) / Quarts (QT). The power suppl is ensured b two inter-

nal batteries (AAA).

Technical specifications

Connection BSPT / NPT 1“

Maximum pressure 0,25 MPa

Accurac ± 0,5%

Flow rate 38 – 380 l/min

Allowed media diesel, kerosene, gasoline

Temperature range -10~+60℃

Batter 2 x AAA

Stand-B Time Batter Ca. 2 ears

LCD displa Displa 6 digits

How it works

Reset counter to "0"

To reset the displa to 0, press and hold the "DISPLAY" button for one second.

Total Display

When ou press the "CALIBRATE" button, the total displa is displa ed. If this screen has reached a

total of 999,999, it is automaticall reset to 0.

Calibrate settings

Press and hold the "CALIBRATE" button for 3 seconds. Press "DISPLAY" or "CALIBRATE" for the de-

sired setting.

The displa is programmed so that the digital flowmeter returns to standb mode after 5 seconds of in-

activit .

Setting the unit

Press and hold the "CALIBRATE" button for 3 seconds. Now press the "DISPLAY" button five times,

and then press the "CALIBRATE" button to select from the various units.

Liters (L) / Gallons (GAL) / Pints (PT) / Quarts (QT)

Maintenance

The measuring instrument is almost maintenance-free. However, it is important that the rotor is free to

move. Keep the meter clean and free of impurities. If the rotor does not rotate freel , appl a penetra-

ting lubricant to the rotor, shaft and bearings. Remove an foreign objects or deposits from the rotor

with a soft brush or small sonde. Ensure that the turbine rotor or the turbines are not damaged.

Replace the batteries when "L Bat" is displa ed.

To ensure accurate readings, make sure that there is no air in the s stem and the minimum flow rate is

ensured.

http //www.WilTec.de

http //www.aoyue.eu

http //www.teichtip.de

Disposal regulations

EU guidelines regarding the disposal of scrap electric appliances (WEEE, 2002/96/EC) were

implemented in the law related to electrical and electronic equipment and appliances.

All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out

wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the

domestic waste.

The compan WilTec Technik GmbH has been registrated in the German registr EAR under the

WEEE-registration number DE45283704.

Disposal of used electrical and electronic appliances

(intended for use in the countries of the European

Union and other European countries with a separate

collection s stem for these appliances).

The logo on the article or on its packaging points out

that this article must not be treated as normal

household waste but must be disposed to a rec cling

collection point for electronic and electrical waste

equipment. B contributing to the correct disposal of

this article ou protect the environment and the health

of our fellow men. Environment and health are

threatened b inappropriate disposal.

Materials’ rec cling helps reduce the consumption of raw materials.

Additional information on rec cling this article can be provided b our local communit , municipal

waste disposal facilities or the store where ou purchased the article.

Address:

WilTec Wildanger Technik GmbH

Königsbenden 12 / 28

D-52249 Eschweiler

Important notice:

The reprint or reproduction, even of excerpts, and an commercial use, even in part of this instructions

manual require the written permission of WilTec Wildanger Technik GmbH.

http //www.WilTec.de

http //www.aoyue.eu

http //www.teichtip.de

Table des matières

Autres manuels WilTec Instrument de mesure

WilTec

WilTec naturewater 50810 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur