Weil-McLain SB0002 Manuel de service

In an effort to provide the industry with the best available technology for clean efficient

combustion of fuel oil, Weil-McLain has standardized the GOLD Oil boiler burner control offering

to include the Carlin 60200-02 primary control and 14,000 volt solid state ignitor. Listed below

are some helpful tips for understanding these new controls.

Carlin 60200-02 Primary Control Standard Features / Benefits:

♦Interrupted Duty – Turns off the ignition ignitor once the flame is established reducing

energy consumption and minimizing component wear.

♦Self-Diagnostic Check – On each call for heat, control performs a 4-second check of

internal circuitry. Helps prevent burner runaway in the event of a welded set of motor

contacts.

♦10 Second Valve-On-Delay (Prepurge) – Allows the burner motor and fuel oil pump to

come fully up to speed and pressure prior to opening the oil solenoid valve and igniting the

oil which provides cleaner startups.

♦10 Second Motor-Off-Delay (Postpurge) – Closes solenoid valve cutting off fuel supply

while keeping the motor and blower on to complete combustion process, virtually eliminating

smoke on shutdown.

♦15 Second Trial For Ignition – If oil fails to ignite in the first 15 seconds, control will lock out

reducing potential for oil soaked chambers.

♦Flame Stabilization Period – Ignitor / spark remains on for 10 seconds after trial for ignition

period ends.

♦Recycle – If control detects a flame failure, the burner will shut off in 1.3 seconds after loss

of flame and then automatically commence with a 65-second recycle period after which

control will go through another trial for ignition cycle.

♦Latch up – If control sees 3 consecutive lock-outs on the same call for heat, control will

enter latch-up potentially eliminating flooded chambers from repeated homeowner attempts

of pushing reset button.

♦Alarm Contacts – Close when control is in a lock-out or latch-up condition. Control may be

connected to a separate security system for notification of a no heat situation.

♦Warranty – 3 years.

Primary Control Sequence of Operation:

1. Call for heat initiated.

2. Microprocessor performs a 4-second diagnostic self-check of internal control circuitry.

3. 1-second pre-ignition (ignitor energized with spark on).

4. 10-second valve-on-delay (prepurge).

5. Solenoid valve is energized allowing fuel to flow to nozzle and spark.

6. 15-second trial for ignition. If no flame is established, control will lock out after 15

seconds.

Number: SB0002

(Page 1 of 2)

Date: February 2, 2000

Subject: GOLD Oil Boiler Primary Burner Controls #60200-02

Technical Services Bulletin No: SB0002 (Page 2 of 2)

Subject: GOLD Oil Boiler Primary Burner Controls #60200-02

Date: February 2, 2000

7. 10-second flame stabilization period (flame established / spark remains on). If flame is

established and extinguished, the control detects a flame failure and will shut off the fuel

supply within 1.3 seconds. The control then enters a 65-second recycle period. After 65

seconds, the control returns to the call for heat and begins another diagnostic self-check.

8. Ignitor shuts off (spark off) – burner is now in normal cycle.

9. Call for heat is satisfied. Solenoid valve is deenergized extinguishing flame.

10. 10-second motor-off-delay (postpurge).

11. Burner off.

Primary Control LED Status Indicators:

♦Amber Light “On Steady”: Control is conducting a 4-second diagnostic self-check of

internal circuitry.

♦Amber Light “Flashing”: Control has detected a failure in the diagnostic self-check.

♦Red Light “On Steady”: Control is in lock-out. Reset button must be depressed for 1

second to remove from lock-out condition.

♦Red Light “Flashing”: Control is in recycle. Control has detected a loss of flame during

the run cycle. Burner is off and control is performing a 65-second recycle after which the

burner begins sequence of operation over and will try again for ignition.

♦Red and Amber Lights “On Steady”: Control is in latch-up. The control has experienced

3 consecutive lock-outs in one call for heat. To remove from latch-up, depress the reset

button for 30 continuous seconds. After 10 seconds of depressing the reset button, the red

and amber lights will begin to flash alternately for the remaining 20 seconds. After

depressing the reset button for the full 30 seconds, the red and amber lights will go out.

Remove your finger from the reset button and the control will return to “call for heat” position.

Carlin CCT4100 14,000-Volt Solid State Ignitor Standard Features / Benefits:

♦14,000 Volts – provides stronger / hotter spark.

♦Energy Efficient – uses only 40 VA versus approximately 240 VA standard.

♦Constant Secondary Voltage – does not fluctuate with changes in primary voltage supply.

♦Does Not Weaken Over Time – either works or it doesn’t.

♦Lighter – weighs several pounds less than a standard transformer.

♦Standard Off the shelf Part – no more special OEM transformer specifications. It is

backward compatible.

♦Warranty – 3 years.

For additional information on the operation of the controls including possible causes of lock-out

and latch-up, refer to the instruction manual supplied with each burner.

Attachments: WGO, WTGO, SGO & SGO-W Wiring Addendum #550-141-851/0599

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Weil-McLain Chaudière

Weil-McLain

Weil-McLain WGO Manuel utilisateur

Weil-McLain

Weil-McLain GOLD CGt SERIES Manuel utilisateur

Weil-McLain

Weil-McLain CGA 2 Series Manuel du produit

Weil-McLain

Weil-McLain RS Manuel utilisateur

Weil-McLain

Weil-McLain AHE Series Manuel utilisateur

Weil-McLain

Weil-McLain GOLD CGa-25 Manuel utilisateur

Weil-McLain

Weil-McLain Gold CGs-4E Manuel utilisateur

Weil-McLain

Weil-McLain Series 4 Manuel utilisateur

Weil-McLain

Weil-McLain ULTRA Oil 3 Series Manuel utilisateur

Weil-McLain

Weil-McLain Gold GV Series 4 Mode d’emploi

Weil-McLain

Weil-McLain Eco Tec 2 Series Manuel utilisateur

Weil-McLain

Weil-McLain HE (Series 2) Mode d’emploi

Weil-McLain

Weil-McLain Gold GV 1 series Mode d’emploi

Weil-McLain

Weil-McLain PFG 7 Series Mode d’emploi

Weil-McLain

Weil-McLain HE (Series 2) Manuel utilisateur

Weil-McLain

Weil-McLain Aqua Balance WMB-155 Manuel utilisateur

Weil-McLain

Weil-McLain CGM (Series 9) Manuel utilisateur

Weil-McLain

Weil-McLain GV90+ Mode d’emploi

Weil-McLain

Weil-McLain SlimFit 3 Series Guide de configuration

Weil-McLain

Weil-McLain FLAME GUARDIAN WMBC-1A Manuel d'utilisation et d'entretien

Weil-McLain

Weil-McLain CG Series 11 Manuel utilisateur

Weil-McLain

Weil-McLain 94 Series Manuel utilisateur

Weil-McLain

Weil-McLain SVF 1500 Manuel utilisateur

Weil-McLain

Weil-McLain Ultra Oil Mode d’emploi

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur