Weil-McLain 88 Manuel utilisateur

C-809(0308) 1

I. General Requirements

A. Furnish and install ( ) low pressure, wet base, cast iron sectional boiler(s) with power

burner(s) that pressurize the firebox and operate under forced and balanced draft at a

minimum of 85.6% Oil Thermal efficiency and 83.1% Gas Thermal efficiency.

B. Assemble and install boiler-burner unit(s) in compliance with manufacturers installation

instructions. All work must be done in a neat and workman like manner.

C. Weil-McLain (P)(A)(B) L, (P)(A)(B) G, (P)(A)(B) GL- ( )88-(W) (S)F boiler(s) with burner(s)

capable of burning natural gas at ( )” W.C. inlet pressure and/or No. 2 fuel oil.

1. (B) Boiler-burner unit Field assembled (standard).

2. (A) Boiler-burner unit with factory assembled sections.

3. (P) Boiler-burner unit completely packaged and fire tested

4. Natural or LP gas fired and/or No. 2 fuel oil.

5. Water or steam.

6. Forced or balanced draft.

D. Boiler(s) shall have I=B=R Hydronics Institute gross output(s) at 100% firing rate –

( ) MBH per boiler.

E. Boiler(s) shall be manufactured by ISO 9001 registered company to conform to Section IV of

the ASME Boiler and Pressure Vessel Code.

1. Individual sections (and section assembly) to be hydrostatically pressure tested at

factory in accordance with ASME requirements.

2. Maximum allowable working pressure 80 PSIG water and 15 PSIG steam cast as part

of section with ASME symbol.

F. Regulatory Requirements

1. Boiler(s) and controls to comply with applicable regulations.

2. Provide U.L. labeled burner(s).

3. Provide add option for local code(s) ie: MASS Code, BAR

G. Submittals

1. Submit shop drawings and product data.

2. Submittal packet to include boiler (and burner) manufacturer descriptive literature,

installation instructions, operating instructions, and maintenance instructions.

88 SERIES 2 BOILER

SUGGESTED SPECIFICATIONS

C-809(0308)

II. Product

A. Acceptable boiler/burner manufacturer(s) include(s):

1. Weil-McLain only, as specified in Part 1, Paragraph C.

2. Other manufacturer(s) or other Weil-McLain boiler(s) must comply with specifying

engineer’s requirements, including:

a) Full intent of these specifications, and provide complete submittal including

literature, wiring diagrams, fuel piping diagrams, and a list of similar installations.

b) Submittal to be presented to specifying engineer at least seven working days for

approval before bid opening. Substitutions are not permitted after contract is

awarded.

c) Burner(s) and Energy Management Control System(s) must be tested and

approved for installation with specified boiler-by-boiler manufacturer.

B. Boiler construction

•Boiler sections

•Assembled with short, individual draw rods.

•Cast with sealing grooves for high temperature sealing rope to assure permanent gas-

tight seal.

•Sealed watertight by elastomer sealing rings, not cast iron nipples. Each port opening

is machined to completely capture sealing ring between sections.

•Must be hydro-wall design to provide completely water-cooled combustion chamber.

•Provided with sufficient tappings to install required controls.

•Limited 10-year warranty against workmanship and defects to be in writing by

manufacturer.

C. Boiler(s)

•Provided with HXT bars to maximize heat transfer

•Provided with cast-in air elimination to separate air from circulating water.

•Provided with expansion tank tapping to divert separated air to expansion tank.

•Constructed to provide balanced water flow through entire section assembly using

single supply and return connections for water. No external headers are necessary for

water. Steam requires two or more supplies to anexternal header 24” minimum from

the waterline to the bottom of the header.

•Designed with a low silhouette to provide maximum headroom.

•Furnished with insulated burner mounting plate having necessary holes and tappings

to mount burner. High temperature sealing rope is used to provide permanent gas-

tight seal between front section and plate.

•Furnished with two observation ports (one in front and one in back) to allow visual

inspection of the flame.

•Provided with cast iron flue collar with a built-in adjustable damper capable of being

locked into place after adjustment.

•High temperature sealing rope used to provide permanent gas-tight seal between

hood and section assembly.

•Furnished with heavy gauge steel cleanout plates to cover cleanout openings on the

side of the boiler(s).

C-809(0308) 3

•Port openings must be of captured seal design – a machined groove assures uniform

compression of the sealing ring and protects the seal from contaminants. Elastomer

sealing rings are to be used to provide permanent watertight seal between sections.

Unlike cast iron or steel push nipples, the elasticity of the seals fills any gaps caused

by misalignment or expansion or contraction.

•Shipped with insulated heavy gauge steel jacket(s) with durable powdered paint

enamel finish. Jacket designed to be installed after connecting supply and return

piping. Side panels can be removed without tools for easy servicing.

D. Tankless heaters or indirect water heaters

•Provide ( ) internal tankless water heater(s) inserted into the left hand side of the

tankless intermediate (TI) section in the opening provided. Allow 34” minimum

clearance on left side of boiler for cleaning and servicing. Tankless openings must be

on same side as the flue passage cleanout plates to minimize space requirements.

E. Boiler foundation(s):

•Installer to construct needed support and level concrete foundation(s) where boiler

room floor is uneven or will not support the weight of the boiler(s).

F. Boiler trim:

1. All electrical components to be of high quality and bear the U.L. label.

a) Water boiler(s) controls furnished:

1) Combination low temperature limit (operating) and manual reset high

temperature limit control.

2) Low temperature limit set according to system design. High temperature limit set

at least 20°F higher than the low limit (240°F is the maximum allowable water

temperature).

3) Combination pressure-temperature gauge with dial clearly marked and easy to

read.

4) ASME certified pressure relief valve, set to relieve at 30 PSIG. Optional relief

valves available up to and including maximum allowable pressure. Side outlet

discharge type; contractor to pipe outlet to floor drain or near floor, avoiding any

area where freezing could occur.

b) Steam boiler(s) standard controls furnished:

1) Low pressuretrol (operating) and high pressuretrol set at maximum pressure as

a safety control.

2) Steam pressure gauge with dial clearly marked and easy to read.

3) Gauge cock water set with gauge glass, guards and aluminum water level plate.

4) ASME certified pressure relief valve, set to relieve at 15 PSIG. Side outlet

discharge type; contractor to pipe outlet to floor drain or near floor, avoiding any

area where freezing could occur.

c) Low water cut-off for water or steam boiler(s):

1) Boiler(s) to be furnished with U.L. labeled low water cut-off with ASME working

pressure rating equal to the ASME rating of the relief valve.

2) Do not use quick-connect fittings on boiler(s).

3) Install cut-off according to manufacturer’s instructions.

C-809(0308)

4) Locate so burner shuts down if boiler water level falls below allowable safe

waterline (steam boilers, ¼” above bottom of gauge glass).

5) Steam boiler primary low water cut-off shall be a float type – auto reset.

6) Steam boiler secondary low water cut-off shall be float or probe – manual reset.

III. Burner(s) construction, features and requirements:

1. Burner fuel supply system and burner installation to conform to burner manufacturer’s

installation instructions and applicable codes.

2. Burner motor characteristics: 120/60/1, 240/60/1, 208/60/3, 240/60/3,

480/60/3.

3. Control characteristics 120/60/1.

4. Burner fuel – natural gas/LP 4.0” W.C. minimum, No. 2 fuel oil.

5. Code(s) - standard boiler, CSD-1, FM, IRI

6. Burner(s) to have U.L. label(s) supplied by the burner manufacturer.

7. Burner(s) designed to ensure high efficiency and good performance under forced draft

conditions with 0.1” W.C. positive pressure at the flue collar.

8. Burner to be adjusted to provide 9.5 to 10.0% CO2for gas and/or 11.5 to 12% CO2

with zero smoke for oil firing.

9. Burner(s) manufactured by:

Power-Flame, Riello, Webster, Carlin, Beckett

10. Burner operating mode: on-off, low-high-off, low-high-low, modulating

A. Panel options – power on/fuel on light is standard on all burner(s) with panels.

1) Call For Heat

2) Ignition On

3) Pilot Failure

4) Low Water

5) Flame Failure

6) Silencing Switch

7) Control Fuse and Holder

8) Post Purge Timer

9) Alarm Bell

B. Start-up and Service

•The contractor shall obtain the services of a factory-authorized agent to provide

burner light off and adjustment. The start-up agent shall provide a burner light-off

report as written proof that the burner was adjusted to optimum performance.

•The authorized agent shall provide a one-year service warranty after start-up.

Autres manuels pour 88

Table des matières

Autres manuels Weil-McLain Chaudière

Weil-McLain

Weil-McLain EVERGREEN PRO 1 EVG-110 Mode d’emploi

Weil-McLain

Weil-McLain CGi Series 2 Manuel utilisateur

Weil-McLain

Weil-McLain EGH-85 Series Manuel utilisateur

Weil-McLain

Weil-McLain Gold GV Series 4 Manuel utilisateur

Weil-McLain

Weil-McLain GV90+ Instructions d'installation et d'utilisation

Weil-McLain

Weil-McLain GOLD CGt SERIES Manuel utilisateur

Weil-McLain

Weil-McLain VHE Series 3 Manuel d'utilisation et d'entretien

Weil-McLain

Weil-McLain Gold GV Series 4 Mode d’emploi

Weil-McLain

Weil-McLain SlimFit Manuel utilisateur

Weil-McLain

Weil-McLain GV90+3 Manuel utilisateur

Weil-McLain

Weil-McLain GOLD CGi-4E Manuel utilisateur

Weil-McLain

Weil-McLain CGi Series 3 Manuel du produit

Weil-McLain

Weil-McLain 78 Manuel utilisateur

Weil-McLain

Weil-McLain CGi Series 2 Manuel utilisateur

Weil-McLain

Weil-McLain CG Series 10 Manuel utilisateur

Weil-McLain

Weil-McLain LGB-5 Manuel utilisateur

Weil-McLain

Weil-McLain Boiler Manuel utilisateur

Weil-McLain

Weil-McLain GOLD CGt SERIES Mode d’emploi

Weil-McLain

Weil-McLain Gold GV 3 Series Mode d’emploi

Weil-McLain

Weil-McLain PD Gas Series 3 Manuel utilisateur

Weil-McLain

Weil-McLain CGA 2 Series Manuel du produit

Weil-McLain

Weil-McLain Gold Series 2 Manuel utilisateur

Weil-McLain

Weil-McLain Oil Boiler Manuel utilisateur

Weil-McLain

Weil-McLain WGO 4 Series Manuel utilisateur

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur